Low Dielectric Polyimide/Fluorinated Ethylene Propylene (PI/FEP) Nanocomposite Film for High-Frequency Flexible Circuit Board Application

The low dielectric polymer films have drawn great attention to the application as the dielectric insulating materials in high-frequency circuit boards, while the weak adhesion to the copper foils and the poor processability resulted from the fluorinated or rigid structures limited their high-frequency application. In this work, the low dielectric and high adhesive polyimide/fluorinated ethylene propylene (PI/FEP) nanocomposite film for high-frequency flexible circuit board application is developed. It is indicated that the fluorocarbon surfactants can significantly improve the dispersion of FEP in PI substrate, and thus, the PI/FEP nanocomposite film exhibits excellent mechanical properties, including the tensile strength increases to 46.6 MPa and the elongation at the break increases to 13.7%. Importantly, at the high-frequency of 10 GHz, the 60 wt% FEP filled PI nanocomposite film displays an ultralow dielectric loss (0.006) and a reduced dielectric constant (2.69). In addition, the high-frequency flexible circuit board with the PI/FEP film as the dielectric insulating layer has a high peel strength of 0.75 N mm⁻¹, indicating this PI/FEP nanocomposite film can meet the requirements of the high-frequency flexible circuit board application.     

A Strategy of Liquid-Grafted Slippery Sponges with Simultaneously Enhanced Absorption and Desorption Performances for Crude Oil Spill Remediation

Crude oil spill accidents pose a worldwide environmental threat. Oleophilic and hydrophobic absorbents that can selectively absorb oil from water have shown promising application potential in oil spill remediation. Simultaneous optimization of the absorption and desorption speed of absorbents towards oil is highly desirable for their recyclable usage, but remains a great challenge, because these two properties are generally conflicting. Here, a facile and ingenious strategy is proposed to tackle the above challenge via surface modification of porous sponges with highly flexible linear polydimethylsiloxane (LPDMS) brushes. The LPDMS brushes feature liquid-like properties at room temperature owing to its extremely low glass transition temperature, and act as a covalently-grafted lubrication layer throughout the 3D network channels of the sponge, which can minimize contact angle hysteresis and reduce friction between oil and sponge channel. Compared to the prevalent cross-linked polydimethylsiloxane (CPDMS) modification strategy, sponges modified with LPDMS brushes not only shows significantly enhanced absorption speed, but also exhibits superior desorption dynamics towards viscous crude oils. The design strategy of slippery sponges with liquid-like molecules may open a new avenue for developing advanced absorbents with simultaneously enhanced absorption and desorption performances for liquid separation and purification applications.     

Highly Thermal Stable Polyimides Applied in Flexible Resistive Memory

Flexible memory devices are one of the most crucial elements in the wearable electronics. In this work, polyimides (PIs)-based flexible resistive memory devices with an excellent thermal and mechanical durability are demonstrated. Four kinds of functional PIs are derived from the heterocyclic diamines including 2,6-diaminodibenzo-p-dioxin (OODA) and 2,6-diaminothianthrene, and dianhydrides including 4,4′-(hexafluoroisopropylidene)diphthalic anhydride (6FDA) and 3,3′,4,4′-biphenyltetracarboxylic dianhydride. PI with diamine of OODA and dianhydride of 6FDA (PI(OODA_6FDA)) possesses outstanding thermal and mechanical properties with a high glass transition temperature of 352 °C, a low coefficient of thermal expansion of 28.1 ppm K⁻¹, and a high elongation at break of 10%. In addition, PI(OODA_6FDA)-based memory shows write-once-read-many behavior with a high on/off current ratio of 10⁶ and a stable data retention, attributed to the donor–acceptor charge transfer between the polymer chains. The retained current levels at a low resistive state can be observed even with thermal treatment at 200 °C for 24 h or 1000 times cyclic bending at a bending radius of 5 mm. These results demonstrate the potential of heterocyclic PIs for flexible resistive memory.     

Microstructural evolution and interfacial reactions between Ti and ZrO2/CaTiO3 composites

Various proportions of ZrO₂/CaTiO₃ powders were mixed and hot pressed at 1500°C/30 min for Ti casting. The hot-pressed ZrO₂/CaTiO₃ composites were reacted with pure Ti at 1700°C/10 min in Ar. The interfacial reaction between Ti and ZrO₂/CaTiO₃ composites was investigated through X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and energy-dispersive X-ray spectroscopy. The ZrO₂/CaTiO₃ composites with less than 10 vol.%, CaTiO₃, and a minor amount of residual TiO₂ were found. When the content of ZrO₂ was increased to larger than 10 vol.%, two Ca₂Zr₅Ti₂O₁₆ and CaZrTi₂O₇ phases appeared in the composites. The amount of CaTiO₃ and CaZrTi₂O₇ in the composites gradually decreased as the amount of ZrO₂ increased. When Ti came in contact with ZrO₂/CaTiO₃ composites with less than 10 vol.% ZrO₂, the resulting eutectic reaction produced a liquid phase and induced melting. When ZrO₂ was increased to more than 30 vol.% in the composites, Ca₂Zr₅Ti₂O₁₆ and CaZrTi₂O₇ changed completely to CaZrO₃, Ti₂O, CaO, and ZrO₂. With more than 30 vol.% ZrO₂, no other reaction phases occurred in the Ti side after contact with the ZrO₂/CaTiO₃ composites, which is conducive for producing ceramic composites for Ti casting applications.     

Correction to: Bismuth Yttrium Oxide (Bi3YO6), A New Electrode Material For Asymmetric Aqueous Supercapacitors

Journal of Inorganic and Organometallic Polymers and Materials - The original version of this article unfortunately contained mistakes. In line 9 of the abstract, 5% should read as 2%. The...     

电感耦合等离子体质谱法在青海某地区铌矿物化学物相分析中的应用

为了准确快捷有效地对青海某地区铌矿物进行化学物相分析研究,采用电感耦合等离子体质谱法测定各相态中的铌,建立了一套准确快速测定铌矿物化学物相的分析方法.通过对溶剂的选择,实现对易解石、黄绿石、铌钙矿、铌铁矿、钛铁金红石和分散相的分离与测定.物相分析试样以两份完成,一份在550～600℃的高温炉中焙烧,氟化铵溶解易解石中铌.另一份试样不经高温焙烧,用含氯化亚锡的盐酸溶解分散相中的铌;用含氢溴酸的氟化铵溶解易解石和黄绿石中的铌;用含氢氟酸的硫酸溶解铌钙矿中的铌;用含氢氟酸的盐酸溶解铌铁矿中的铌;用焦硫酸钾熔融提取钛铁金红石中的铌,最后用电感耦合等离子体质谱法(ICP-MS)测定以上各相态中铌的质量分数.在ICP-MS工作条件下连续7次测定样品空白,计算各铌相态的方法检出限(3S/N)分别为0.023、0.021、0.018、0.025、0.016、0.007μg·g-1.对7个铌矿物样品进行铌物相分析,做精密度和准确度试验,符合《地质矿产实验室测试质量管理规范》(DZ/T 0130.3—2006)的要求.     

二元复合体系驱替聚驱后剩余油作用机理研究

海上稠油油田在聚驱之后仍然会有很大一部分剩余油,而聚合物和表活剂组成的二元复合体系用来驱替聚驱后残留剩余油效果显著,为了在微观和宏观上进一步研究二元复合体系是如何动用聚驱后的剩余油,采取微观可视化实验、4层非均质岩心驱替实验、二维平面非均质岩心的驱油实验进行研究,通过结果分析得出二元复合体系可以有效地驱替簇状、柱状剩余油以及附着在岩壁表面的膜状剩余油,并且二元复合体系与油产生超低界面张力,其会动用一部分水驱和聚驱已波及到但无法采出的残余油,进而提高采收率.     

采用循环伏安法研究微孔型多孔炭电极的电容特性

以酚醛树脂为原料,KOH为活化剂,制备出3种不同孔径分布的微孔型多孔炭(孔径≤2 nm)。在低温氮气吸附法测定BET比表面积和孔结构的基础上,采用循环伏安法考察了这3种微孔型多孔炭作电极的双电层电容器(EDLC)的电容特性。实验结果表明,微孔型多孔炭作电极的EDLC的电容特性是:在低扫描速率下,其循环伏安曲线达到电容平台后在高电压(±1.0 V)附近出现峰电容;延长在电解液中的浸渍时间,电极的比电容增大,高电位附近的峰电容减小。3种不同孔径分布的微孔型多孔炭作电极的EDLC的循环伏安特性受浸渍时间影响的程度也不同。     

IF钢切边质量提升控制技术

针对 IF 钢经过连退或镀锌热处理,在切边过程中由于切边质量不佳,带钢边部容易产生毛刺等缺陷,进而影响带钢边部质量的问题,通过研究切边后带钢切断面各区域比例以及切边工艺参数对切边后切断面各区域比例的影响,对圆盘剪切边工艺参数进行了优化设计;同时通过研究去毛刺辊工作原理以及亮边缺陷产生原因,对去毛刺辊的涂层和底辊辊型进行了优化设计。采取优化措施后,IF 钢的切边质量得到了改善,并彻底消除了亮边缺陷。     

平板类气体辅助注射成型产品的CAE模拟研究

通过建立具有代表性的平板类气体辅助注射成型产品模型,借助注塑成型CAE软件Moldflow对该模型进行了一系列分析模拟。通过对模拟结果数据的综合分析和数学处理,得到了气体注射参数对气道穿透长度的影响规律、气体注射参数设置及气道穿透长度预测公式。