Iron Loss Calculation of AC Filter Inductor for Three‐Phase PWM Inverters

In recent years, remarkable advancement of new power semiconductor devices, such as SiC and GaN, enables the increase of switching frequency of power converters, and hence the volume of passive components, such as ac filters and transformers, can be reduced. However, temperature rise caused by the inductor loss is increasing, and hence iron loss evaluation of the inductor is one of the most important issues to realize high power density converters. Conventionally, an improved generalized Steinmetz equation (iGSE) has proposed in order to calculate the iron loss under a pulse voltage magnetizing condition. However, accurate iron loss calculation of the ac filter inductor used in a PWM inverter cannot be realized. The authors have proposed two methods of iron loss evaluation of ac filter inductors. The first one is a loss map method which can calculate the iron loss without using a real PWM inverter. Another one is an ILA (Inductor Loss Analyzer) which can measure the iron loss in every switching period in a real PWM inverter. In this paper, comparisons of the iron loss between the ILA and the loss map method on both the single‐phase and three‐phase inverters are studied. It is found that iron loss of the ac filter inductor in the three‐phase PWM inverter which is calculated by the loss map method cause a large error on a specific condition. In order to prevent the calculation error, the authors proposed a revised loss map method and proved the effectiveness of the method.     

Electrokinetic microslit experiments to analyse the charge formation at solid/liquid interfaces

Electrokinetic effects play an important role in microfluidics and nanofluidics. Although the related phenomena are often utilized to control fluid flow and sample transport in lab-on-a-chip devices, their dependency on the surface charges on the channel walls often remain enigmatic. This is mainly due to the lack of adequate experimental methods to analyse the electrical charging of solid/liquid interfaces of interest. To address this need, an experimental set-up—designated as microslit electrokinetic set-up (MES)—has been recently developed and applied for the investigation of charge formation processes at planar solid/liquid interfaces. The device permits to perform streaming potential and streaming current measurements across a rectangular streaming channel formed by two parallel sample carriers (20×10×3 mm³) at variable distance allowing for the determination of the surface conductivity. Utilizing the MES, charge characteristics can be determined for a wide variety of materials prepared as thin films on top of planar glass substrates. Streaming potential and streaming current data permit to investigate the mechanisms of charge formation while surface conductivity data provide information about mobile charge carriers located in different zones at the interface. The applicability of this advanced experimental approach is demonstrated with examples obtained for surfaces with different levels of complexity:

1. Preferential ion adsorption onto unpolar fluoropolymer (Teflon^® AF) films was characterized in simple electrolyte solutions; the results were quantitatively evaluated with respect to interfacial ion concentrations.
2. Interrelation of charge density and conformation of grafted poly(L-glutamic acid layers) were unravelled from the determination of pH-depended variations of surface conductivity and layer thickness.
3. The impact of spatial confinements of surface functional groups on their acid–base behaviour was studied with self-assembled monomolecular films of alkanethiols chemisorbed on gold.
4. Charging of and ion mobility within poly(acrylic acid) (PAA) brushes prepared by a Langmuir–Blodgett technique were analysed at varied pH and ionic strength.
5. Interfacial modes of adsorbed proteins were distinguished at two polymer surfaces with varied hydrophobicity/charge density.

     

Comparisons of optimal release policies for software systems

In a software product management, it is an important problem to determine the optimal release timing which minimizes the total expected cost incurred in both testing and operation phases. In this paper, we compare the performance between two kinds of software release methods, which are referred to as the T-policy and the N-policy. Based on the existing software reliability growth models, we formulate the expected cost functions and derive analytically the optimal policies under these control methods. Also, we derive a criterion for which control methods should be adopted. Finally, in numerical examples, we calculate the optimal release policies for several cost parameters.     

A small three-way valve using particle excitation with piezoelectric transducers for hydraulic actuators

Abstract

Robots composed of hydraulic actuators have been utilized in various fields and at disaster sites. However, the hydraulic control system for multiple-degree-of-freedom mechanisms is large because such systems require many control components. The purpose of this research was to develop a small hydraulic flow control valve. This paper describes the fabrication and evaluation of a small three-way valve by particle excitation using a piezoelectric transducer. This valve consists of two transducers and can switch the inlet and outlet ports by applying an AC voltage of different driving frequencies to each transducer because each transducer has different resonant frequencies. The flow rate was controlled by applying a voltage to the piezoelectric transducer. We evaluated the vibration characteristics of the fabricated three-way valve. The vibration velocity exhibited peaks at 120 and 155 kHz for the inlet and outlet port, respectively, and that of each transducer increased with the applied voltage. Therefore, this three-way valve can switch the opening port by changing the driving frequencies and continuously controlling the flow rate. As a result, we have succeeded in driving the novel small three-way valve.     

Smoking prevalence of female nurses in the national hospitals of Japan

OBJECTIVE: To estimate the prevalence of smoking and the attitudes towards the restriction of smoking at work among female nurses in the national hospitals in Japan. DESIGN: Questionnaires mailed to 14 randomly selected national hospitals and sanitariums in Japan in 1993. SUBJECTS: 2207 female nurses. MAIN OUTCOME MEASURES: Smoking status and history, and attitudes towards the restriction of smoking at work. RESULTS: The prevalence of smoking among female nurses was 18.6%, which was higher than the age-adjusted prevalence of the general female population using this study's subjects as a standardised population. Banning smoking in the hospital in which they worked was supported by 15.0%, whereas 81.6% supported the restriction of smoking. CONCLUSIONS: The results showed that smoking is more common among female nurses than among the general female adult population. The survey suggested that nurses favour restriction, but not banning, of smoking.     

Optimal periodic maintenance strategy under an intermittently used environment

In this paper, the optimal periodic replacement-like strategy with minimal repairs is considered under an intermittently used environment. Suppose that transactions or jobs with exponential service times arrive at a system according to a homogeneous Poisson process and the system is alternatively in either a busy or an idle period subject to demand for use. We derive approximately the optimal preventive maintenance schedule which minimizes the relevant expected cost criterion for the system which behaves intermittently on an M/M/1 queueing process, and compare it with the usual maintenance schedule for the continuously used system.     

Output power leveling of wind turbine generators using pitch angle control for all operating regions in wind farm

Effective utilization of renewable energies such as wind energy instead of fossil fuels is desirable. Wind energy is not constant and windmill output is proportional to the cube of the wind speed, which causes the generated power of wind turbine generators (WTGs) to fluctuate. In order to reduce the output power fluctuation of wind farms, this paper presents an output power leveling control strategy for a wind farm based on both the average wind farm output power and the standard deviation of the wind farm output power, a cooperative control strategy for WTGs, and pitch angle control using a generalized predictive controller (GPC) in all WTG operating regions. Simulation results using an actual detailed model for wind farm systems show the effectiveness of the proposed method. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 158(4): 31– 41, 2007; Published online in Wiley InterScience ( www.interscience. wiley.com ). DOI 10.1002/eej.20448     

Oxidation behavior of ytterbium silicide

Si-rich ytterbium silicide was fabricated by through an arc-melting technique for applying use as a bond coat material in an environmental barrier coating system. Evaluation of its potential was accomplished through oxidation tests in dry air and an inert atmosphere. The experimental results showed that the changes in weight and morphologies of ytterbium silicide observed after the tests depended on the oxygen partial pressure. Extensive oxidation and weight gain occurred after oxidation in air. In order to apply this material for hot structures, improvement of the oxidation resistance is needed.     

Fundamental welding R&D results for manufacturing vacuum vessel of JT-60SA

The real vacuum vessel (VV) manufacturing of JT-60SA has started since November 2009 at Toshiba. Prior to starting manufacturing, fundamental welding R&Ds had been performed by three stages. In the first stage, primary tests for screening welding method were performed. In the second stage, the trial welding for 1 m-long straight and curved double shell samples were conducted. The dependences of welding quality and distortion on the welding conditions, such as arc voltage and current, setting accuracy, welding sequence, and the shape of grooves were studied. In addition, welding condition with low heat input was explored. In the last stage, fabrication sequence was confirmed and established by the trial manufacturing of the 20° upper half mock-up [1]. This paper presents the R&D results obtained in the first and second stages.     

Analysis of lightning surge propagation in wind farm

Wind power generation is expected to become more important in future distribution systems. Although several prospective reports such as IEC 61400‐24 and NREL SR‐500‐31115 indicate an insulation scheme and grounding design for lighting protection, there still seems to be too few investigations on the problems. This paper therefore discusses lightning surge analysis using a wind farm model with 2 or 10 ideal wind turbines. Changing parameters such as grounding resistance and lightning strike points, several cases were studied. As a result of the analysis using digital simulator ARENE, it is clear that the surge tends to propagate toward the end of a distribution line in a wind farm and there is the possibility of insulation accidents at the other wind turbines when lightning attacks a wind turbine. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 162(2): 30– 38, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20364