Characterization of n-hexadecylalkylamine-intercalated graphite oxides as sorbents

Adsorption properties of graphite oxides hydrophobized by n-hexadecylamine, (C16)_xGO, were investigated using pyrene molecules as a model of nonionic organic contaminants. A large quantity of pyrene (28.5 mg/g) was adsorbed from a water-ethanol mixture (1:2) containing 2 mM of pyrene when (C16)_0.6GO was used. The isotherm of pyrene adsorption was better described by Freundlich equation rather than Langmuir equation, which indicated a single adsorption mechanism was involved. The change in the amount of adsorbed pyrene as a function of amine content in GO was very similar to that which occurs upon introduction of pyrene into (C16)_xGO films from chloroform solution, as determined by X-ray measurements. This suggests that pyrene molecules were adsorbed not only on the outer surface but also within the interlayer space of the intercalation compound. Swelling of the intercalation compound by ethanol can render the interlayers more organophilic and make access to hexadecylamine molecules bonded to the graphite oxide layer easier for pyrene molecules, especially in (C16)_xGOs with lower amine contents.     

Determination of fatty acid composition by gas chromatography: II. Analysis with use of flame ionization detector

In this study known mixtures of four or five fatty acid methyl esters were analyzed collaboratively by gas chromatography with flame ionization detectors. The experimental data was treated statistically to examine inter- and intralaboratory scattering. More-over the effect of the use of correction factors was investigated. Even if only the specific analytical values that scattered a little were chosen, the averages of such values did not always approach the actual values. In some laboratories a sort of regularity was observed in the deviation of analytical values from real values throughout the analyses of four samples. The application of correction factors to the analytical values obtained by these laboratories resulted in a considerable decrease of interlaboratory scattering and deviation from the real values. When a constant amount of sample was injected, intralaboratory scattering was decreased, whereas interlaboratory scattering was not. Injection of large sample sizes caused deviation. From this collaborative study it was recommended that 0.5–1.0 μl of 20% solution be injected. Presented at the JOCS-AOCS Joint Meeting, Los Angeles, April 1972.     

Drag reduction of aqueous suspensions of fine solid matter in pipe flows

It is well known that drag reduction properties of polymer solutions in pipe flows are classified into two categories, based on the relationship between the friction factor and the Reynolds number. The degree of drag reduction either increases with an increase in the Reynolds number or is independent of the Reynolds number. In the latter case, the drag reduction behavior is referred to as type B behavior. In this study, the pressure losses of aqueous suspensions of biofibers and graphene oxide flat particles in pipe flows were measured to clarify the effect of the shape of suspended fine solid matter on the friction factor. The experimental results demonstrated that the behavior of the friction factor corresponded with the type B behavior of drag reduction. The mean velocity profile in the range of the turbulent flow was also estimated from the friction factor data.     

Microstructures of functionally graded materials fabricated by centrifugal solid-particle andin-situ methods

Functionally graded materials (FGMs) belong to a relatively new class of inhomogeneous composite materials, in which the composition and/or microstructure undergo a gradual change along some directions. In this review article, the microstructures and composition gradients in Al/SiC, Al/Shirasu (volcanic eruptions commonly found in south Kyushu in Japan), Al/Al₃Ti, Al/Al₃Ni, Al/Al₂Cu FGMs have been investigated. The Al/SiC, Al/Shirasu and Al/Al₃Ti FGMs are fabricated by the centrifugal solid particle method where the distribution particles of SiC, Shirasu and Al₃Ti are solids in the melts. On the other hand, Al/Al₃Ni and Al/Al₂Cu FGMs are fabricated by the centrifugalin-situ method where Al/Al₃Ni and Al/Al₂Cu systems have lower liquidus temperatures than the processing temperatures. The feature of Al/(Al₃Ti−Al₃Ni) hydrid FGM, which is fabricated by a method combining both the centrifugal solid-particle andin-situ methods, is also shown.     

High-temperature oxidation of pure titanium in CO2 and Ar-10%CO2 atmospheres

The oxidation behavior of pure titanium has been investigated in the temperature range of 1000 K to 1300 K in CO₂ or Ar-10%CO₂. Optical microscopy, electron probe microanalyses, and X-ray measurements on the oxide scales formed during oxidation indicate that their structures are nearly independent of temperature and the corrosion atmosphere. The scales consisted of two layers, an external one and an internal one, having a rutile (TiO₂) structure. The parabolic rate law was confirmed for growth of the external scale and the permeation depth of oxygen in titanium with apparent activation energies of 266 and 226 kJ/mol, respectively. The rate-determining diffusion species in the oxidation processes are discussed.     

Probability of precision micro-machining of insulating Si3N4 ceramics by EDM

Electrical discharge machining (EDM) is used as a precision machining method for the electrically conductive hard materials with a soft electrode material. But recently we succeeded to machine on insulating material by EDM. The technology is named as an assisting electrode method. The EDMed surface is covered with the electrical conductive layer during discharge. The layer holds the electrical conductivity during discharge. For micro-EDM, the wear of tool electrode becomes lager ratio than the normal machining. So the micro-machining is extremely difficult to get the precision sample.

In this paper to obtain a fine and precise ceramics sample, some trials were carried out considering the EDM conditions, tool electrodes material and assisting electrode materials. Insulating Si₃N₄ ceramics were used for workpiece. The machining properties were estimated by the removal rate and tool wear ratio. To confirm the change of micro-machining process, the discharge waveforms were observed. The micro-machining of the Ø0.05 mm hole could be machined with the commercial sinking electrical discharge machine.     

Evolution of patinas on copper exposed in a suburban area

Copper plates were exposed under sheltered outdoor conditions for up to one year, starting in September 2001 in Musashino City, Tokyo, a suburban area. Following various periods of exposure, the patinas on the plates were characterized to investigate their evolution by using X-ray fluorescence analysis, X-ray diffraction, field emission scanning electron microscopy, and glow discharge optical emission spectroscopy. The difference in the roles of sulfur and chlorine in the early stages of copper patination were identified by analyzing the depth profiles of these two elements. Sulfur was found on top of the patina as cupric sulfates such as posnjakite (Cu₄SO₄(OH)₆ · H₂O) or brochantite (Cu₄SO₄(OH)₆). Brochantite appeared only after 12 months of exposure. In contrast, chlorine was found on the surface after only one month of exposure. It gradually penetrated the patina as the exposure period lengthened, forming copper chloride complexes. Chloride ions accumulated at the patina/copper interface, forming nantokite (CuCl), which promoted corrosion.     

Differences between corrosion products formed on copper exposed in Tokyo in summer and winter

We analyzed the copper corrosion products that formed during a month in summer and a month in winter at three sites in Tokyo using several analytical techniques. The X-ray diffraction patterns revealed that cuprite Cu₂O and posnjakite Cu₄SO₄(OH)₆·H₂O formed on copper exposed in summer. By contrast, only cuprite was found in winter exposed copper. The X-ray fluorescence results indicated that the amounts of sulfur and chlorine on the copper plates exposed in summer were much greater than those in winter. This could be explained by the change in particulate sulfate and sea salt concentrations. Depth profiling analysis by Auger electron spectroscopy revealed that the oxide layer formed in summer was thicker than that in winter. This difference in oxide layer thickness could have been due to the differences in temperature, relative humidity, and the amount of sulfur and chlorine on the copper plate.     

Measurement of self-diffusion coefficients in Li ionic conductors by using the short-lived radiotracer of 8Li

For the effective use of short-lived radioactive beams, soon to be available at the Tokai Radioactive Ion Accelerator Complex, the authors have developed a radiotracer method for diffusion studies in solids. The experimental test was performed by the measurement of the diffusion coefficients of Li in a sample of the compound βLiAl using an α-emitting radiotracer of ⁸Li (T_1/2=0.84 s). It was found that the time-dependent yields of the α particles from the diffusing ⁸Li that was initially implanted in the sample could be used as a measure of the diffusivity of the tracer in a nondestructive way. The method was applied to measure the self-diffusion coefficients of Li in βLiGa, and for investigating how the Li diffusion in the Li ionic conductors is affected by the concentration of atomic defects (i.e., the existence of the atomic vacancies of Li and the defects in Ga sites that are replaced by Li).     

IMPROVEMENT OF TYPE IV CRACKING RESISTANCE OF 9Cr HEAT RESISTING STEEL WELDMENT BY BORON ADDITION

Creep lives of high Cr ferritic heat resisting steel weldments decrease due to Type Ⅳ fracture, which occurs as a result of formation and growth of creep voids and cracks on grain boundaries in fine-grained heat affected zone (HAZ). Because boron is considered to suppress the coarsening of grain boundary precipitates and growth of creep voids, we have investigated the effect of boron addition on the creep properties of 9Cr steel weldments. Four kinds of 9Cr3WSCoVNb steels with boron content varying from 4.7×10-5 to 1.8×10-4 and with nitrogen as low as 2.0×10-5 were prepared. The steel plates were welded by gas tungsten arc welding and crept at 923K. It was found that the microstructures of HAZ were quite different from those of conventional high Cr steels such as P91 and P92, namely the fine-grained HAZ did not exist in the present steel weldments. Boron addition also has the effect to suppress coarsening of grain boundary carbides in HAZ during creep. As a result of these phenomena, the welded join