Properties of Va metal-B films prepared by r.f.-sputtering

Ta_100-x B _x alloy films were prepared by r.f.-sputtering in the chemical composition range 45 x 77. Ta_100-x B _x (45 x 58) films consist of the amorphous phase, while the TaB₂ crystal phase was observed in Ta_100-x B _x (66 x 77) films. A remarkable preferred orientation with the (001) plane of TaB₂ parallel to the film surface was observed in Ta₃₄B₆₆. The d.c. electrical conductivity of Ta_100-x B _x (45 x 77) films decreases with increasing boron content in the range 6.7 × 10³ to 1.3 × 10^3–1 cm^–1. The micro-Vickers hardness of Ta_100-x B _x (45 x 77) films was in the range 2200 to 2600 kg mm^–2.     

Preparation of Co-N films by rf-sputtering

Co-N films in the wide compositional range can be prepared by reactive sputtering. Co-N sputtered films consist of one or two phases, such as CoN, Co₂N, Co₃N, Co₄N and -Co. Co₄N phase with a cubic unit cell is observed, and its lattice constant isa = 0.3586 nm. The preferred orientation is observed on the Co-N films, CoN (200) plane, Co₄N (1 1 1) plane and -Co (002) plane parallel to the film surface, respectively. Saturation magnetization _s of Co-N sputtered film decreases from 160 to 1.7 e.m.u. g^–1 with increasing content of N from 0 to 21.7 at%, and coercive force_I H _c is the range of 43 to 5000e at room temperature.     

Stability of protective oxide films in waste incineration environment—solubility measurement of oxides in molten chlorides

Solubility measurements of several oxides in molten NaCl-KCl and NaCl-KCl-Na₂SO₄-K₂SO₄ were conducted in three different levels of basicity. The dissolution behavior of the oxides showed almost the same tendency as that shown by the dissolution behavior of the oxides in molten Na₂SO₄ in literature. In a waste incineration environment, a protective Cr₂O₃ film easily dissolves in molten chlorides as CrO₄²⁻ because pO²⁻ of the molten chlorides tends to have a small value due to the effect of water vapor contained in the combustion gas. From the result of the solubility measurement, the addition of molybdenum and/or silicon was expected to improve the corrosion resistance of alloys. Laboratory corrosion tests confirmed this expectation. However, the scale analysis suggested that the effect of molybdenum could not be explained completely by only the mechanism derived from the result of the solubility measurement.     

Development of flexible organic light‐emitting diode on barrier film and roll‐to‐roll manufacturing

To come out with a successful organic light‐emitting diode (OLED) lighting business, it is very important to have clear differentiation of OLED from LEDs. Flexible OLED has merits, such as capability to be mounted on the curved wall, which is not easy for LEDs to achieve the feature. There are several approaches to make flexible OLEDs especially among those plastic barrier films that can bring high level of flexibility, which could not be achieved by any conventional lighting method. In this paper, barrier films with various water vapor transmission rate values, including 10^{? 6} order, are applied, and the conditions to have almost no dark spot growth under 85 °C and 85% high temperature/humidity test are shown. Flexible OLED panels are manufactured with the world's first roll‐to‐roll equipment using plastic barrier film.     

Influence of ammonium salt on electrowinning of copper from ammoniacal alkaline solutions

In order to develop an energy-saving copper recycling process from wastes, electrochemical measurements were conducted in ammoniacal alkaline solutions containing Cu(I) ions and an ammonium salt of sulfate, chloride or nitrate. The results of each system were then compared. The polarization measurements suggested that the voltage required for the electrode process is lower in the chloride and nitrate systems than that in the sulfate system. The cathode current efficiency during the copper electrodeposition varied from 39 to 97% and increased with current density in the chloride and sulfate systems. In the nitrate system, the lowest cathode current efficiency of 30% was observed because of nitrate ion reduction. Based on these results, the power consumption required for the electrowinning stage of the copper recycling process was calculated. Among these three systems, the chloride system showed the lowest power consumption of 500 kWh t⁻¹ at the current density of 200 A m⁻², which is about 25% of the conventional copper electrowinning process from a copper sulfate-sulfuric acid solution.     

Some characteristics of a sparged agitated vessel under foaming — Mechanical control of foaming —

Foam-breaking with a rotating disk mechanical foam-breaker (MFRD) was studied for a foaming system containing a diluted detergent solution in a laboratory sparged agitated vessel. The change of the foam-breaking capacity of the MFRD by varying the air sparge rate, the working volume and the impeller speed or the disk diameter was measured. Based on these measurements, empirical equations are presented for predicting the critical foam-breaking regions of the MFRD fitted with the agitated vessel. The operational range where foam-breaking with the MFRD can be carried out effectively and economically is also discussed.     

Playful training with augmented reality games: case studies towards reality-oriented system design

In this paper, we propose a reality-oriented augmentation approach to support training activities. The approach aims at adding new value and playful features to traditional training environments with keeping their original look-and-feel. For example, a game monitoring service enables to automatically record game events so that players can review a gaming process and strategy for soul-searching, or replay most impressive scenes to share the experience with others after the game finishes. Even several services are running on background, digital devices and services are seamlessly integrated to the game environment in unobtrusive way so that players can concentrate on training as usual. The concept can be applied to both traditional games (e.g., poker and the game of Go) and non-gaming activities (e.g., calligraphy and drumming). We developed four case studies on the concept: Augmented Reality Go, EmoPoker, Augmented Calligraphy and AR Drum Kit. We discuss design issues in the reality-oriented augmentation process based on user study results.     

Evidence for a Jahn-Teller distortion of Cs2NaHoCl6 at 150 mK observed by X-ray diffractometry

By means of SR X-ray diffractometry, cooperative Jahn-Teller distortion as a structural phase transformation of the first kind is directly confirmed by a splitting of Laue spots. It is understood that the degenerate ground state of a nonmagnetic doublet (₃) of Ho³⁺ in a cubic Ho-elpasolite, Fm3m(O _h ⁵ ), at least above 600 mK, is lifted up by a distortion below 150 mK, which was predicted by a splitting of the NQR spectrum and anomalies in the specific heat and magnetic susceptibility. This structural transformation shows not only the lowest transition temperature up to now, but also the greatest hysteresis specified by a Schottky-type excitation. The magnitude of the relative distortion (1/1) has been roughly estimated to be on the 2.0 · 10^–3 order of magnitude, which is much larger than the predicted value obtained from a point charge approximation. The pecularities of this transition are discussed from the viewpoint that the general theory of a structural transformation, established convincingly at high temperatures could not be easily applied.     

Stick-slip motion control based on cutter location data for an orthogonal-type robot

In this article, a new desktop orthogonal-type robot, which has the capacity of stick-slip motion control based on cutter location data, is presented for lapping small metallic molds with a curved surface. The robot consists of three single-axis devices with a high position resolution of 1 μm. A thin wooden stick tool with a ball-end shape is attached to the tip of the z-axis. In order to improve the lapping performance, a novel stick-slip motion control method is developed in the control system. The small stick-slip motion is orthogonally generated in the direction of the tool’s movement. The effectiveness of stick-slip motion control is examined through an actual lapping test of an LED lens cavity.     

First-principles calculation of L10 -disorder phase equilibria for Fe–Ni system

By combining Cluster Variation Method with FLAPW electronic structure total energy calculations and the Debye–Grüneisen theory within quasi-harmonic approximation, L1₀-disorder phase equilibria for Fe–Ni system are calculated. The transition temperature, 483 K, determined in the present calculation is lower than that obtained in the previous calculation without thermal vibration effects. The decrease of the transition temperature is ascribed to the enhanced phase stability of a disordered phase due to the thermal softening of a lattice.