Optimal tradeoffs for location-based routing in large-scale ad hoc networks

Existing location-based routing protocols are not versatile enough for a large-scale ad hoc environment to simultaneously meet all of the requirements of scalability, bandwidth efficiency, energy efficiency, and quality-of-service routing. To remedy this deficiency, we propose an optimal tradeoff approach that: 1) constructs a hybrid routing protocol by combining well-known location-update schemes (i.e., proactive location updates within nodes' local regions and a distributed location service), and 2) derives its optimal configuration, in terms of location-update thresholds (both distance and time-based), to minimize the overall routing overhead. We also build a route-discovery scheme based on an Internet-like architecture, i.e., first querying the location of a destination, then applying a series of local-region routing until finding a complete route by aggregating the thus-found partial routes. To find the optimal thresholds for the hybrid protocol, we derive the costs associated with both location updates and route discovery as a function of location-update thresholds, assuming a random mobility model and a general distribution for route request arrivals. The problem of minimizing the total cost is then cast into a distributed optimization problem. We first prove that the total cost is a convex function of the thresholds, and then derive the optimal thresholds. Finally, we show, via simulation, that our analysis results indeed capture the real behavior.     

A single-chip storage LSI for home networks

Network direct attached storage (NDAS) is a network storage architecture that allows direct attachment of existing ATA/ATAPI devices to Ethernet without a separate server. Unlike other architectures such as NAS, SAN, and USB mass storage, no server computer intervenes between the storage and the client hosts. We describe an NDAS disk controller (NDC) amenable to low-cost single-chip implementation that processes a simplified L3/L4 protocol and converts commands between ATA/ATAPI and Ethernet, while the remaining complex tasks are performed by remote hosts. Unlike NAS architectures that use TCP/IP, NDAS uses a TCP-like lean protocol that lends itself well to high-performance hardware realization. Thanks to the simple NDAS architecture and protocol, an NDC implemented on a single 4 mm /spl times/ 4 mm chip in 0.18 /spl mu/m CMOS technology achieves a maximum throughput of 55 Mbytes/s on gigabit Ethernet, which is comparable to that of a high-performance disk locally attached to a host computer.     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

Solution of a multidimensional inverse radiation problem by means of mode reduction

The Karhunen–Loève Galerkin procedure is employed to solve an inverse radiation problem of determining the time‐varying strength of a heat source, which mimics flames in a furnace, from temperature measurements in three‐dimensional participating media where radiation and conduction occur simultaneously. The inverse radiation problem is solved through the minimization of a performance function, which is expressed by the sum of square residuals between calculated and observed temperature, using a conjugate gradient method. Through the Karhunen–Loève Galerkin procedure, one can represent the system dynamics with a minimum degree of freedom, and consequently the amount of computation required in the solution of the inverse problem is reduced drastically when the present technique is adopted. Copyright © 2004 John Wiley & Sons, Ltd.     

Adhesive element modelling and weighted static shape control of composite plates with piezoelectric actuator patches

A novel finite element model is presented for static and dynamic analysis of composite plates integrated with a laminated piezoelectric layer, a host laminated composite plate and an adhesive layer between them. A new adhesive element is developed which includes both peel and shear effects in the adhesive layer based on first‐order shear deformation plate theory. The thin adhesive layer between the piezoelectric layer and the host plate is modelled by assuming that it carries constant shear and peel strains throughout its thickness. In addition, a weighted static shape control scheme for finding the optimal voltage distribution for static shape control is given. By selecting different weighting matrices, a variety of items such as displacements, slopes, curvatures, strains and even generalized forces, can be included in finding the optimal actuating voltage for static shape control. The present model is validated by comparing with those results available in the literature. The numerical results show that the weighted linear least method can give a satisfactory voltage distribution to best match the desired shape. Copyright © 2004 John Wiley & Sons, Ltd.     

螺栓角钢钢节点的三维非线性有限元分析

对螺栓角钢钢节点半刚性连接采用非线性有限元分析方法 ,对连接中的主要构件的顶部、底部、腹板角钢、高强螺栓、梁翼缘、柱翼缘和柱翼缘加劲肋进行三维非线性有限元精细模拟 ,针对有无柱加劲肋、有无腹板角钢等几种连接的情况进行比较分析 ,探讨了螺栓角钢半刚性连接的受力性能。