XPS analysis of CdS/CuInSe2 heterojunctions

CdS/CuInSe₂ (CIS) heterojunctions were investigated by XPS analysis. An In-excess layer which may form an ordered vacancy compound (OVC) was present at the as-deposited CIS surface and it remained after chemical bath deposition of a CdS layer. The In-excess layer was removed by preferential etching with NH₃ aqueous solution. This result implies that the surface of the as-deposited CIS film was converted from the OVC with n-type conductivity into the CIS with p-type by NH₃ treatment. The conduction band offsets at the CdS/p-CIS and CdS/n-OVC were determined to be 1.0 and 0.3 eV, respectively. The CIS solar cells fabricated with n-OVC surface layer exhibited higher cell efficiencies than those fabricated with p-CIS surface layer.     

A new blood compatible and permselective hollow fiber membrane for hemodialysis

The authors have prepared a blood compatible and highly permselective hemodialysis membrane composed of polyether segmented nylon. This block copolymer was synthesized by polycondensation of bis-3-aminopropyl-poly(tetramethylene oxide) (PTMO) and poly(imino-1,3-bismethyl-cyclohexyl-iminoisophtharoyl) (NyBl) prepolymer obtained by polycondensation of 1,3-bis(aminomethyl)cyclohexane (B) and isophthalic acid (I). The molecular weight (MW) calculated from the number of end-groups was 16,000-21,000. In vitro blood compatibility was evaluated in terms of platelet adhesion onto the surface. PTMO-NyBl surfaces showed excellent platelet adhesion preventing properties. The PTMO-NyBl hollow fiber membrane was obtained by a dry-wet spinning process. The membranes had higher permeability coefficients for macromolecules ranging from MW 10,000 to 20,000 than polysulfone hollow fiber membrane (PS membrane), and had acceptably low albumin permeability for use as a dialysis membrane. The ex vivo blood compatibilities of PTMO-NyBl membrane and PS membrane were investigated by extracorporeal circulation in a pig model. The PTMO-NyBl membrane gave excellent results when assessing hemodialysis leukopenia, oxidative burst, and free platelet count decrease.     

High performance 35 nm gate length CMOS with NO oxynitride gate dielectric and Ni salicide

The 35 nm gate length CMOS devices with oxynitride gate dielectric and Ni salicide have been fabricated to study the feasibility of higher performance operation. Nitrogen concentration in gate oxynitride was optimized to reduce gate current I/sub g/ and to prevent boron penetration in the pFET. The thermal budget in the middle of the line (MOL) process was reduced enough to realize shallower junction depth in the S/D extension regions and to suppress gate poly-Si depletion. Finally, the current drives of 676 /spl mu/A//spl mu/m in nFET and 272 /spl mu/A//spl mu/m in pFET at V/sub dd/=0.85 V (at I/sub off/=100 nA//spl mu/m) were achieved and they are the best values for 35 nm gate length CMOS reported to date.     

Channelling studies on the lattice location of B atoms in graphite

In order to obtain information on the lattice location of B atoms in graphite, channelling experiments have been performed at room temperature with a proton beam of an energy of 0.65-0.77 MeV for the 〈0 0 0 1〉 axial channel in highly oriented pyrolytic graphite (HOPG) crystals doped with 0.32 at.% B. The B atoms are detected by measuring α-particles which are emitted as a result of a nuclear reaction ¹¹B(p,α)αα. It is clearly demonstrated that most of B atoms are shadowed behind the 〈0 0 0 1〉 C atomic rows. Taking account of the already reported experimental results on a change of lattice parameters by B-doping, it is concluded that most of B atoms are located at substitutional sites. It is also observed that B-doping introduces lattice strain on the c-plane. In addition, the presence of a small portion of interstitial B atoms is suggested.     

Transmission Characteristics of Hybrid Modes in Corrugated Waveguides Above the Bragg Frequency

We studied the transmission characteristics of hybrid modes in a corrugated circular waveguide above the Bragg frequency to develop a broad-band transmission line for millimeter waves. Millimeter waves at 294 GHz were transmitted into a straight waveguide. From observed power profiles in waveguide cross-sections, a high attenuation rate of 0.13 dB/m was obtained. To match a theoretical attenuation constant with the experimental one, we introduced an ad hoc coefficient of conventional surface reactance in the waveguide wall. This was necessary because the wall began to look like the surface with a decreasing anisotropic reactance owing to the frequency above the Bragg frequency. Using nonlinear optimization for mode content analysis, the observed power profiles in the waveguide cross-section were matched with theoretical profiles. There was good agreement between the calculated and observed centers of power profiles and attenuation rate along the waveguide. The theoretical analysis showed that the magnetic field at the waveguide wall increases and the substantial attenuation takes place. Above the Bragg frequency coupling to backwards propagating modes is a point of consideration. A combination of the backwards propagating EH_1,26 and the forward propagating HE₁₁ modes satisfied the Bragg condition at 294.7 GHz which was the nearest frequency of operating frequency. A strong attenuation of the incoming HE₁₁ mode by Bragg resonance was not expected due to large difference of 0.7 GHz. It becomes clear that the observed high transmission loss outside of the Bragg resonance can be explained by a decrease in anisotropic surface reactance at the wall.     

Effect of conformational changes and differences of proteins on frictional properties of poly(vinyl alcohol) hydrogel

In this study, albumin or γ-globulin, both of which are included in natural synovial fluid, was used as an additive into lubricants to investigate the ability to reduce the friction for poly(vinyl alcohol) hydrogel in mixed lubrication. It was found from a measurement in circular dichroism that albumin contains a large amount of α-helix structure and γ-globulin contains a large amount of β-sheet structure. The lubricant containing only albumin showed low friction compared to the lubricant containing only γ-globulin. The effect of protein boundary film was clarified by changing lubricant. Albumin kept the friction low after changing from γ-globulin used at initial rubbing, but γ-globulin increased the friction after changing from albumin at initial rubbing. From a sliding distance of 600 m, albumin showed lower friction but γ-globulin showed higher friction. Therefore, in the case of friction decreasing, γ-globulin forms a tight adsorbed layer and subsequently albumin forms a layer with low shearing strength. Hence, it is important to apply the adsorption layer of γ-globulin at the bottom and make a layered structure composed of albumin and γ-globulin to reduce both friction and wear.     

Evaluation of cost reduction potential for 1 kW class SOFC stack production: Implications for SOFC technology scenario

Recently, a commercial version of a residential solid oxide fuel cell (SOFC) system with a flat tubular cell has been developed. However, the system cost still remains very high, which is a barrier to its widespread use. In this study, the potential for cost reductions in SOFC stack production was investigated in order to contribute to the viability of the widespread use of such residential SOFC systems in future. A cost analysis of 700 W SOFC stack production based on a process integration modeling was conducted. The present bottom–up approach enabled us to perform a sensitivity analysis with a variety of parameters in terms of cell design, the production process and cell performance. This allowed us to investigate the effects of these factors on the production cost, thereby revealing the quantitative impact of each technological improvement on the cost reduction potential. The present analysis also revealed innovation pathways which could result in technology scenarios where residential SOFC systems could reach a break-even point in comparison with the baseload electricity cost. The analysis of the cost reduction potential presented here provides a useful viewpoint for developing a research strategy for state-of-the-art SOFC technology.     

Organic LED full-color passive-matrix display

Abstract— A full-color 5.2-inch 1/4-VGA passive-matrix organic LED display has been developed, adopting selective deposition for the different emitting materials. The display features 320 (×3) × 240 pixels with an equivalent pixel size of 0.33 × 0.33 mm, white peak luminance of over 150 cd/m², and power consumption of 6 W.     

High-velocity impact experiment of aluminum foam sample using powder gun

Porous materials such as aluminum foam have been investigated for possible use as impact shock absorbers in transportation aeronautic applications. However, the response of aluminum foam during impacts at high velocities of more than 100 m/s is not yet fully understood. A high-velocity impact experiment was therefore carried out to clarify impact shock absorption properties of aluminum foam. A one-stage powder gun was used to accelerate an aluminum foam sample to impact a rigid wall. Velocity and deformation of the aluminum foam sample during impact was studied using a digital high-speed video camera, while the pressure wave in the aluminum foam sample was measured using a PVDF gauge. The experimental observations revealed uneven collapse of the aluminum foam sample structure during high speed impact with a general stress plateau effect, typical for cellular material structures when subjected to quasi-static loading.     

Experimental verification for stability improvement of sensorless vector control system of induction motor using real‐time tuning of observer gain

This paper proposes a method for the design of the adaptive rotor flux observer gain to improve stability at low speed and in regenerating mode. The method is based on stability analysis, which utilizes a linearized model considering all systems, including each control loop. Therefore, the proposed method considers the effects of motor constants and control circuit constants. The stability analysis using the transfer function for the rotor speed considers the arrangement of poles and zeros and the steady‐state error. The rotor flux observer gain which improves the stability for each operating condition is ascertained. This paper also proposes a real‐time tuning method for the observer gain. The validity of the proposed method was confirmed by simulation using Matlab Simulink and by experiment. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 166(1): 67–81, 2009; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20715