An equation of state for 1,1-difluroethane (HFC 152a)

An equation of state for 1,1-difluoroethane (HFC 152a, CH₃CHF₂) has been developed on the basis of reliable experimental data including PVT, liquid C_p, and saturated-liquid-density data measured by our group. It is a non-dimensionalized virial equation whose functional form is the same as that originally developed for 1,1,1,2-tetrafluoroethane (HFC 134a) in our group. The effective range is for pressures up to 15 MPa, temperatures from 230 to 450 K, and densities to 1000 kg m⁻³. The equation represents reliable PVT measurements within ± 1% in pressure for the superheated vapour and supercritical fluid, while within ±0.5% in density for the compressed liquid. In addition, it should be noted that the equation represents the other essential thermodynamic properties including vapour pressures, saturated-liquid/ vapour densities, isobaric/isochoric specific heats and sound velocity in both the liquid and gaseous phase of HFC 152a.     

New balance ground relay for parallel four-circuit transmission lines

A 66-kV network generally is grounded through a neutral grounding resistor. In this network a single-phase ground-fault current is limited to as small as 100 to 400 A. There are parallel four-circuit transmission lines mounted on the same tower in the 66-kV network. In such transmission lines, the load and the fault currents could induce circulating current that flows through the lines. Since the circulating current has zero-phase-sequence and negative-phase-sequence components, it could cause unwanted operation of a balance ground relay using zero-phase-sequence current. However, it is difficult to compensate for the circulating current by the conventional vector compensation scheme. This paper presents a new balance ground relay to deal with the circulating current. In the relay from the ground-fault inception until first tripping, the difference current Δ3I_2d of negative-phase-sequence current 3I_2d of the differential current between two protected lines is used as an input current. The Δ3I_2d is the difference current of 3I_2d between, before and during faults. After the first tripping, the difference current of positive-phase-sequence load current and zero-phase-sequence current of the forementioned differential current are used as an input current. Consequently, a higher sensitivity of the ground-fault protection for these lines has been achieved. The correct operation of the new balance ground relay was confirmed when a single-phase-ground-fault occurred in the parallel four-circuit transmission lines, to which the relay is applied.     

The gamma-ray-induced crosslinking of polyacrylamide

The gamma-ray-induced crosslinking of polyacrylamide was carried out under various conditions. The molecular weight of the polymer before inrradiation was found to be the most important factor for crosslinking. When polymers have low molecular weights such as 80,000, the intensity of radiation, the external pressure applied, and the water content of the polymer powder became important for crosslinking. Although the polycrylamide hydrogel can be obtained directly by irradiating the monomer, it was obtained more conveniently by the irradiation of monomer—polymer mixtures. The hydrogels obtained by the radiation with a dose of over 50 kgray, absorb water by 1000–1500 wt %.     

TRVs and fault clearing stresses in extra-high-voltage radial networks

To cope with the high rate of increase of power demand in the main industrialized districts in Japan, 550-kV transmission systems covering the districts have been reinforced, with most of the main power plants connected directly to these systems. Through 550-/300-kV substations, the majority of power to the districts is supplied by 300-kV systems. To limit the excess short-circuit capacity in the 300-kV systems, they tend to be reconstructed as so-called radial networks. In radial networks with high short-circuit capacity and relatively small number of transmission lines connected to the substation busbars, the rate of rise of TRV can be far higher than standard value. This paper analyzes the transient recovery voltages (TRV) in such extra-high-voltage radial networks in Japan, together with the relevant stresses to circuit-breakers during fault clearings. Future system conditions have also been introduced. As the typical rate of rise of the TRV values, more than twice that of today's standard ones are probable.     

Characterization of calcium-independent cytosolic phospholipase A2 activity in the submucosal regions of rat stomach and small intestine

This study was undertaken to compare the calcium-independent phospholipase A₂ (PLA₂) activities in the cytosols of twelve rat tissues and to determine whether their activities were distinct. 1-O-Alk-1′-enyl-2-[¹⁴C]-oleoyl-sn-glycero-3-phosphocho-line (PlsC) and 1-O-Alk-1′-enyl-2-[¹⁴C]oleoyl-sn-glycero-3-phosphethanolamine (PlsE) were synthesized and used as substrates, instead of phosphatidyl compounds, to exclude hydrolysis by cytosolic PLA₁ activity that could be present in some of the cytosolic preparations. For each tissue, we examined substrate specificity, pH optimum, and effect of adenosine triphosphate (ATP) and ATP analogues. PLA₂ activity was detected in eleven out of the twelve issues examined. Based on substrate specificity and pH optimum, cytosolic calcium-independent PLA₂ were classified in three groups. The first group, which included PLA₂ from small intestine, stomach and spleen, had the highest specific activity with PlsC as substrate (1253, 309 and 75 nmol/mg protein/hour, respectively) and an optimal pH at 6.5. Activity with PlsE as substrate was much lower (20–37%) than with PlsC. The second group of PLA₂ activities included the cytosolic activities from thymus, lung, liver and pancreas that showed lower specific activities for both substrates (14–23 nmol/mg protein/hour with PlsC) and had a broader optimal pH range of 6.1 to 7.5. The cytosols from brain, kidney, heart and muscle comprised the third PLA₂ group that was found to have a higher specific activity with PlsE (5–20 nmol/mg protein/hour) than PlsC and an optimal pH range from 7.4 to 7.9. Since the highest specific activity was found in the cytosol from small intestine, this PLA₂ was examined further. PLA₂ activity was found to be equally distributed in the cytosol of the submucosal portion of duodenum, jejunum and ileum with an optimal pH of 6.1 and a 5-fold higher activity with PlsC than PlsE as substrate. Moreover, this PLA₂ activity was inhibited by treatment with detergents. These results indicate the presence in the submucosal portion of the intestine of a calcium-independent cytosolic PLA₂ with a high specific activity toward PlsC and properties distinct from those described for the PLA₂ found in the intestinal brush-border.     

Effect of surface-modifying macromolecules and solvent evaporation time on the performance of polyethersulfone membranes for the separation of chloroform/water mixtures by pervaporation

Polyethersulfone (PES) membranes using different evaporation periods were fabricated by the phase-inversion method. Pervaporation experiments were conducted for chloroform/water mixtures to determine the selectivity of the PES membranes. It was found that chloroform could be concentrated in the permeate from chloroform/water binary feed mixtures by PES membranes prepared using longer evaporation periods, and that the selectivity of PES membranes in pervaporation could be reversed by shorter evaporation periods. This study also showed that by adding surface-modifying macromolecules (SMM) up to 1 wt % into the casting solution, chloroform enrichment in the permeate could be increased by 50%. Chloroform enrichment increased with increasing SMM concentration until an optimal value, after which the enrichment decreased. © 1994 John Wiley & Sons, Inc.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Fabrication of blue-light emission fused-silica substrates by using Si-ion implantation and high-temperature annealing

We fabricated fused-silica substrates which emit blue light by using Si-ion implantation and high-temperature annealing. Photoluminescence peak wavelengths are around 400 nm, and the peak intensities can be remarkable after annealing above 1150 °C.     

Twin-Related Tetragonal Variants in Yttria Partially Stabilized Zirconia

Crystals of yttria partially stabilized zirconia were grown by the arc-image floating-zone technique and studied by transmission electron microscopy. Crystals annealed at 1700°C consist of tetragonal precipitates and a cubic matrix. The platelike domains in a precipitate are twin-related tetragonal variants stacked alternately parallel to the (011) twin plane. The axial relations between the tetragonal precipitate and the cubic matrix are [100]_tetragonal|[100]_cubic, [011]_tetragonal|[011]_cubic.