Improvement of sensing characteristics of self‐sensing active magnetic bearings

A winding‐current interference model of self‐sensing magnetic bearings (AMBs) and an improvement technique of position‐sensing characteristics are proposed. In the self‐sensing AMB systems, the electromagnets work not only as actuators suspending the rotor but also as position sensors. The self‐sensing position signal, however, includes errors because of nonlinearity of the magnetic circuits. In the proposed model, the current is directly transmitted to the self‐sensing position signal. This transmission means degradation of the self‐sensing characteristics. This winding‐current interference to the self‐sensing signal is reduced by the proposed compensation method. The characteristics of the proposed self‐sensing method agree well with a reference sensor signal up to over 1 kHz. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 166(2): 70– 77, 2009; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20732 Copyright © 2004 Wiley Periodicals, Inc.     

Solid-state diffusion bonding of silicon nitride using titanium foils

This article presents an effective way to control the interfacial reaction during solid-state diffusion bonding of silicon nitride (Si₃N₄) using titanium foils. The interfacial structure and its growth kinetics were analyzed in detail with scanning electron microscopy (SEM), electron-probe microanalysis (EPMA), and X-ray diffraction (XRD). The actual phase sequence of the joint interfaces bonded at temperatures between 1473 and 1673 K is concluded to be Si₃N₄/Ti₅Si₃(N)/α-Ti(N)+Ti₅Si₃(N), which is different from the phase sequence observed at room temperature after bonding. The joints are very weak due to the formation of a brittle Ti₅Si₃(N) layer at the interface. To suppress the growth of the Ti₅Si₃ layer, a nitrogen-solution treatment of titanium foils prior to each bonding experiment is implemented. Although a perfect prevention of the Ti₅Si₃(N) layer formation is not achieved with this treatment, it is shown that the growth of the layer is effectively suppressed enough to improve the joint strength to a level 3 times higher than the case in which pure titanium is employed.     

Neurogenous tumors in head and neck region]

Detoxification of cyclophosphamide is effected, in part, by hepatic class 1 aldehyde dehydrogenase (ALDH-1)-catalyzed oxidation of aldophosphamide, a pivotal aldehyde intermediate, to the nontoxic metabolite, carboxyphosphamide. This enzyme is found in erythrocytes as well. Detoxification of aldophosphamide may also be effected by enzymes, viz. certain aldo-keto reductases, that catalyze the reduction of aldophosphamide to alcophosphamide. Such enzymes are also found in erythrocytes. Not known at the onset of this investigation was whether the contribution of erythrocyte ALDH-1 and/or aldo-keto reductases to the overall systemic detoxification of circulating aldophosphamide is significant. Thus, NAD-linked oxidation and NADPH-linked reduction of aldophosphamide catalyzed by relevant erythrocyte enzymes were quantified. ALDH-1-catalyzed oxidation of aldophosphamide (160 microM) to carboxyphosphamide occurred at a mean (+/- SD) rate of 5.0 +/- 1.4 atmol/min/rbc (red blood cell). Aldo-keto reductase-catalyzed reduction of aldophosphamide (160 microM) to alcophosphamide occurred at a much slower rate, viz. 0.3 +/- 0.2 atmol/min/rbc. Thus, at a pharmacologically relevant concentration of aldophosphamide, viz. 1 microM, estimated aggregate erythrocyte ALDH-1-catalyzed aldophosphamide oxidation, viz. 2.0 micromol/min, was only about 3% of estimated aggregate hepatic enzyme-catalyzed aldophosphamide oxidation, viz. 72 micromol/min; however, this rate is greater than the estimated flow-limited rate of aldophosphamide delivery to the liver by the blood, viz. 1.5 micromol/min. These observations/considerations suggest an important in vivo role for erythrocyte ALDH-1 in systemic aldophosphamide detoxification. Erythrocyte ALDH-1-effected oxidation of other aldehydes to their corresponding acids, e.g. retinaldehyde to retinoic acid, may also be of pharmacological and/or physiological significance since a wide variety of aldehydes are known to be substrates for ALDH-1.     

Highly Stretchable,Global, and Distributed Local Strain Sensing Line Using GaInSn Electrodes for Wearable Electronics

For identifying human or finger movement, it is necessary to sense subtle movements at multiple points, including the local strain and global deformation simultaneously; however, this has not yet been realized. Therefore, a highly stretchable, global, and distributed local strain sensing electrode made of GaInSn and polydimethylsiloxane is developed for wearable devices. To investigate the electrical properties of multiple sections of the GaInSn electrode when stretching, tensile, cyclic, and three‐point‐bending tests are performed. The results demonstrate that the electrode can withstand a strain up to 50% and has little hysteresis without any delay. Moreover, the distributed local strain and global strain can be simultaneously measured using just a single electrode line. Finally, a prototype of a data glove as an application of the strain sensing line is manufactured, and it is demonstrated that the folding state of fingers could be identified. The proposed technology may allow the creation of a lightweight master hand manipulator or 3D data entry device.     

Surface structure and visible light photocatalytic activity of titanium–calcium hydroxyapatite modified with Cr(III)

The synthetic titanium–calcium hydroxyapatite (Ti–CaHap) particles were treated with different concentrations of aqueous Cr(NO₃)₃·9H₂O solution and the materials obtained were characterized by a variety of conventional techniques. The crystal structure and particle morphology of Ti–CaHap were essentially not altered by treating with Cr(III) solution. With increasing the Cr(III) concentration, the amount of Cr(III) in the products was increased and that of Ca(II) was decreased. XPS results revealed that the surface state of Cr of Ti–CaHap was trivalent. These facts allow us to infer that the Cr(III) was doped by substitution of surface Ca(II) of Ti–CaHap. Besides, IR results proved that increasing the Cr(III) concentration developed the surface Cr–OH band while the surface Ti–OH and P–OH bands of Ti–CaHap vanished. This imply that the formation of surface P–O-Cr(OH)₂ and Ti–O–Cr(OH)₂ groups, resulting the Cr(OH)₃-like layer on the surface of Ti–CaHap particles. The Cr(III)-doped Ti–CaHap possessed the absorption peaks at 446 and 623 nm in vis range in addition to the UV absorption of charge transfer transition of O^2? → Ti⁴⁺. The vis absorption peaks developed on raising the Cr(III) concentration. The photocatalytic decomposition of acetaldehyde into CO₂ over Cr(III)-doped Ti–CaHap was detected under vis irradiation and the activity was lowered by the formation of Cr(OH)₃-like layer on the particle surface.     

Effect of catch cup geometry on 3D boundary layer flow over the wafer surface in a spin coating

Recently, development of high technology has been required for the formation of thin uniform film in manufacturing processes of semiconductor as the semiconductor instruments become more sophisticated. Spin coating is usually used for spreading photoresist on a wafer surface. However, since rotating speed of the disk is very high in spin coating, the dropped photoresist scarers outward and reattaches on the film surface. A catch cup is set up outside the wafer in spin coating, and scattered photoresist mist is removed from the wafer edge by the exhaust flow generated at the gap between the wafer edge and the catch cup. In the dry process of a spin coating, it is a serious concern that the film thickness increases near the wafer edge in the case of low rotating speed. The purpose of this study is to make clear the effect of the catch cup geometry on the 3D boundary layer flow over the wafer surface and the drying rate of liquid film.     

Numerical study on particle motions in swirling flows in a cyclone separator

The purpose of this study is to establish the high-accurate prediction method of particle separation in a cyclone separator. Numerical simulation of the swirling flows in a cyclone separator is performed by using a large eddy simulation (LES) based on a Smagorinsky model. The validity of the simulation and the complicated flow characteristics are discussed by comparison with experimental results. Moreover, particle motions are treated by a Lagrangian method and are calculated with a one-way method. A performance for particle separation is predicted from the results of the particle tracing. As results of our investigation, the influences of the inserted height of the outlet pipe on the performance for particle separation of cyclone separator are shown.