OTDM transmitter using WDM-TDM conversion with an electroabsorptionwavelength converter

An all-optical multiplexing technique using wavelength division multiplexing (WDM)-time division multiplexing (TDM) conversion with an electroabsorption wavelength converter has been proposed and demonstrated. The effectiveness of this WDM-TDM conversion technique for various pulsewidth settings was experimentally investigated. The fluctuation of the signal performance, which was inevitably caused by the coherent crosstalk between adjacent pulses in the conventional optical time division multiplexing (OTDM) technique, were successfully suppressed, even in the case of wide pulse duration. High Q-factor performance has been maintained for a wide range of duty ration from 36% to 74%. By introducing this technique to the optical time division multiplexer, a highly stable and high-quality 40-Gb/s optical signal can be effectively produced without generating the short pulse or setting two tributaries at orthogonal polarization states, and without introducing high-speed electronics for signal multiplexing. The WDM-TDM conversion with an electroabsorption wavelength converter was extended to 60-Gb/s operation by using three 20-Gb/s tributaries. A clear eye opening was confirmed for a waveform after the WDM-TDM conversion of the 60-Gb/s signal     

The Solutions for Adjustment and Reconstruction of Water-Drive Surface Systems in the Old Areas of Daqing Oilfield

Introduction 　　Owing to long-time running, more facilities including stations, pipelines, vessels have become corrosive and aged ,some process has grown old, it has exert more burden for the maintenance and repair.Simultaneously, the fluid production rate, oil production rate and water injection rate has changed greatly so that the inflicts and problems from the established surface systems will become more obvious. Energy cost of production and running has increasing continuously. Capacity has been unbalance in systems and areas. 　　……     

International legislation on trace elements as contaminants in food: a review

Environmental contaminants such as trace elements may be present in all foods. Foods, raw materials and ingredients for food production are to an increasing extent traded across borders. Hence, there is a need for international legislation on trace elements as contaminants in food. In 1961, the FAO and WHO established the Codex Alimentarius to elaborate international food legislation. Contaminants in food are handled by the Codex Committee for Food Additives and Contaminants (CCFAC). The Codex Alimentarius system for developing legislation concerning trace elements as contaminants in food is based upon the Codex General Standard for Contaminants and Toxins in Food (GSCTF). By October 2001, the principles for setting maximum limits (MLs) for contaminants in food are agreed, and work is in progress on MLs for trace elements such as lead and cadmium in the various food categories. The status for the proposals is presented and discussed. The EU Regulation 466/2001 of 8 March 2001 sets MLs for lead and cadmium in various foods. This regulation will apply from 5 April 2002. The EU regulation is more detailed but similar to the Codex draft standards for lead and cadmium in food. In future, legislators and administrators in the Codex and EU and analytical chemists will discuss how to use more and better analytical data as risk-management tools to protect public health. Trace elements' speciation is an important aspect of this discussion.     

The effects of pressure on the isothermal fluid behavior of bituminous coals

An investigation into the effects of pressure (helium gas) on the isothermal fluid behavior includes: (1) the effect of pressure on the rate of melting and coking as evidenced by the rate constants k(melt) and k(coke); (2) the effect of pressure on the energies of activation of melting and coking; (3) the effects of pressure on the characteristic times; (4) the effects of pressure on the maximum isothermal fluidity. Results from the effects of pressure on k(melt) revealed that it was generally the high total sulfur, low nitrogen, low reactives/mineral matter ratio, medium rank coals which show the greatest increase in k(melt), whereas the highest rank coals show the least decrease in k(coke). The energies of activation of melting and coking were not significantly affected by pressure. The investigation also reveals increases or decreases in the respective times of softening, maximum fluidity, resolidification and total time of fluid behavior under isothermal pressurized conditions. There appears the possibility that these shifts may be rank dependent. Additionally, the lower rank coals show the largest relative increase in their fluidities when subjected to pressure. Empirical relationships were derived in order to quantitatively predict the maximum isothermal fluidity for most (fluid) coals at a given pressure.     

关于粒子加速器人身辐射安全联锁系统设计原则的建议

本文讨论了在粒子加速器上的联锁系统设计中应遵循的一些原则,其中建立隔离区、“失效导致安全(Fail-safe)”,使用“硬件”、“多重联锁”、设置急停开关等是最重要的。     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

Security issues for downloaded code in mobile phones

'Software defined radio' (SDR) is a technology that will appear in future generations of mobile phones, i.e. following the third-generation mobile phone technology that is currently being defined and developed. Early versions of 'pragmatic' SDR will allow the terminal to be reconfigured at any level of its protocol stack. Ultimately, the 'pure' SDR technology will allow a mobile phone or terminal to have its air interface software configured or reconfigured by other software (or software parameters) that have been downloaded to the terminal, e.g. over the air, or from a remote server via the Internet and one's personal computer (PC). A number of security issues arise with downloaded code that implements the air interface functions, and these may not be obvious simply from looking at the way PC software is updated on-line today. This paper starts with an outline of the code that allows a mobile phone to operate over a particular air interface. This sets the baseline for a discussion of the security issues surrounding the change of this code from one that is fixed and downloaded once only, to code that is reconfigurable during the life of a product.