TRVs and fault clearing stresses in extra-high-voltage radial networks

To cope with the high rate of increase of power demand in the main industrialized districts in Japan, 550-kV transmission systems covering the districts have been reinforced, with most of the main power plants connected directly to these systems. Through 550-/300-kV substations, the majority of power to the districts is supplied by 300-kV systems. To limit the excess short-circuit capacity in the 300-kV systems, they tend to be reconstructed as so-called radial networks. In radial networks with high short-circuit capacity and relatively small number of transmission lines connected to the substation busbars, the rate of rise of TRV can be far higher than standard value. This paper analyzes the transient recovery voltages (TRV) in such extra-high-voltage radial networks in Japan, together with the relevant stresses to circuit-breakers during fault clearings. Future system conditions have also been introduced. As the typical rate of rise of the TRV values, more than twice that of today's standard ones are probable.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Fabrication of blue-light emission fused-silica substrates by using Si-ion implantation and high-temperature annealing

We fabricated fused-silica substrates which emit blue light by using Si-ion implantation and high-temperature annealing. Photoluminescence peak wavelengths are around 400 nm, and the peak intensities can be remarkable after annealing above 1150 °C.     

Twin-Related Tetragonal Variants in Yttria Partially Stabilized Zirconia

Crystals of yttria partially stabilized zirconia were grown by the arc-image floating-zone technique and studied by transmission electron microscopy. Crystals annealed at 1700°C consist of tetragonal precipitates and a cubic matrix. The platelike domains in a precipitate are twin-related tetragonal variants stacked alternately parallel to the (011) twin plane. The axial relations between the tetragonal precipitate and the cubic matrix are [100]_tetragonal|[100]_cubic, [011]_tetragonal|[011]_cubic.     

Titania NOx sensors for exhaust monitoring

Oxide semiconductors have been examined to develop NO_x sensors for exhaust monitoring. Titania doped with trivalent elements, such as Al³⁺, Sc³⁺, Ga³⁺ or In³⁺, has a good sensitivity and selectivity to NO between 450 and 550 °C, and shows rapid response. A sensor probe for monitoring exhaust NO_x has been fabricated. Many kinds of interference gases, such as C₃H₆, CO and SO₂, have been found to have only a slight influence on the sensor response to NO. The influence of O₂ and H₂O is also negligible, except for the cases of 0% H₂O and fuel-rich conditions. In accordance with these results, the sensor probe operates satisfactority in the exhaust gas of various combustion conditions without interference from the various kinds of gas species in the exhaust gases.     

Pseudo-binary system Bi2O3-TeO2 in air

The phase equilibria in the pseudo-binary system Bi₂O₃-TeO₂ at 600° 950° C in air were examined by solid-state reaction techniques and X-ray powder diffraction method. Four pseudo-binary compounds appeared, i.e., -Bi₂O₃ type solid solution having a compositional range of (1-x)Bi₂O₃·xTeO₂ wherex=0 0.4 a new compound Bi₆Te₂O₁₅ which has an orthorhombic cell of a=2.27(4) nm, b=1.06(1) nm and c = 0.539(8) nm, 2Bi₂O₃ · 3TeO₂, and an unidentified phase Bi₂O₃·2TeO₂. The formation of the phase Bi₆Te₂O₁₅, in which all the Te ions are hexavalent, was confirmed by the thermogravimetry and by the Mössbauer spectra. The liquidus curves for whole system were determined by DTA method.     

Effect of Silicon Dioxide on the Thermal Diffusivity of Aluminum Nitride Ceramics

The thermal diffusivity of AlN ceramics was significantly decreased by the addition of SiO₂. The AlN ceramics with 4 wt% SiO₂ could not be densified by pressureless sintering in the temperature range 1400° to 1800°C. The thermal diffusivity of these samples was very low because of their porous structure. The AlN ceramics containing 2, 4, and 8 wt% SiO₂ were densified by hot-pressing and also had low thermal diffusivity. In these samples, the grains of the 27R polytype that resulted from the reaction between AlN and SiO₂ were dispersed, obstructing the conduction of heat. The relation between the amount of 27R polytype and the thermal diffusivity of the AlN ceramics was determined.     

Reverse osmosis separation of hydrocarbons in aqueous solutions using porous cellulose acetate membranes

A physicochemical parameter, represented by the symbol Σs^*, based on molar solubility in water and molar attraction constants of Small, has been developed to express quantitatively the relative hydrophobicity, or nonpolar character, of the hydrocarbon molecule. The value of Σs^* can be calculated for a hydrocarbon from its chemical structure. The scale of Σs^* is consistent within each group of aromatic, cyclic, and noncyclic hydrocarbons. Reverse osmosis data have been obtained at 250 psig for single-solute aqueous feed solution systems involving low concentrations of 39 different hydrocarbons (including 13 aromatics, 10 cyclic, and 16 noncyclic compounds) and several samples of cellulose acetate membranes of different surface porosities. The effect of operating pressure on membrane performance has also been studied for two aromatic hydrocarbon solutes. The values of Σs^* for the solutes used were in the range of 425 to 924 for aromatic hydrocarbons, 521 to 931 for cyclic hydrocarbons, and 369 to 960 for noncyclic hydrocarbons. The reverse osmosis data have been correlated with Σs^* for each group of hydrocarbons studied. In all cases, positive solute separations were obtained, and the ratio [PR]/[PWP] was less than 1. With respect to each film, solute separation increased with increase in Σs^*, and decreased with increase in operating pressure. Also, solute separation decreased in the order aromatic hydrocarbon > cyclic hydrocarbon > noncyclic hydrocarbon at any given value of Σs^*. At a given operating pressure, for low values of Σs^* (～500 or less) solute separation increased with progressive decrease in average pore size on the membrane surface. For high values of Σs^* (～800 or more), solute separation initially increased with decrease in average pore size, then passed through a maximum and minimum with further decrease in average pore size, and again increased with still further decrease in average pore size. The results are discussed on the basis of preferential sorption of solute at the membrane–solution interface under the experimental conditions studied.     

Reverse osmosis separations of polyethylene glycols in dilute aqueous solutions using porous cellulose acetate membranes

Reverse osmosis separations of eight polyethylene glycol (PEG) solutes in the average molecular weight range of 200 to 6750 in single-solute dilute aqueous solutions have been studied using porous cellulose acetate membranes at the operating pressures of 50, 75, and 100 psig. Diffusivity data for the above PEG solutes have also been obtained from experimental data on intrinsic viscosities. From an analysis of all experimental data, numerical values for the parameters representing the polar (?ΔΔG/RT), steric (δ^*ΣE_s), and nonpolar (ω^*Σs^*) forces governing reverse osmosis separations of PEG solutes have been generated. These numerical values are useful for precise characterization of cellulose acetate membranes for whose specifications sodium chloride is not the appropriate reference solute because of its low or practically negligible separation under reverse osmosis operating conditions. This work also illustrates that solute separation in reverse osmosis can predictably increase or decrease with increase in operating pressure depending on experimental conditions.