Time jitter analysis of 1-bit sigma-delta synthesizer

This letter presents a general analysis of time jitter in sigma-delta synthesizer. One of the practical applications of 1-bit sigma-delta systems is a generation of high-resolution local oscillator (LO) signals. In order to generate LO signals, one may use a single-bit sigma-delta technique to encode sine waves. Today, direct generation of high-frequency sine wave using a clock with higher frequency, is possible. In this letter, we will analyze different LO signal generators and develop a practical way of computation to decide how to choose the best configuration under minimum degradation of signal-to-noise ratio (SNR) at the output.     

A basic program for calculating subsurface water temperatures using chemical geothermometers-implication to geothermal reservoir estimation

GEOTHERM is a computer program written in BASIC language to estimate geothermal reservoir temperature using the well-known chemical gèothermometers. The empirical equations used in the program were obtained from the literature. Three different chemical geothermometers are included in the program: Na-K, Na-K-Ca, and silica geothermometers; this gives the user the opportunity not only to select the most reliable geothermometer in estimating subsurface temperature, but also to select the type of geothermometer according to available data. A sample input file of geothermal waters obtained from Iceland has been tested, so as to show the applicability and usefulness of the program.     

Improving security of the Internet of Things via RF fingerprinting based device identification system

Neural Computing and Applications - Security is one of the primary concerns when designing wireless networks. Along detecting user identity, it is also important to detect the devices at the...     

Stress-Induced Lattice Imperfections: the Principal Motive in Enhancing some Physico-Chemical and Electrical Properties of some Quartz Varieties

Silicon - Chemical reactivity, grindability and zeta potential have been measured and correlated for three variably deformed quartz varieties from three different areas. Results show that there is...     

Temperature-dependent diffusion coefficient of soluble substances during ethanol extraction of clove

The temperature dependence of the diffusion coefficient of ethanol-soluble substances from ground cloves (particle size 250 μm) during extraction was estimated by fitting batch extraction data at several temperatures (27.8, 40, 50, and 60°C) to a previously developed mass transfer model. The model was based on spherical geometry of particles. Nonlinear regression analysis was used to develop an equation that describes the diffusivity as a function of temperature. The temperature dependence ofD _A was of the Arrhenius type.     

Mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

Polypropylene (PP) hybrid composites have been produced by compounding two types of mineral fillers, viz., talc and kaolin with PP copolymer using a twin screw extruder. The PP hybrid composite was injection‐molded into dumbbell specimen for tensile, flexural, and impact properties characterizations. MFI and SEM studies were used to characterize the flow and morphological properties of the PP hybrid composites. The result shows that most of the hybrid composites showed a significant decrease in flow, tensile, flexural, and impact properties compared with the single filler‐filled PP composites. However, a hybridization effect was seen for the PPT20K10 hybrid composites, through the synergistic coalescence of positive characteristics from 20 wt % of talc and 10 wt % of kaolin. This hybrid formulation have given an economically advantageous material with the mechanical properties (tensile, flexural, and impact) comparable to those of the talc‐filled PP composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 434–441, 2007     

Dielectric properties of SBR vulcanizates loaded with HAF carbon black and BaTiO3 ceramics

The influence of HAF carbon black and BaTiO₃ ceramic powder contents in SBR vulcanizates on the dielectric constant (ε′) at different frequencies and at fixed temperature of 303 K is studied well in this article. The temperature dependence of the ac conductivity (σ_ac) was also studied. ε′ appreciably decreases as frequency increased for both filled and unfilled SBR vulcanizates. At each frequency, ε′ gradually decreased with BaTiO₃ loading, but its change at any fixed frequency with BaTiO₃ filler loading is not uniform. For HAF group ε′ (at loading ≥ 40 phr), drops rapidly with frequency. Meanwhile, it increased appreciably beyond a certain HAF filler loading (≈ 20 phr). Experimental values of the dielectric constant of both BaTiO₃ and HAF contents were compared with those calculated by using Tsangaris, Clausius and Bruggman models. Tsangaris model with simple modifications was applied and a fairly good agreement was obtained. The HAF particles or aggregates was found to take the shape of oblate ellipsoids with the minor axes parallel to the applied frequency as detected from the decreasing behavior of the depolarizing factor (Y) with HAF contents. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2227–2234, 2007     

Effect of competitive interference on the biosorption of lead(II) by Chlorella vulgaris

Batch experiments were carried out to asses the effect of Cu(II) and Zn(II) on the biosorption of lead(II) ions by non-living Chlorella vulgaris. The uptake of Pb(II) was examined for single, binary and ternary solutions at different initial concentrations and different pH values. The experimental results showed that the uptake increased with increasing pH from 3.0 to an optimum value of 5.0. The biosorption of Pb(II) was found to be adversely affected by the presence of Cu(II) ions, while Zn(II) ions seemed to have negligible effect on the process. The equilibrium data were fitted to four isotherm models: Langmuir, Freundlich, Sips and Dubinin–Radushkevich; the Sips isotherm gave the best fit for the data. Modeling of the controlling mechanisms indicated that both intrinsic kinetics and mass transfer played major roles in controlling the process. A new dimensionless parameter, Ψ, was defined to asses the relative contributions of the two mechanisms to the biosorption of lead(II). Mass transfer seemed to be the dominant mechanism at low initial lead(II) concentrations, while intrinsic kinetics dominates at high concentrations.     

UV-shielding by a polyurethane/f-Oil fly ash-CeO2 protective coating

A waste material called oil fly ash (OFA) was acid-functionalized, yielding f-OFA-COOH, which was then reacted with cerium oxide (CeO₂) to make CeO₂-functionalized OFA, or f-OFA-CeO₂. Pristine OFA and f-OFA-CeO₂ were used to make waterborne polyurethane (WBPU) dispersions, referred to as WBPU/OFA and WBPU/f-OFA-CeO₂, respectively, with defined OFA and f-OFA-CeO₂ content. All the dispersions were applied to mild steel as organic coatings to evaluate their protective properties, such as their hydrophobicity, adhesive strength and UV-shielding resistance. These protective properties varied based on the OFA and f-OFA-CeO₂ content. The highest water contact angle, minimum water swelling and maximum adhesive strength were found using WBPU/f-OFA-CeO₂-20 coating (using 2.00 wt% f-OFA-CeO₂), which also showed the maximum ultraviolet (UV) absorption via UV–vis spectroscopy analysis. This UV shielding result also matched field test results, as that coating was found to exhibit the lowest UV degradation near a marine atmosphere, as shown by X-ray photoelectron spectroscopy (XPS) analysis. The least affected hydrophobicity was also recorded for the sample with the WBPU/f-OFA-CeO₂-20 coating.     

Position‐Based Skinning for Soft Articulated Characters

In this paper, we introduce a two‐layered approach addressing the problem of creating believable mesh‐based skin deformation. For each frame, the skin is first deformed with a classic linear blend skinning approach, which usually leads to unsightly artefacts such as the well‐known candy‐wrapper effect and volume loss. Then we enforce some geometric constraints which displace the positions of the vertices to mimic the behaviour of the skin and achieve effects like volume preservation and jiggling. We allow the artist to control the amount of jiggling and the area of the skin affected by it. The geometric constraints are solved using a position‐based dynamics (PBDs) schema. We employ a graph colouring algorithm for parallelizing the computation of the constraints. Being based on PBDs guarantees efficiency and real‐time performances while enduring robustness and unconditional stability. We demonstrate the visual quality and the performance of our approach with a variety of skeleton‐driven soft body characters.