EPR study of hydrogen-related defects in boron-doped p-type CVD homoepitaxial diamond films

Boron-doped p-type single crystalline chemical vapor deposition (CVD) homoepitaxial diamond films were investigated by electron paramagnetic resonance (EPR). Carbon dangling bond defects, which were accompanied by a nearby hydrogen atom, were observed in boron-doped p-type CVD diamond films on a IIa substrate similar to those observed in undoped diamond. This result suggested that the energy level position of the defects is located below the Fermi energy of boron-doped diamond, at around 0.3 eV above the valence-band top. The reason why the Fermi energy could be changed by the incorporation of boron atoms at low density (10¹⁶–10¹⁷/cm³) in the film in spite of the existence of the large defect density of EPR centers (10¹⁸/cm³) is thought to be that the singly occupied electron states of defects are located near the band edge. As for the thermal annealing effect of the defects, it was revealed that the concentration of the defects and the mobility of the p-type film did not change after annealing up to 1200 °C which is much higher than the temperature of boron–hydrogen pair dissociation.     

Critical temperature for production of MAG by esterification of different FA with glycerol using <Emphasis Type="Italic">Penicillium camembertii</Emphasis> lipase

Production of MAG by a lipase-catalyzed reaction is known to be effective at low temperature. This phenomenon can be explained by assuming that synthesized MAG are excluded from the reaction system because MAG, which have low m.p., are solidified at low temperatures. Consequently, MAG are efficiently accumulated and do not serve as the precursor of DAG. If this hypothesis is correct, the critical temperature for MAG production, defined as the highest temperature at which DAG synthesis is repressed, should depend on the m.p. of the MAG. Esterification of FFA with glycerol using Candida rugosa, Rhizopus oryzae, and Penicillium camembertii lipases produced MAG efficiently at low temperatures. However, Candida lipase showed very low esterification activity at high temperatures (>20°C), and Rhizopus lipase produced not only MAG but also DAG even at low temperatures. Meanwhile, P. camembertii lipase catalyzed synthesis of MAG only from FFA and glycerol at low temperatures, although the enzyme catalyzed synthesis of DAG from MAG in addition to synthesis of MAG at high temperatures. We thus studied the effect of temperature on esterification of C₁₀−C₁₈ FFA with glycerol using Penicillium lipase as a catalyst and determined the critical temperatures for production of MAG. The critical temperature for production of each MAG showed a linear correlation with m.p. of the MAG, which supported the hypothesis. In addition, because the m.p. of MAG are estimated from that of the constituent FA, the optimal temperature for production of MAG can be predicted from the m.p. of the FFA used as a substrate.     

Stereochemistry and mechanism of the hydrogenation of dialkyl cyclohexenes

In order to investigate the steric effect of the substituents to determine the product distribution, disubstituted cyclohexenes were hydrogenated over several transition metal catalysts. Some cyclohexenes which have two large substituents at the vicinal carbon atoms, at least one of which is trigonal, were not hydrogenated over Raney Ni at all but were hydrogenated over Pt catalyst under our experimental conditions. Presumably, the stereoselectivity depends on the competitive operation of the torsional angle strain and the catalyst hindrance with substituents. In the hydrogenation over Pd catalyst, thermodynamically more stable products were dominant at the standard condition but at high substrate to catalyst ratio the less stable products were slightly preferred. No appreciable stereoselectivity was observed in the hydrogenation of 1,4-disubstituted cyclohexenes.     

Reaction and diffusion of reactive disperse dye in nylon 6

The diffusion of a reactive disperse dye with a vinylsulfonyl group accompanied by simultaneous reaction with the amino end groups in nylon 6 was examined by the method of cylindrical film roll at 70°C and pH 2.2–8.0. The experimental diffusion profiles of the active and fixed species of the dye in nylon 6 were confirmed to be described by the diffusion equation accompanied by the chemical reaction with substrate taking the limited amount of the end groups into account, where the active species of dye were assumed to react only with the free base of amino end groups. The completion of the reaction with the amino end groups was observed in the first layer from the surface at pH 6.0–8.0. The value of diffusion coefficient was constant (8.0 × 10^?10 cm²/s) at all the pH's. The product of the second-order rate constant, k₂, of reaction of the dye and the dissociation constant, K_a, of the amino end groups was constant (k₂K_a = 4.0 × 10^?9 s^?1) at pH 2.2–8.0. The k₂ values of the reaction with various substrates for vinylsulfonyl and monochlorotriazinyl-reactive dyes were compared and the practical dyeing conditions were discussed.     

Synthesis of γ-Ga2O3–Al2O3 Solid Solutions by the Glycothermal Method

The reaction of mixtures of aluminum isopropoxide and gallium acetylacetonate in 1,4-butanediol or 1,5-pentanediol at high temperatures (glycothermal reaction) directly gave the γ-Ga₂O₃–Al₂O₃ solid solutions, which had high catalytic activities for selective reduction of NO using methane as the reducing agent. However, the reaction with a higher Al/(Ga+Al) charged ratio yielded the glycol derivative of boehmite as a by-product and the catalytic activity of the solid solution decreased. Therefore, synthesis of the solid solution using various glycols was examined and it was found that solid solutions with high Al contents without contamination of the glycol derivative of boehmite were obtained by using 1,6-hexanediol as a reaction medium. The solid solution exhibited a higher NO conversion than that synthesized in other glycols.     

Characteristic properties of cutting fluid additives derived from the adducts of diamines and acid chlorides

A number of N,N′-diacylalkyldiamines were prepared from the reaction of acid chlorides with 1,8-diaminooctane and 1,12-diaminododecane and screened for anti-rust properties and antimicrobial activity in spent coolants of water-based cutting fluids. Aqueous solutions of N,N′-dihexanoyl-1,8-diaminooctane and N,N′-isobutyroyl-1,12-diaminododecane showed good anti-rust properties for water-based cutting fluids. Aqueous emulsions of N,N′-dibutyroyl-, dipentanoyl-, dihexanoyl- and dioctanoyl-1,12-diaminododecane showed good lubricities and antimicrobial activity for water-based cutting fluids.     

Development of a high‐resolution RGBW flexible display using a white organic light‐emitting diode with microcavity structure and that of a side‐roll touch panel

In this study, white organic electroluminescent devices with microcavity structures were developed. A flexible high‐resolution active‐matrix organic light‐emitting diode display with low power consumption using red, green, blue, and white sub‐pixels formed by a color‐filter method was fabricated. In addition, a side‐roll touch display was developed in combination with a capacitive flexible touch screen.     

Hydrothermal Formation of Hydroxyapatite Layers on the Surface of Type-A Zeolite

Type-A zeolite evenly covered with hydroxyapatite thin layers was prepared using hydrothermal treatment at 120°C for 8 h under autogenous pressure. The hydroxyapatite needlelike nanocrystals, 100–200 nm in diameter and 30 nm in thickness, were grown under the reaction between discharged Ca²⁺ ions from type-A zeolite and PO₄³⁻ ions in (NH₄)₃PO₄ solution. The preferential orientations of the c -axis of hydroxyapatite crystals perpendicular to a zeolite surface were observed using transmission electron microscopy. The crystal structure of type-A zeolite was not destroyed under the reaction, but the surface morphology was changed only with complete covering of scaly hydroxyapatite particles.     

Radiation-induced polymerization of ethylene in pilot plant. III. Heavy-phase recycling process

Radiation-induced polymerization of ethylene using aqueous tert-butyl alcohol as medium was carried out in a large-scale pilot plant with a 50-liter central source-type reactor at a pressure of 105 to 395 kg/cm², temperature of 30° to 80°C, mean dose rate of 4.5 × 10⁴ to 1.9 × 10⁵ rads/hr, ethylene feed rate of 5.5 to 23.5 kg/hr, and medium feed rate of 21 to 102 l./hr. The space–time yield and molecular weight of the polymer were in the range of 4.7 to 16.8 g/l.-hr and 1.3 × 10⁴ to 8.9 × 10⁴, respectively. The space–time yield and molecular weight increased with mean residence time at 30°C, whereas at 80°C they became almost independent of the time. The space–time yield increased with pressure and dose rate, slightly decreased with temperature, and was maximum at ethylene molar fraction of 0.5. The polymer molecular weight increased with pressure and ethylene molar fraction, and decreased with dose rate and temperature. The total amount of deposited polymer on the reactor wall, source case wall, and scraping blades was usually less than 1 kg, which was negligibly small for the analysis of polymerization. Continuous discharge of the polymer slurry and production of fine-powder polyethylene were successfully carried out. In the central source-type reactor, a dose rate of 1.9 × 10⁵ rads/hr was obtained with a ⁶⁰Co source of ca. 12 kCi.     

Radical polymerization of methyl methacrylate with some 1,2-disubstituted tetraphenylethanes as thermal iniferters

Summary The bulk polymerization of methyl methacrylate (MMA) with 1,2-disubstituted tetraphenylethanes, tetraphenylsuccinodinitrile (TPSN), tetra(p-methoxyphenyl)succinodinitrile (TMPSN), and pentaphenylethane (PPE), was investigated. These compounds were found to serve as thermal iniferters to induce living radical polymerization via a mechanism close to the model proposed previously (see Eq. 2). However, the living nature was not so high, because undesirable side reactions occurred. The oligomer with molecular weight of 2500 was isolated from the reaction mixture of MMA with TPSN, which was found to cause further polymerization of MMA. From the polymerization of styrene (St) with the polymers obtained by these iniferters, the block copolymers were produced.