Growth of bubbles containing plasma in water by high-frequency irradiation

Plasma was generated in water by irradiation at high frequency of 13.56 MHz, and the behavior of bubbles including the plasma was observed by a high-speed camera. The generation pattern of the bubbles was classified into four types according to liquid temperature and supplied power. Conducting the simulation, the maximum temperature in the bubble was found to be from 3500 K to 4300 K, and the decomposition of water molecule occurred. The gas in the bubble was found to become high ratio of hydrogen. The phenomenon can be regarded as a film boiling of exceptionally high heat flux.     

LiErO2 formation on Er2O3 in static and natural convection lithium

Er₂O₃ is candidate material for insulating coating to prevent the magnetohydrodynamic (MHD) pressure drop in the self-cooled liquid Li blanket system. Although Er₂O₃ is stable material, detailed chemical behavior in liquid Li is not clear. Corrosion behavior of bulk Er₂O₃ in Li is investigated in static and flowing condition in the present study. After these tests, good compatibility of Er₂O₃ was confirmed and slight formation of LiErO₂ was detected by XRD analysis. This chemical behavior did not change in a static and flowing tests, however some of the corrosion product of LiErO₂ was removed easily by the Li flow. Intensity of LiErO₂ peaks in XRD spectrum suggests that the temperature gradient may affect the reaction rate in the natural convection loop. Since corrosion rate of Er₂O₃ is very small, slight change in state will be important information to evaluate lifetime of coating.     

A 65 nm Single-Chip Application and Dual-Mode Baseband Processor With Partial Clock Activation and IP-MMU

Supporting both WCDMA with HSDPA and GSM/GPRS/EDGE, the 9.3 times 9.3 mm² SoC fabricated in triple-Vth 65 nm CMOS, has three CPU cores and 20 separate power domains. Unused power domains can be powered down to reduce the leakage power. Partial clock activation scheme especially focused on music playback scene dynamically stops a PLL and clock trees when not necessary and reduces power consumption from 33.6 mW to 19.6 mW. IP-MMU translates virtual address to physical address for 18 hardware-IPs and virtual address space can be allocated when necessary and can be freed after its operation, reducing external memory by 43 MB. Video performance of D1 (720 times 520) size with 30 frames per second for MPEG/AVC decoding and encoding can be achieved under mixed virtual and physical address usage.     

Application of SPRT to an image data sequence for a remote monitoring system

Recently, remote monitoring camera systems have been widely used for security. In such systems, one important function is that the system automatically detects any change in the scenes from the monitoring cameras. In wireless remote monitoring camera systems, the images of the scenes are generally transmitted as compressed data (e.g., JPEG file), because of the capacity of the wireless channel. This article shows the automated detection of the change point in time-series data of compressed JPEG file quantity (Kbytes) from the monitoring camera by applying the sequential probabilistic ratio test (SPRT) and the Chow test, which is well known as a standard method for detecting structural change in time-series data.     

Coupling Analysis of GaAs-Based Microdisk Lasers With Different External Claddings

In this paper, we analyze the coupling of light from a GaAs microdisk laser into a waveguide. Starting from an air cladding, we examine several configurations to couple light into the waveguide with different cladding structures aimed to foster light coupling into the waveguide: photonic crystal and metallic (plasmonic cladding). In these coupling schemes, we tried to optimize the coupling of the emitted light into the waveguide, while maintaining a reasonable quality factor to allow the lasing operation of the device. We show that a plasmonic layer, introduced beside the waveguide can lead to a significant improvement in the coupling efficiency, reaching an efficiency close to 80%.     

Decay of material properties of degraded MEA caused by repeated cold starts under subzero conditions in polymer electrolyte fuel cells

This study investigated the characteristics of cell performance degradation, decline of component performance, and changes in the properties of membrane electrode assembly materials caused by repeated cold starts under a subzero condition of ?30 °C. It was made clear that functional decay appeared mainly at the cathode due to increased proton conductive impedance and reduction of reactivity of the electrode catalyst. Among the cathode components, an increase in proton conductive impedance in the cathode electrolyte was dominant. Furthermore, the application of ion chromatography and a newly developed proton‐induced gamma‐ray emission method to measure fluorine in the off‐gas drain revealed that decomposition of the electrolyte was dominant in the cathode catalyst layer. A decrease in fluorine in the cathode electrolyte measured by fluorine‐19 nuclear magnetic resonance confirmed this decomposition. A hypothesis is also presented concerning the cause of the performance degradation. © 2012 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.20394     

Self-flux synthesis and photoluminescent properties of LiAl5O8

Pure-phase LiAl₅O₈ was selected as an oxide ceramic red phosphor material without dopants (color centers) and was synthesized using a self-flux method. The LiAl₅O₈ was formed by heating a powder mixture consisting of γ-Al₂O₃:Li₂SO₄ = 1:2 (molar ratio) at over 1100 °C for 1 h. Photoluminescence (PL) properties for the synthesized LiAl₅O₈ were investigated. The maximum intensity of the excitation spectrum for the photoluminescent emission of LiAl₅O₈ synthesized was at 274 nm. The peak intensity of the emission spectrum was at a wavelength of 667 nm (red color). The intensity of the peak emission spectrum increased with the heating temperature, i.e., the maximum peak intensity of the red emission spectrum was detected for the LiAl₅O₈ synthesized by heating at 1500 °C for 1 h.