Effect of Ultrasonication on the Microstructure and Tensile Elongation of Zirconia-Dispersed Alumina Ceramics Prepared by Colloidal Processing

To obtain dense, fine-grained ceramics, fine particles and advanced powder processing, such as colloidal processing, are needed. Al₂O₃ and ZrO₂ particles are dispersed in colloidal suspensions by electrosteric repulsion because of polyelectrolyte absorbed on their surfaces. However, additional redispersion treatment such as ultrasonication is required to obtain dispersed suspensions because fine particles tend to agglomerate. The results demonstrate that ultrasonication is effective in improving particle dispersion in suspensions and producing a homogeneous fine microstructure of sintered materials. Superplastic tensile ductility is improved by ultrasonication in preparing suspensions because of the dense and homogeneous fine microstructure.     

Dynamic breakdown characteristics of liquid helium induced by aquench of superconducting wire and coil

For practical insulation design of superconducting power apparatus, it is necessary to take into account an inherent phenomenon known as quench, the transition from the superconducting to the normal state. We investigated quench-induced dynamic breakdown and prebreakdown characteristics of liquid helium (LHe). Experimental results revealed that the quench of the superconductor drastically reduced the breakdown voltage of LHe in the thermal bubble disturbance. Moreover, dynamic breakdown characteristics in a quasi-uniform field using a superconducting coil were investigated. The results revealed that the breakdown was induced in the quench-initiated region where the largest thermal energy was generated     

Thermal degradation characteristics of oil‐filled cable joint with extremely degraded tan δ oil

Much of oil‐filled (OF) cable has been used for a long time as 66‐ to 500‐kV extrahigh‐voltage cable. Sometimes we can see extremely degraded tan δ oil (several tens of percent of tan δ, for example) in joint boxes, etc. The values of tan δ calculated by a simple combination model of paper/oil show that the oil‐impregnated paper with such a high tan δ oil likewise has an extremely high tan δ, which must result in thermal breakdown. However, such an event has not taken place up to the present in actually operated transmission lines. This fact suggests that some mechanism for the suppression of tan δ has acted in the paper insulation impregnated with degraded tan δ oil. Therefore, we investigated in detail the tan δ characteristics of paper impregnated with extremely high tan δ oil. In addition, based on the investigation results, we developed a method for simulation of heat generation by dielectric loss in an OF cable joint (which has degraded tan δ oil). © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 178(1): 1–10, 2012; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21184     

Simultaneous removal of NO/sub x/, SO/sub x/, and CO/sub 2/ at elevated temperature using a plasma-chemical hybrid process

In previous studies, the authors confirmed that the plasma-chemical combined hybrid process for controlling NO flue gas emission was extremely effective and economical in comparison with the conventional selective catalytic reduction (SCR) system and other technologies. In the present study, we carried out experiments on the simultaneous removal of NO/sub x/ and SO/sub x/ at elevated temperature using the plasma-chemical hybrid process. A series of experiments was performed to quantify all the reaction byproducts such as N/sub 2/O, CO, HNO/sub 2/, HNO/sub 3/, NO/sub 3//sup -/, and SO/sub 4//sup -/ to evaluate the simultaneous NO/sub x/ and SO/sub x/ removal efficiency. The oxidation from NO to NO/sub 2/ without decreasing NO/sub x/ concentration (i.e., minimum reaction byproducts) and with least power consumption is the key for the optimum operation of the plasma reactor. The produced NO/sub 2/ was totally converted to N/sub 2/ and Na/sub 2/SO/sub 4/ with Na/sub 2/SO/sub 3/ or Na/sub 2/S with and without NaOH using the barrier-type packed-bed plasma reactor followed by the packed-column chemical reactor. The NO/sub 2/ reduction was more effective for Na/sub 2/S than Na/sub 2/SO/sub 3/ but produces H/sub 2/S with Na/sub 2/S. For both cases at least five times the stoichiometric amount of chemicals were required for complete NO/sub 2/ reduction. Nearly 100% of NO/sub x/ and SO /sub 2/ and 40% Of CO/sub 2/ simultaneous removal were achieved with less than 5 ppm of N/sub 2/O and CO. The operating cost was less than 1/4 the SCR process. The additional SO/sub 2/ treatment system can be eliminated.     

Partial discharge inception characteristics under butt gap condition in liquid nitrogen/ PPLP/sup /spl reg// composite insulation system for high temperature superconducting cable

The partial discharge (PD) inception characteristics are studied in liquid nitrogen (LN/sub 2/)/polypropylene laminated paper (PPLP/sup /spl reg//) composite insulation system for high temperature superconducting (HTS) cable. Experimental results revealed that the magnitude of the initial PD increased as the PD inception electric field strength was increased, because the injected energy increased. Initial PD was generated at the first and third quadrant of applied AC voltage phase. The probability of initial PD at the positive and negative voltage phase was almost the same. The reason is because liquid nitrogen is a nonpolar molecule and we used symmetric electrode configuration with uniform electric field distribution. Finally, it was pointed out that PD inception electric field strength (PDIE) depended on the volume of the butt gap because of the increasing probability of weak points of electrical insulation, and PDIE linearly decreased with increasing stressed volume of the butt gap in the log-log scale.     

Effect of texture on oxidation resistance of Ti3AlC2

Oxidation resistance of textured Ti₃AlC₂ ceramics was measured in the temperature range 1273–1573?K. It was found that the oxidation was markedly anisotropic and the samples exhibited a better oxidation resistance when tested along a direction transverse to the c-axis. This behavior was attributed to the rapid diffusion of Al within its basal planes to form a passivating Al₂O₃ scale and it respected Ellingham diagrams. The scales formed had different compositions depending on the testing direction; this response was clearly resulting from the crystallographic orientation. Even at 1473?K after 20?h exposure, the samples tested in a direction transverse to the c-axis showed a reduced weight gain which was 45 times lower than one seen on a basal plane.     

Rapid Reconstitution of Biosynthetic Machinery for Fungal Metabolites in Aspergillus oryzae: Total Biosynthesis of Aflatrem

Reconstitution of the biosynthetic machinery for fungal secondary metabolites in Aspergillus oryzae provides an opportunity both for stepwise determination of the biosynthetic pathways and the total biosynthesis of fungal natural products. However, to maximize the utility of the reconstitution system, a simple and rapid strategy for the introduction of heterologous genes into A. oryzae is required. In this study, we demonstrated an effective method for introducing multiple genes involved in the biosynthesis of fungal metabolites by using the expression vectors pUARA2 and pUSA2, each of which contains two cloning sites. The successful introduction of all the aflatrem biosynthetic genes (seven genes in total) after two rounds of transformation enabled the total biosynthesis of aflatrem. This rapid reconstitution strategy will facilitate the functional analysis of the biosynthetic machinery of fungal metabolites.     

Reduction and Sintering of a Nickel–Dispersed-Alumina Composite and Its Properties

High-density nickel–dispersed-alumina (Al₂O₃/nickel) composites with superior mechanical properties were obtained by the hydrogen reduction and the hot pressing of alumina–nickel oxide (Al₂O₃/NiO) mixed powders. The mixtures were prepared by using NiO or nickel nitrate (Ni(NO₃)₂· n H₂O) as a dispersion source of nickel metal. Microstructural investigations of the composite fabricated using nitrate powder revealed that fine nickel particles, } 100 nm in diameter, dispersed homogeneously at the matrix grain boundaries, forming the intergranular nanocomposite. High strength (.1 GPa) and high-temperature hardness were registered for the composite that contained a small amount of nickel dispersion. The ferromagnetic properties of nickel, such as high coercive force, were observed, because of the fine magnetic dispersions, which indicates a functional value of structural composites.     

Electrical and electroluminescent properties of poly(p-phenylene vinylene) LB films based LEDs using aluminum metal as the electrode

The electrical properties of poly(p-phenylene vinylene) (PPV) Langmuir-Blodgett (LB) films were investigated, wherein transparent indium-tin oxide (ITO) and aluminum (Al) were used as the electrodes. Their I–V characteristics depended strongly on the thickness of PPV LB film, and the electric conductivity of the PPV LB film was in the range of 10⁻²–10⁻¹⁵ (S/cm). Their C–V characteristics showed that the capacitance was reversibly proportional to the thickness of PPV LB film and was kept constant when the applied voltage changed from −1.0 V to +1.0 V. These results indicated that PPV LB film was an insulator in this range of applied voltage without doping. Under forward bias, yellow-green light emission was observed in PPV LB film based light emitting diodes (LEDs), the highest light emission reached more than 100 cd/m² in the case that PPV LB film was deposited for 80 layers, i.e. a ITO/PPV(80L)/Al device.