Corrosion characteristics of aluminium alloy graphite particulate composite in various environments

The present study was aimed at understanding the response of 2014 Al alloy dispersed with graphite particles in various corrosive environments. Marine (sodium chloride) as well as acidic media were selected for the purpose with a view to widen the range of utility of the composite for applications where such environments may be encountered. Studies were also extended to characterize the corrosion resistance of the composite in fresh as well as used lubricating oils to explore the possibilities of using it in bearing, bushing and such other applications. The corrosion behaviour of the base alloy processed under identical conditions was also examined in the above media to see the influence of graphite addition in the alloy. In order to assess the role of the matrix microstructure, the composite as well as the base alloy was subjected to corrosion in heat-treated as well as-cast conditions. It was observed that the specimens suffered from the maximum rate of corrosion in acid, while sodium chloride produced the minimum corrosion rate. Oil in both used and fresh conditions revealed a negligibly small extent of corrosion. The composite was found to show a higher rate of corrosion than the base alloy under identical test conditions. This was attributed to the dispersoid/matrix interfacial corrosion in the case of the graphitic aluminium alloy. Heat treatment of the composite and the base alloy was found to lower the rate of corrosion in the environments tested. Microstructural modifications of the matrix and possible relief of residual stresses were thought to be responsible for the lower rate of corrosion in the heat-treated condition.     

Significance of DNA ploidy in the treatment of T1 glottic carcinoma

OBJECTIVE: To assess the role of DNA ploidy as a predictor of radioresistance in T1 glottic carcinoma. DESIGN: Case-control study. Flow cytometric DNA ploidy measurements were performed on formalin-fixed paraffin-embedded tumor specimens from 15 patients with T1 glottic laryngeal carcinomas in whom radiotherapy had failed and from a matched group of 15 patients in whom an identical radiotherapy regimen was curative. Analysis of DNA content was performed blind to outcome of treatment. SETTING: Academic tertiary referral medical center. PARTICIPANTS: Thirty patients with clinically staged T1, N0, M0 glottic carcinoma. INTERVENTION: All patients received radiation to the larynx through opposed lateral ports at a total dose of 64 to 70 Gy. RESULTS: Ten diploid and five aneuploid histograms were found in the resistant group, and six diploid and nine aneuploid histograms were found in the radiosensitive group. This difference was not statistically significant. A trend toward a higher relapse rate after radiotherapy (62.5%) among patients with diploid tumor compared with those with aneuploid tumor (35.7%) was noted. CONCLUSIONS: DNA ploidy did not predict response to radiotherapy in patients with T1 glottic cancer, probably because of the small number of patients. A trend toward lower risk of local recurrence after radiotherapy in aneuploid tumors was noted. A larger prospective study is needed to assess the value of DNA ploidy in the treatment of early laryngeal cancer.     

Effect of precyclic loading on stress-corrosion-cracking initiation in an X-65 pipeline steel exposed to near-neutral pH soil environment

A study was carried out to understand the effect of precyclic loading on stress-corrosion-crack initiation in an X-65 pipeline steel exposed to a near-neutral-pH soil environment. The test specimens were precyclically loaded before corrosion exposure to represent a service history of up to about 20 years, depending on the severity of pressure fluctuation. Microcracks had initiated on the polished surface of the X-65 pipeline steel after long-time exposure at open-circuit potential (OCP) in a near-neutral-pH synthetic soil solution. These microcracks were mostly initiated from pits at metallurgical discontinuities such as grain boundaries, pearlitic colonies, and banded phases in the steel. Strong preferential dissolution was observed along planes of the banded structures in the steel. The selective corrosion attack at these metallurgical discontinuities is attributed to the galvanic nature of those areas to their neighbors. Cyclic loading prior to corrosion exposure had significant effects on microcrack initiation and propagation during subsequent corrosion exposure. Cyclic loading prior to corrosion exposure either reduced or increased the probability of crack initiation and the rate of crack propagation, depending upon the magnitude of the stress cycles. The largest reduction was seen at a peak cyclic stress of about 0.8 of the yield strength. This cyclic-loading-dependent cracking behavior might be related to the alteration of the substructures and the residual stress in the steel as a result of precyclic loading.     

Unsaturated diffusivity functions for concrete derived from NMR images

Deterioration of concrete or reinforcing steel through excessive contaminant concentration is often the result of repeated wetting and drying cycles. At each cycle, the absorption of water carries new contaminants into the unsaturated concrete. Nuclear Magnetic Resonance (NMR) is used with large concrete samples to observe the shape of the wetting profile during a simple one-dimensional wetting process. The absorption of water by dry concrete is modelled by a nonlinear diffusion equation with the unsaturated hydraulic diffusivity being a strongly nonlinear function of the moisture content. Exponential and power functions are used for the hydraulic diffusivity and corresponding solutions of the diffusion equation adequately predict the shape of the experimental wetting profile. The shape parameters, describing the wetting profile, vary little between different blends and are relatively insensitive to subsequent re-wetting experiments allowing universal parameters to be suggested for these concretes.

---

Résumé La détérioration du béton ou du béton armé à travers la concentration excessive de contaminant est souvent le résultat de cycles humides et secs répétés. A chaque cycle, l'absorption de l'eau amène de nouveaux contaminants à l'intérieur du béton non saturé en eau. Pour observer le profil du processus d'humidification, on peut utiliser la Résonance Magnétique Nucléaire (RMN) sur de grands échantillons de béton dans le cadre d'une simple étude unidimensionnelle de ce profil. Il est démontré que l'absorption d'eau par du béton sec peut être précisément modélisée par une équation de diffusion non linéaire où la diffusivité hydraulique non saturée est fonction hautement non linéaire de l'humidité du contenant. Des fonctions exponentielles et puissances peuvent définir la diffusivité hydraulique. Les solutions résultant de l'équation modélisant cette diffusion permettent de prédire avec précision la forme du profil de l'humidification expérimentale. Les paramètres de forme qui décrivent le profil de l'humidification varient peu entre les différents mélanges de béton et sont relativement insensibles à des expériences de réhumidification ultérieures. Cela permet de suggérer que ces bétons suivent des paramètres d'humidification universels.

     

Traveling-wave amplifiers with prescribed frequency response

Microwave transistor amplifier combinations that have controlled frequency response over a specified bandwidth were designed. Theoretical analysis of such an amplifier with an arbitrary number of sections is presented. The response of the amplifier is controlled by tapering the frequency selectivity or Q of each section of the amplifier. To verify the theory, a three-section amplifier with maximally flat time delay response was designed, constructed, and evaluated. Existing traveling-wave amplifiers were modeled as lossy transmission lines. Although the amplifiers were relatively broadband, a prescribed frequency response was not achieved, and each transistor did not receive an equal portion of the signal power. Resistive elements were required for impedance matching at the input and output. The design seeks to improve on previous techniques by trading bandwidth for controlled gain. By making the transmission line that connects the amplifier sections nonuniform, the frequency response was controlled over the design bandwidth. The designs can easily be implemented using familiar components     

Grain size effects on the mechanical properties of some squeeze cast light alloys

Mechanical property-grain size relationships have been examined for squeeze cast Al-4.5% Cu alloy, for an aluminium alloy with a composition corresponding to wrought 7010, and for a magnesium alloy AZ91. The general trend of the results obtained showed that the tensile properties and the fatigue strength improved as grain size decreased and the reverse was found to be the case for the fatigue crack propagation resistance and fracture energy of these castings. However, the results also showed that no simple common relationship existed between grain size and the tensile properties of the different alloys. The results are discussed in respect of their microstructures.     

Chelated alkoxyalumoxanes and a silica-free binder based on them

Chelated alkoxyalumoxane oligomers have been synthesized through consecutive hydrolysis and alcoholysis of organoaluminum compounds stabilized by compounds capable of keto-enol tautomerism. The chelated alkoxyalumoxanes were used to prepare a silica-free binder for the fabrication of heat-resistant (up to 2050°C), chemically inert corundum ceramic composites. The likely structures of the synthesized preceramic alumoxane oligomers were inferred from physicochemical characterization results (¹H, ¹³C, and ²⁷Al NMR, IR spectroscopy, mass spectrometry, gel-permeation chromatography, thermal analysis, and elemental analysis).