The microstructure of highly-oriented graphite tape prepared from mesophase pitch by melt-blowing

A highly-oriented continuous carbon/graphite tape was prepared from a coal tar-based mesophase pitch by melt-blowing using a slit type nozzle. The average thickness and width of tape were ca. 20 μm and 7.2 mm, respectively. The molten precursor pitch was continuously extruded through the slit nozzle to produce a pitch tape along the drawing direction. The tape was oxidized, carbonized and graphitized. The micro area X-ray diffraction revealed that the carbon layer planes were oriented parallel to the tape surface indicating a strong anisotropy. The orientation was greater in the tape drawing direction than in the tape width direction, and also in the center area than in the edge area. The mechanical properties were higher than those of conducting polymers, but lower than those of carbon fiber with lower elastic modulus grade.     

Self-dissolving micropile array tips for percutaneous administration of insulin

Two kinds of insulin were loaded into self-dissolving micropile array tip (following tip). Fully-loaded tip (f-tip) and partially-loaded tip (p-tip) were prepared using chondroitin sulfate for the percutaneous administration of insulin. One hundred micropiles were constructed on a 1.0 × 1.0 cm tip. The mean length of the micropile in a tip were 483.4 ± 4.7 μm for the f-tip and 492.6 ± 2.4 μm for the p-tip. The insulin content of the p-tip was 28.5% of that of the f-tip. The pharmacological efficiency of insulin loaded tip was evaluated in rat experiments by measuring their hypoglycemic effects. The maximum hypoglycemic effect of insulin was observed at 1.7 ± 0.2 h for the f-tip and 1.5 ± 0.2 h for the p-tip. Good dose-dependency was observed for the plasma glucose level vs. time curves. These results suggest the usefulness of p-tip as a percutaneous DDS of insulin.     

Nanosecond and femtosecond mass spectroscopic analysis of a molecular beam produced by the spray-jet technique

The spray-jet molecular beam apparatus enabled us to produce a molecular beam of non-volatile molecules under high vacuum from a sprayed mist of sample solutions. The apparatus has been used in spectroscopic studies and as a means of molecular beam deposition. We analyzed the molecular beam, consisting of non-volatile, solvent, and carrier-gas molecules, by using femtosecond- and nanosecond- laser mass spectroscopy. The information thus obtained provided insight into the molecular beam produced by the spray-jet technique.     

Experimental study of the flow in helical circular pipes: Torsion effect on the flow velocity and turbulence

An objective of the present paper is to experimentally clarify the torsion effect on the flow in helical circular pipes. We have made six helical circular pipes having different pitches and common non-dimensional curvature δ of about 0.1. The torsion parameter β0, which is defined by β0 = τ/（2δ）1/2 with non-dimensional torsion r, are taken to be 0.02, 0.45, 0.69, 1.01, 1.38 and 1.89 covering from small to very large pitch. The velocity distributions and the turbulence of the flow are measured using an X-type hot-wire anemometer in the range of the Reynolds number from 200 to 20000. The results obtained are summarized as follows： The mean secondary flow pattern in a cross section of the pipe changes from an ordinary twin-vortex type as is seen in a curved pipe without torsion （toroidal pipe） to a single vortex type after one of the twin-vortex gradually disappears as β0 increases. The circulation direction of the single vortex is the same as the direction of torsion of the pipe. The mean velocity distribution of the axial flow is similar to that of the toroidal pipe at small β0, but changes its shape as β0 increases, and attains the shape similar to that in a straight circular pipe when ,β0 = 1.89. It is also found that the critical Reynolds number, at which the flow shows a marginal behavior to turbulence, decreases as ,β0 increases for small ,β0, and then increases after taking a minimum at ,β0 ≈ 1.4 as ,β0 increases. The minimum of the critical Reynolds number experimentally obtained is about 400 at ,β0 ≈ 1.4.     

Hydrogen entry into Fe and high strength steels under simulated atmospheric corrosion

Electrochemical hydrogen permeation tests of Fe sheets under two cyclic corrosion test (CCT) conditions were performed to understand hydrogen entry behavior under atmospheric corrosions. Hydrogen entry into 1300 MPa-class high strength steels under two CCT conditions was also investigated using thermal desorption analysis. One CCT consisted of salt spray, dry and wet stages (Salt Spray CCT; SSCCT), and the other consisted of dry and wet stages after NaCl deposition (Dry–Wet CCT; DWCCT). The corrosion rates of Fe and the steels were almost constant under SSCCT and they decreased under DWCCT with time. Nevertheless, both CCTs resulted in increases in hydrogen permeation current and diffusible hydrogen content with time indicating enhancement of hydrogen entry. Corrosion current monitored by means of an atmospheric corrosion monitoring sensor consisting of Fe anode and Ag cathode decreased obviously under dry stage of the CCTs, whereas hydrogen permeation was high at the beginning of the dry stage. The discrepancy between hydrogen entry and corrosion rate indicates that the hydrogen entry is not directly controlled by corrosion rate. Increase in acidity of underlying rust layer with growth of rust layer monitored using a W/WO₃ electrode is considered to be one of the factors affecting the hydrogen entry efficiency.     

An integrated numerical simulator for thermal performance assessments of firefighters’ protective clothing

Research and development of firefighters’ protective clothing relies on a large number of fire disaster experiments in order to assess the thermal performance. It would be substantially advantageous to substitute a virtual numerical experiment for a real one in terms of time, cost and safety. The present article reports the development of an integrated numerical simulator that makes possible the estimation of burn injuries originating from fire disasters. In the simulator, a general-purpose computational fluid dynamics program computes the fluid flow and heat transfer in an in situ fire event, while a one-dimensional program calculates the radiative–conductive heat transfer through the clothing and human skin. A data interface combines the two simulations by loose coupling so as to give the real-time burn injury progress output. The predicted surface heat fluxes and burn degrees agree with experimental measurements reasonably well. Possible numerical error sources are discussed that call for potential improvements in the future.     

Full‐duplex analogue/digital data transmission using lasers coupled to GI fibre and its application

This paper describes a low‐cost version of a full‐duplex optical fibre analogue/digital data transmission link whose practical implementation is simplified by using a pair of laser diodes, each having a built‐in photodiode for monitoring the laser output power, and its application to vibration test data transmission. The transmission link sends digital data of up to 9600 bps in one direction, and analogue data of DC to 100 kHz and image data specified by an NTSC colour video signal in the opposite direction, all at the same time through one GI optical fibre. Being simple in configuration and stable against noise, this type of link has a variety of applications within factory, home and offices. Copyright © 2001 John Wiley & Sons, Ltd.     

Analysis of Large Non-linear Elastic Deformation of Fabrics

The effect of material non-linearity on large lateral deformations of fabrics structures was studied. Fixing the boundaries, the deformation under uniform internal pressure was analyzed by nonlinear FEM (Finite Element Method). Because non-linear elasticity was found in the tensile testing of fabrics, the non-linear tensile characteristic was also considered in the FEM. Some experiments were conducted under various fixed conditions and the displacement was measured by a laser displacement sensor. The calculated results considering the non linear tensile elasticity of materials were found to agree with the experimental ones. Thus the validity of the proposed calculation method was proven.