Anaerobic biodecolorization of textile reactive anthraquinone and phthalocyanine dyebaths under hypersaline conditions.

The biological decolorization of two industrial, spent textile reactive dyebaths was investigated using a suspended-growth, halophilic mixed culture fed with glucose. Dyebath I contained mainly Reactive Blue 19 (RB19), an anthraquinone dye, whereas dyebath II contained mainly Reactive Blue 21 (RB21), a phthalocyanine dye. Batch assays under anaerobic conditions with the two neutralized dyebaths resulted in 87 and 37% extent of decolorization for dyebaths I and II, respectively. The rate of glucose utilization and the extent of acetate production were impacted in the presence of each dyebath as compared to the control culture. However, dyebath decolorization occurred despite moderate culture inhibition. Reuse of a biologically renovated RB19-containing dyebath in the dyeing process resulted in reproducible but not identical cotton fabric shades as compared to a standard dyeing (i.e., control) using fresh water. This difference is attributed to a variable degree of RB19 aggregation during the dyeing process and is not related to the efficiency of the biodecolorization process. Further improvement of the redyeing efficiency will lead to the development of an in-plant, closed-loop decolorization system resulting in significant water conservation and minimization of textile pollutants such as salt and dyes.     

Linearity stablized fiber-optic thermometer using pseudo-heterodyne phase detection

A temperature sensor using a fiber-optic Fabry-Perot interferometer is described. A pseudo-heterodyne detection scheme is adopted to read the light phase difference in the Fabry-Perot interference output. A higher harmonic components comparison method is used to stabilize the system and to increase detection linearity. This system realizes not only highly sensitive temperature sensing with good linearity and minimal adjusting error, but also application to the sensing of other physical quantities such as vibrations. Additionally, the signal-to-noise ratio and distortion of the detected signal are investigated as functions of fiber end reflectivity. These results will be useful in designing a high performance fiber-optic Fabry-Perot thermometer.     

Hot-carrier reliability of 20V MOS transistors in 0.13 μm CMOS technology

This paper presents results of reliability investigation of 20 V N-Drift MOS transistor in 0.13 μm CMOS technology. Due to high performances required for CMOS applications, adding high voltage devices becomes a big challenge to guarantee the reliability criteria. In this context, new reliability approaches are needed. Safe Operating Area are defined for switch, V_ds limited and V_gs limited applications in order to improve circuit designs. For V_ds limited applications, deep doping dose effects in drift area are investigated in correlation to lifetime evaluations based on device parameter shifts under hot carrier stressing. To further determine the amount and locations of hot carriers injections, accurate 2D technological and electrical simulations are performed and permit to select the best compromise between performance and reliability for N-Drift MOS transistor.     

On Routh-Pade model reduction of interval systems

This paper discusses another generalization of the direct Routh table truncation method for interval systems. It is shown that the existing generalization of the direct Routh table truncation fails to produce a stable system, in contradiction to the equivalent result for fixed-coefficients systems. The present method guarantees a stable reduced order model for interval systems as well.     

Numerical solution for shape optimization of an impactor penetrating into a semi-infinite target

The shape of the impactor with the maximum depth of penetration (DOP) for a given impact velocity is found using a numerical procedure for solving a corresponding non-classical variational problem. It is shown that the optimum shape in a general case is close to a blunt cone. The variation of the optimal shape of the impactor and the dependence of the DOP vs. the initial (impact) velocity and friction coefficient is studied. The analysis is performed also for optimal conical impactors.     

含V、N无缝钢管表面外折缺陷产生原因的分析

通过对鞍钢生产的部分批号V、N微合金强化无缝钢管及生产该钢管的原料连铸坯和连轧管坯的表面缺陷进行研究，分析了含V、N钢管表面外折缺陷的成因，提出了改善钢管表面质量的方法。采用改进后工艺生产的无缝管，其表面外折废品量大幅度降低。     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Erosion und Korrosion of metallischer Werkstoffe in feststoffhaltigen Wässern

Erosion and corrosion of metallic materials in particle containing aqueous solutions The combined effect and mutual influence, respectively, of erosion and corrosion of metallic materials in particle containing flows was investigated. Materials under investigation are carbon steel of different hardness levels, ferritic chromium steel, austenitic stainless steel and brass. Corrosive medium was deionized water, acid (pH 4.5), alkaline (pH 10) and chloride (3% NaCl) solution. Quartz particles were used as abrasive at various particle concentrations, grain sizes and flow velocities. For comparison, tests were performed with pure water and under conditions of idle corrosion. Mechanical or corrosive influences dominate depending on material and test conditions, in some cases, synergistic effects of both mechanisms cause an increased mass loss.     

Quality-Assurance Technology in Japan

A survey of the state of SQA in Japan finds that the situation is much like, but slightly different than, that in the US.