Self-oscillating dimmable electronic ballast

This paper presents a simple alternative for an electronic ballast operating in self-sustained oscillating mode with dimming capability for fluorescent lamps. A simple modification in one of the gate drivers side circuit allows the lamp to dim without compromising the simplicity, reliability, and low cost which characterize the self-oscillating electronic ballast (SOEB). A qualitative analysis is presented to explain the behavior of the proposed self-oscillating electronic ballast with dimming feature. In addition, the stability and the key equations for the design are derived using the extended Nyquist criterion and describing function method. Experimental results from two 40-W electronic ballasts are presented to demonstrate the performance and to validate the analysis carried out.     

Microchemical Engineering: Components,Plant Concepts User Acceptance – Part I

Over the last five years, many activities have focused on the unexploited field of carrying out reactions on small scales. Due to the rapid development of new components, this paper deals with recent developments only in a compressed form. An important point is the analysis of possible plant concepts for microreactors and whether these are a sensible option. Due to the enormous difference in size between the microchannels and the fluid periphera of possible components this is not just a technical question. It touches on the microtechnology concept as a whole. The direction in which the field should be developed and which measures can be taken to influence its development are questions that are addressed here with respect to the big industrial interest in microreactors.     

Scale Up from Small Oven-Drying Tests of Mineral Concentrate to Pilot-Scale Drying with a Heated Pad

While Fickian diffusion models are commonly used in other applications, there are few reports of them being applied to the batch drying of a mineral concentrate. Diffusion coefficients estimated from small-scale oven-drying tests were used to predict the drying behavior of a concentrate sample 1 m × 1 m in area and 50 cm deep, with a heated bottom pad. These pilot-scale tests included both daily turning of the sample and turning every three days. The excellent quantitative agreement between the predicted and observed pilot-scale behavior gives a high level of confidence in the model predictions and suggests that a Fickian diffusion model is adequate to predict the behavior of mineral concentrates at the low moisture contents used here.     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

Impact of crosstalk in an arrayed-waveguide multiplexer onN×N optical interconnection

The impact of crosstalk in an arrayed-waveguide N×N wavelength multiplexer is investigated precisely in relation to its application to wavelength-routing N×N all optical networks. In such systems multiple crosstalk light which has the same wavelength as the signal results in signal-crosstalk beat noise. We confirm that the noise is Gaussian and obtain the relation between crosstalk and power penalty. It is shown that the crosstalk must be less than -38 dB for a 16×16 system to keep the power penalty below 1 dB at a bit error rate of 10^-9     

Aperture sampling requirements in planar near-field and patterncalculations

The paper covers a simple idea. If we sample an aperture, we can obtain valid patterns over a limited angular region about the normal to the aperture. The same expression can be used with near-field measurements. I reduced the expression to a nomograph. A nomograph allows one to rapidly test various choices. In the second half of the paper, I answer questions caused by the February column which discussed polarization (Milligan, IEEE Antennas. Propag. Mag., vol.38, no.1, p.56-8, 1996)     

Interaction of triton X-100 on silica: A relationship between surface characteristics and adsorption isotherms

Adsorption of Triton X-100 on various silica substrates has been investigated. A number of solids, including a natural quartz, this quartz washed with HCl acid and subsequently heated at 1273 K; two aerosils and one Kieselgel silicas were studied. These solids exhibit surface areas in the range of 5 to 430 m² g^?1. All the Triton adsorption isotherms display an S-shape at the adsorption temperatures studied (298 and 308 K). It has been found that the pretreatments of natural quartz (by water washing, impurities removed by acid and/or high temperature calcination) affect considerably the amounts of TX-100 adsorbed. Measurements of surface composition have been made by X-ray photoelectron spectroscopy (XPS) with particular emphasis on the presence of impurities and on the number of OH groups at the surface of the samples. The nature of the surface hydroxyl has also been studied by infrared spectroscopy. Furthermore, the specific number of hydroxyl groups on the surface of the silica samples has been determined by thermogravimetric analysis. Finally an attempt to correlate solid surface characteristics with adsorption isotherms has been developed.     

Experimental estimate of self-irradiation of building bricks due to incorporated radionuclides

A method is described for experimentally determining the dose rate created in building bricks by incorporated natural radionuclides. It was established using the thermoluminescence dosimetry method that the measured dose rate depends on the detector thickness, the mass of the ceramic product investigated, and the irradiation geometry. The contributions to the measured dose of weakly penetrating α and β radiation and hard ψ radiation are separated, the ratio between them depending on the experimental conditions. Translated from Izmeritel'naya Tekhnika, No. 7, pp. 62–66, July, 1996.