Electrophoretic deposition of graphene oxide on carbon brush as bioanode for microbial fuel cell operated with real wastewater

Microbial fuel cell (MFC) is a promising technology for simultaneous wastewater treatment and energy harvesting. The properties of the anode material play a critical role in the performance of the MFC. In this study, graphene oxide was prepared by a modified hummer's method. A thin layer of graphene oxide was incorporated on the carbon brush using an electrophoretic technique. The deoxygenated graphene oxide formed on the surface of the carbon brush (RGO-CB) was investigated as a bio-anode in MFC operated with real wastewater. The performance of the MFC using the RGO-CB was compared with that using plain carbon brush anode (PCB). Results showed that electrophoretic deposition of graphene oxide on the surface of carbon brush significantly enhanced the performance of the MFC, where the power density increased more than 10 times (from 33 mWm^?2 to 381 mWm^?2). Although the COD removal was nearly similar for the two MFCs, i.e., with PCB and RGO-CB; the columbic efficiency significantly increased in the case of RGO-CB anode. The improved performance in the case of the modified electrode was related to the role of the graphene in improving the electron transfer from the microorganism to the anode surface, as confirmed from the electrochemical impedance spectroscopy measurements.     

Heat propagation in thermally conductive polymers of PA6 and hexagonal boron nitride

Thermally conductive polymers offer new possibilities for the heat dissipation in electric and electronic components, for example, by a three‐dimensional shaping of the heat sinks. To face safety regulations, improved fire performance of those components is required. In contrast to unfilled polymers, those materials exhibit an entirely different thermal behavior. To investigate the flammability, a phosphorus flame retardant was incorporated into thermally conductive composites of polyamide 6 and hexagonal boron nitride. The flame retardant decreased the thermal conductivity only slightly. However, the burning behavior changed significantly, due to a different heat propagation, which was investigated using a thermographic camera. An optimum content of hexagonal boron nitride for a sufficient thermal conductivity and fire performance was found between 20 and 30 vol%. The improvement of the fire performance was due to a faster heat release out of the pyrolysis zone and an earlier decomposition of the flame retardant. For higher contents of hexagonal boron nitride, the heat was spread faster within the part, promoting an earlier ignition and increasing the decomposition rate of the flame retardant.     

Influence of ZrB2 hard ceramic reinforcement on mechanical and wear properties of aluminum

In this work, the effect of ZrB₂ (0, 5, 10 and 20?vol%) ceramic reinforcement on densification, structure, and properties of mechanically alloyed Al was investigated. The milling of Al-ZrB₂ powder compositions resulted in formation of agglomerates with varied size. In particular, the size of agglomerates was reduced considerably with increased addition of ZrB₂ to Al. Interestingly, the densification of hot pressed Al increased from 96.06% to 99.22% with ZrB₂ addition. The reduction of agglomerates size was attributed to the enhanced densification of Al-ZrB₂ composites. Pure Al showed relatively low hardness (0.94?GPa) and it was improved to 1.78?GPa with the addition of 20?vol% ZrB₂. The mechanical properties have significantly been improved for Al-ZrB₂ composites. Especially Al - 20?vol% ZrB₂ possessed a very high yield strength (529?MPa), compressive strength (630?MPa) and compressive strain of 19.25%. Realization of such a good combination of mechanical properties is the highest ever reported for Al composites so far in the literature. The coefficient of friction (COF) of Al-ZrB₂ varied narrowly between 0.33 and 0.40 after dry sliding wear against steel disc. The wear rate of Al-ZrB₂ composites was within mild wear regime and varied between 98.88?×?10^?6 and 34.66?×?10^?6 mm³/Nm. Among all the compositions, Al - 20?vol% ZrB₂ composite exhibited the lowest wear rate and high wear rate was noted for pure Al. Mild abrasion, tribo-oxidation, third body wear (wear debris) and delamination were the major material removal mechanisms for Al-ZrB₂ composites. Overall the hardness, strength and wear resistance of Al - 20?vol% ZrB₂ composite was improved by 84.3%, 84.3% and 64.2%, respectively when compared to pure Al.     

Determination of the Quadrupole Splitting in Bulk n-GaAs by Warm-Up Spectroscopy

Semiconductors - We found bulk n-GaAs layers grown by liquid phase epitaxy to be irregularly stressed. Deformation created by this stress causes a small but detectable quadrupole splitting of...     

Calculation of the Ephemeris and Clock Corrections of GLONASS and GPS Navigation Space Vehicles in Ultra-Rapid Regime on the Basis of Measurement Data

Measurement Techniques - An algorithm and program for calculation in ultra-rapid regime of the ephemeris and time information of GLONASS and GPS navigation space vehicles are developed. The results...     

Steels for Bridge Structures

Metallurgist - We consider domestic and foreign standards for rolled metals used in bridge building. Domestic standards contain elevated requirements to the reliability of rolled metals in terms of...     

A Dynamic Inertial Weight Strategy in Micro PSO for Swarm Robots

Wireless Personal Communications - A relatively new area of research and development is Swarm Robotics. It is a part of the swarm intelligence field. In the proposed paper, we shall use swarm...     

The Electron–Phonon Interaction of Low-Dimensional and Multi-Dimensional Materials from He Atom Scattering

Atom scattering is becoming recognized as a sensitive probe of the electron–phonon interaction parameter λ at metal and metal-overlayer surfaces. Here, the theory is developed, linking λ to the thermal attenuation of atom scattering spectra (in particular, the Debye–Waller factor), to conducting materials of different dimensions, from quasi-1D systems such as W(110):H(1 × 1) and Bi(114), to quasi-2D layered chalcogenides, and high-dimensional surfaces such as quasicrystalline 2ML-Ba(0001)/Cu(001) and d-AlNiCo(00001). Values of λ obtained using He atoms compare favorably with known values for the bulk materials. The corresponding analysis indicates in addition, the number of layers contributing to the electron–phonon interaction, which is measured in an atom surface collision.     

Investigation into the Influence of Sodium Lignosulfonate,Anionic Surfactants,and Their Mixtures on the Copper Cementation Rate by Zinc

Russian Journal of Non-Ferrous Metals - This article is devoted to the influence of sodium lignosulfonate (SL), anionic surfactants (sodium dodecylsulfate (SDS), sodium dodecylbenzene sulfonate...     

Collective reflection strategy for moderating conformity tendency and promoting reflective judgment performance

Reflective judgement is crucial for medical-related practitioners in dealing with controversial issues. However, the conformity phenomenon is likely to occur and interfere with reflective judgement learning during interactive activities. Effective strategies are required to moderate the conformity behaviour tendency (CBT) and improve reflective judgement performance (RJP). This study demonstrates two significant results: (a) Compared with the guided self-reflection learning strategy, the online collective reflection (OCR) learning strategy effectively weakened the learners' general CBT while dealing with professional controversial issues; and (b) a significantly negative correlation between the RJP achieved and the change of CBT in online environment was detected in the OCR group. The implications and potential applications in higher education were discussed. Further studies are needed to confirm the long-term effects and the extending application to other professional studies.