Using ion implantation to adjust the transition temperature of superconducting films

We summarize a continuing investigation into using ion implantation to alter the transition temperature of superconducting thin films. The primary motivation for the work presented here was to study the feasibility of using magnetic ion doping to replace the bi-layer T_c control process currently used for certain cryogenic detector applications at National Institute for Standards and Technology. The results from work with various ion species implanted into aluminum, molybdenum, titanium and tungsten host films are presented.     

Synthesis and Properties of NdMCr2O5 (M = Na, K, Cs) and NdMgCr2O5.5 Chromites

NdMCr₂O₅ (M = Na, K, Cs) and NdMgCr₂O_5.5 are prepared by solid-state reactions between appropriate oxides and carbonates and are shown to have a tetragonal structure. The heat capacity of these chromites, measured from 298.15 to 673 K, exhibits sharp changes attributable to second-order phase transitions. The C _p ⁰(T) data are represented by quadratic best fit equations. The electrical resistivity of the chromites is measured between 303 and 493 K. The results attest to semiconducting behavior of the materials in certain temperature ranges.     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

Design and fabrication of RESURF MOSFETs on 4H-SiC(0001), (112~0), and 6H-SiC(0001)

Design and fabrication of lateral SiC reduced surface field (RESURF) MOSFETs have been investigated. The doping concentration (dose) of the RESURF and lightly doped drain regions has been optimized to reduce the electric field crowding at the drain edge or in the gate oxide by using device simulation. The optimum oxidation condition depends on the polytype: N/sub 2/O oxidation at 1300/spl deg/C seems to be suitable for 4H-SiC, and dry O/sub 2/ oxidation at 1250/spl deg/C for 6H-SiC. The average inversion-channel mobility is 22, 78, and 68 cm/sup 2//Vs for 4H-SiC(0001), (112~0), and 6H-SiC(0001) MOSFETs, respectively. RESURF MOSFETs have been fabricated on 10-/spl mu/m-thick p-type 4H-SiC(0001), (112~0), and 6H-SiC(0001) epilayers with an acceptor concentration of 1/spl times/10/sup 16/ cm/sup -3/. A 6H-SiC(0001) RESURF MOSFET with a 3-/spl mu/m channel length exhibits a high breakdown voltage of 1620 V and an on-resistance of 234 m/spl Omega//spl middot/cm/sup 2/. A 4H-SiC(112~0) RESURF MOSFET shows the characteristics of 1230 V-138 m/spl Omega//spl middot/cm/sup 2/.     

Auditory motivated level-crossing approach to instantaneous frequency estimation

We address the problem of estimating the instantaneous frequency (IF) of a phase signal using its level-crossing (LC) information based on front-end auditory processing motivation. We show that the problem of IF estimation using LC information can be cast in the framework of estimation from irregularly sampled data. The formulation has the generality of estimating different types of IF without the need for a quasistationary assumption. We consider two types of IF-polynomial and bandlimited; we use polynomial interpolating functions for the former, and for the latter, we propose a novel "line plus sum of sines" model. The model parameters are estimated by linear regression. Considering the noisy case, LC data for different levels is analyzed, and methods for combining different estimators from LCs are discussed. Theoretical and extensive simulation results show that the performance of the zero-crossing (ZC) based IF estimator and the level-crossing based IF estimator with smaller level values is better than those obtained with higher level values or their combinations. The new technique reaches the Crame/spl acute/r-Rao bound (CRB) roughly above 4 dB signal-to-noise ratio (SNR), and its performance does not deteriorate rapidly with mismatch in the IF order compared with the other techniques in the literature.     

Entities,identities, identifiers and credentials — what does it all mean?

This paper looks at the concepts of entities, identities, identifiers and credentials, their definitions, and how they combine to authenticate an identity to an account, or function, within a service. Credentials can be divided into several different types on the basis of their use, origin and characteristics. In particular, types such as composite, dynamic and derived credentials will be considered, and their applicability within an identity management system. Each credential must be managed through its entire life cycle from initial registration, general use and suspension, to deletion. The notion of public (i.e. freely distributable) and private (i.e. known only to you) aspects of a credential is explored. The bindings, by trusted third parties, of identifiers and public credentials into permits and instruments of proof is explained along with the convenience, but greater exposure, of local information. Several scenarios are analysed in terms of how different types of credentials are employed during the authentication process.     

iShopFloor: an Internet-enabled agent-based intelligent shop floor

Global competition is driving manufacturing companies to change the way they do business. New kinds of shop floor control systems need to be implemented for these companies to respond quickly to changing shop floor environments and customer demands. This paper presents a new concept called iShopFloor-an intelligent shop floor based on the Internet, web, and agent technologies. It focuses on the implementation of distributed intelligence in the manufacturing shop floor. The proposed approach provides the framework for components of a complex control system to work together as a whole rather than as a disjoint set. It encompasses both information architecture and integration methodologies. The paper introduces the basic concept of iShopFloor, a generic system architecture, and system components. It also describes the implementation of eXtensible Markup Language message services in iShopFloor and the application of intelligent agents to distributed manufacturing scheduling. A prototype environment is presented, and some implementation issues are discussed.     

Peak-to-average power reduction in space division multiplexing based OFDM systems through spatial shifting

A new method to reduce the peak-to-average power ratio (PAPR) in space division multiplexing systems applying orthogonal frequency division multiplexing is proposed. The method applies spatial shifting to partial transmit sequences to achieve a decreased PAPR on all transmit branches.     

Video Compression - From Concepts to the H.264/AVC Standard

Over the last one and a half decades, digital video compression technologies have become an integral part of the way we create, communicate, and consume visual information. In this paper, techniques for video compression are reviewed, starting from basic concepts. The rate-distortion performance of modern video compression schemes is the result of an interaction between motion representation techniques, intra-picture prediction techniques, waveform coding of differences, and waveform coding of various refreshed regions. The paper starts with an explanation of the basic concepts of video codec design and then explains how these various features have been integrated into international standards, up to and including the most recent such standard, known as H.264/AVC.