Phase equilibria in the Co-rich Co-Al-W-Ti quaternary system

We determined phase equilibria in the Co-rich Co-Al-W-Ti quaternary system at a temperature range between 900 °C and 1200 °C with a close attention to the thermodynamic stability of the γ′-Co₃(Al, W, Ti) (L1₂) phase, based on micro-structure observation and electron microprobe analysis on bulk alloy samples heat-treated for periods up to 2000 h. In the quaternary system the single phase field of γ′ extends from the Co-Ti binary edge to a composition of Co-5Al-8.5W-8Ti (in at.%) at 900 °C. At the tip of the single phase field, the γ′ phase is in equilibrium with the γ-Co (A1), Co₂AlTi (L2₁) and Co₃W (D0₁₉) phases. The constructed vertical section of phase diagram between Co-9.4Al-9.6W and Co-16.5Ti indicates that there is a narrow composition range around Co-4.5Al-5.4W-7.5Ti in which the γ single phase field exists at high temperatures above 1200 °C and two-phase of γ+γ′ is thermodynamically stable at low temperatures below 1100 °C.     

Effects of fermentation conditions and soybean peptide supplementation on hyaluronic acid production by Streptococcus thermophilus strain YIT 2084 in milk

To increase the hyaluronic acid (HA) yield from Streptococcus thermophilus YIT 2084, fermentation conditions (pH, temperature, agitation, aeration) were optimized in milk-based medium, and the effects of supplemental soybean peptides, which have different molecular weight distributions, were determined. HA production was enhanced to approximately 100 mg/l at pH 6.8 and 33–40 °C. Agitation speed and aeration rate slightly affected HA production. Soybean peptides including those of high molecular weight (approximately 27 to 130 kDa) further increased HA production to 208 mg/l under the optimal condition (pH 6.8, 35 °C, 100 rpm), which was 20-fold greater than non-optimal condition. HA production was no longer related to the specific growth rate. The HA produced under the optimal condition included a large amount of high-molecular-weight fraction of 100 to 2000 kDa, compared with under the basal condition without optimization.     

In-Flight Particle Measurement of Alkali-Free Glass Raw Materials in 12-Phase AC Arc Plasma

In-flight particle measurements of the surface temperature and velocity are important for understanding of melting behavior of glass particles during in-flight melting by multi-phase AC arc plasma. However, the use of optical pyrometry for particle surface temperature has inevitable uncertainties due to non-thermal emissions signals from the plasma plume. This work presents spectroscopic measurements of the non-thermal signals which were found to be caused mainly by the plasma emissions scattered by the particles and the radiation emitted by vapor. After that, the accuracy of thermal radiation measurement was estimated and surface temperature of in-flight glass particle was corrected.     

Thermomechanical characterization of β-stabilized Ti–45Al–7Nb–0.4W–0.15B alloy

The correlation between hot deformation parameters and the workability of β-stabilized Ti–45Al–7Nb–0.4W–0.15B (at. %) alloy was studied in the temperature range 1000–1200 °C and the strain rate range 0.001–1 s^?1. Deformation mechanisms were characterized by detailed analyses of the deformation behavior and microstructural observations. The results indicate that the deformation and recrystallization occurred preferentially in the grain boundary β phases because its good high temperature deformability enhances grain boundary sliding and migration, and thus improves the workability. Decomposition of the β phase to α₂ and γ phases partly accommodates the stress concentration and is thus beneficial in hot deformation. Appropriate deformation processing parameters were suggested based on the processing map, and were successfully applied in the quasi-isothermal canned forging of industrial-scale billets.     

Ionic liquid enables simple and rapid sample preparation of human culturing cells for scanning electron microscope analysis

Ionic liquid is a kind of salt that stays in a molten state even at room temperature. It does not vaporize at all in vacuum and facilitates electrical conductivity to the sample surfaces for observations with a scanning electron microscope (SEM). In this study, we used an ionic liquid in SEM for the first time to observe fixed human culture cells. The condition for the cell culture using wrapping sheets and SEM settings were varied to elucidate the optimized protocol. Compared to samples prepared by the conventional way, the ionic liquid‐treatment of samples gave SEM images of the cellular ultra structures in more detail, enabling observation of microvilli that made bridges between separated cells. In addition, the ionic liquid treatment is less time consuming as well as less laborious compared with the conventional way that includes dehydration, drying, and conductivity treatments. Totally, we concluded the ionic liquid is a useful reagent for SEM sample preparation. Microsc. Res. Tech., 2011. © 2010 Wiley‐Liss, Inc.     

电子装置内的热移动研究——温度分布及速度分布

在高60cm,宽45cm 的模拟电子装置内,进行装置内热移动研究,得到不同条件下的温度分布及速度分布.在理论解析及数值计算基础上,进行无因次准数关联,得出实验式.实验结果及解析结果基本一致.利用所得实验式对正在运转或有待开发的新的电子装置有关参数进行推算,对于传热设计具有很强的实用性.     

Two-wavelength laser diode interferometer with time-sharing sinusoidal phase modulation

We describe an interferometer system that uses two separate wavelengths to measure step height. The overlapping interference images detected by a CCD camera are easily separated by an ordinary integrating-bucket method and time-sharing sinusoidal phase modulation, in which two laser diodes are alternately modulated with a sinusoidal signal. A phase map is obtained only for the laser diode into which the modulation signal is injected. In this instance, a 1-microm step height was accurately detected.     

Surface modification of an organosilane self-assembled monolayer on silicon substrates using atomic force microscopy: scanning probe electrochemistry toward nanolithography

Organosilane self-assembled monolayers (SAMs) have been applied to resist materials for nanolithography based on scanning probe microscopy. An organosilane SAM was prepared on Si substrates from a precursor, that is octadecyltrimethoxysilane. Using an atomic force microscope with a conductive probe, current was injected from the probe into the SAM-covered Si substrate so that the SAM was locally degraded at the probe-contacting point. Nanoscale patterns drawn on the SAM was clearly imaged by lateral force microscopy. The patterning could be conducted in air while, in vacuum at the order of 10(-6) Torr, no detectable patterns were fabricated. The presence of adsorbed water at the probe/sample junction was confirmed to be crucial for the patterning of the SAM/Si. Its mechanism was, thus, ascribed to electrochemical reactions of both the SAM and Si with adsorbed water.     

Fast incremental learning methods inspired by biological learning behavior

Model-based learning systems such as neural networks usually “forget” learned skills due to incremental learning of new instances. This is because the modification of a parameter interferes with old memories. Therefore, to avoid forgetting, incremental learning processes in these learning systems must include relearning of old instances. The relearning process, however, is time-consuming. We present two types of incremental learning method designed to achieve quick adaptation with low resources. One approach is to use a sleep phase to provide time for learning. The other one involves a “meta-learning module” that acquires learning skills through experience. The system carries out “reactive modification” of parameters not only to memorize new instances, but also to avoid forgetting old memories using a meta-learning module.This work was presented, in part, at the 9th International Symposium on Artificial Life and Robotics, Oita, Japan, January 28–30, 2004