Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Feedback control of decoupled bending and torsional vibrations of flexible beams

In this article, we consider a flexible beam with a rigid body, of which the bending vibration and the torsional vibration are decoupled. Therefore we need two control motors to suppress the vibrations. Each set of dynamic equations is treated in the form of an appropriate Hilbert space. A stabilizing feedback control law of each rotation motor will be established on the basis of modal analysis. A set of experiments has been carried out, and the results demonstrate the effectiveness of the dynamic model and the proposed control law. © 1994 John Wiley & Sons, Inc.     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.     

Determination of horseradish peroxidase concentration using the chemiluminescence of Cypridina luciferin analogue, 2-methyl-6-(p-methoxyphenyl)-3,7-dihydroimidazo[1,2-a]pyrazin-3-one

The chemiluminescence of the Cypridina luciferin analogue, 2-methyl-6-(p-methoxyphenyl)-3,7-dihydroimidazo[1,2-a]pyrazin++ +-3-one (MCLA) was observed at 462 nm in the presence of horseradish peroxidase (HRP) and the total spectrum of light emitted was found to depend linearly on HRP concentration. Methods for the determination of HRP concentration using the chemiluminescence was investigated. HRP could be detected in the range from 100 pmol/L to 100 nmol/L under the optimum condition, H2O2 (10 mmol/L) and MCLA (10 mumol/L) at pH 5.8.     

Continual conversion of free fatty acid in rice bran oil to triacylglycerol by immobilized lipase

Rice bran oil containing 30–50% free fatty acid was continually converted to an oil containing more than 75% of triacylglycerol (TG) by means of immobilized lipase. The reaction was carried out at 60°C for 24 h with dehydration and reactant mixing by dry nitrogen flow under a positive nitrogen atmosphere. Enzymatic TG synthesis with evaporation by heating was not suitable because of the increasing peroxide value of the oil. Part of this article was presented at the annual meeting of the Japan Oil Chemists' Society at Sendai, Japan, October, 16, 1990.     

Antioxidizing component,musizin, inrumex japonicus houtt

A substance with antioxidant properties was obtained from the hexane extract of roots ofRumex japonicus Houtt. The active component of the hexane extract was isolated and characterized as 2-acetyl-1,8-dihydroxy-3-methyl naphthalene, trivially named musizin (MUS). The antioxidant activities of MUS in six types of fats and oils were higher than that of butyl hydroxyanisole (BHA) and δ-tocopherol (δ-TOC). Together, TOC and MUS have a synergistic effect, because comparable amounts of either had lower antioxidant activity than various combinations of the two antioxidants. When we studied the antioxidant properties of a mixture of MUS and δ-TOC with methyl linoleate (MeLH), we found that the rates of destruction of the two antioxidants were comparable, but that their destruction occurred sequentially, with MUS first followed by δ-TOC, after which the oxidation of MeLH quickly occurred. Comparison of the antioxidant activity of MUS and its analogs suggests that only one of the two hydroxyl groups in MUS is involved in its antioxidant activit. Intermolecular hydrogen bonding may be involved.     

Excitations bound to a vortex line in layered superconductors

Using Bogoliubov-de Gennes equation, we study quasiparticle excitations in layered superconductors in the presence of a straight vortex line which is parallel to the layers. The lowest bound state is shown to have energy eigenvalue of the order of magnitude , the energy gap, in contrast to the corresponding value ²/E_F when the line is perpendicular to the layers.     

A combined approach for modeling particle behavior in granular impact damper using discrete element method and cellular automata

A particle impact damper is a vibration absorber type that consists of a container attached to a primary vibrating structure. It also contains many particles that are constrained to move inside the container, whereby the damping effect can be obtained by collision between particles and the container. The discrete element method (DEM) has been developed for modeling granular systems, where the kinematics of each particle are calculated numerically using the equations of motion. However, the computational time is significant since the algorithm checks for particle contacts for all possible particle combinations. The use of a cellular automata (CA) modeling technique may provide increased computational efficiency due to the local updating of variables, and the discrete treatment of time and space. In this study, we propose a new approach combining DEM with CA for modeling a granular damper under a forced excitation. We use DEM to describe the particle motion according to the equations of motion, while CA is introduced for the particle contact checks in discrete space. We also investigate the effect of simplification in the contact force model, which allows the unit time step of numerical integration to become larger than that used in the strict model. It is shown that the suggested particle contact scanning method and the force approximation model contribute to the reduction of the computational time, and neither degenerates the calculation accuracy nor causes the numerical instability.