Computer-aided design and analysis of direct-driven wheel motordrive

This paper presents the computer-aided design (CAD) and performance analysis of a novel direct-driven wheel brushless DC motor drive for electric vehicles (EVs). The proposed motor is a permanent magnet square-wave motor, whose rotor with rare earth magnets forms the exterior of the motor, which can be fitted with a wheel tire to realize the direct drive for each wheel of an EV. The interior stator with its windings is rigidly mounted onto the suspension and frame structure of the vehicle. In order to achieve the direct drive without any mechanical transmission for EVs, the wheel motor has been designed as a low-speed high-torque motor. The design and optimization of the motor geometry was achieved with the aid of finite-element electromagnetic field analysis. Simulation studies on the transient performance of the motor drive were also carried out. This involved the creation of the motor transient model and formulation of a motor control strategy to ensure the wheel motor drive runs efficiently in the entire permitted speed and load range. The application of CAD techniques in the design of this very unconventional drive is described in this paper     

Increased analytical precision in the hollow cathode discharge emission source by improved discharge current control.

A significant improvement in the precision of the hollow cathode as an emission source is reported. Precision of 1% or less has been observed several times over periods of several hours. An average long-term stability of 4.3% for Ll and 6.0% for Na in the emission signal from microsamples (less than 50 nL) deposited in the hollow cathode discharge source is reported. The improved precision is attributed primarily to the introduction of electronics that hold the discharge current more nearly constant and to the shielding of all wiring to the source from the power supply. A current-controlled switch that is capable of driving a hollow cathode discharge in either dc or pulsed mode is described. This switch is capable of generating current pulses as short as 2 microseconds through a resistive load and greatly improves the discharge stability and repeatability at turn-on in both the dc and pulsed modes. The characteristics of pulses produced by this switch are presented; however, analytical performance is reported only for the dc mode. Temporal current plots are presented for the new instrumentation and compared to plots taken with commonly used current-controlled power supplies. Instrumentation, operation, and sample preparation procedures are described. Typical temporal profiles of the emission signal from microsamples deposited in AI and stainless steel hollow cathodes are given.     

Dbp5p, a cytosolic RNA helicase, is required for poly(A)+ RNA export

The DBP5 gene encodes a putative RNA helicase of unknown function in the yeast Saccharomyces cerevisiae. It is shown here that Dbp5p is an ATP-dependent RNA helicase required for polyadenylated [poly(A)+] RNA export. Surprisingly, Dbp5p is present predominantly, if not exclusively, in the cytoplasm, and is highly enriched around the nuclear envelope. This observation raises the possibility that Dbp5p may play a role in unloading or remodeling messenger RNA particles (mRNPs) upon arrival in the cytoplasm and in coupling mRNP export and translation. The functions of Dbp5p are likely to be conserved, since its potential homologues can be found in a variety of eukaryotic cells.     

Thermodynamic properties of iron doped beta″-alumina by e.m.f. measurements with beta-alumina electrolytes

Thermodynamic studies of the non-stoichiometric iron doped beta-alumina (ID) phase were carried out by electrochemical measurements coupled with coulometric titration using the cell Na_liq/Li-alumina/ID. Hot pressing and glass sealing techniques were developed and employed to obtain a suitable and stable Li-alumina/ID interface. The equilibrium e.m.f. of the cell was determined as a function of sodium concentration over the temperature range 444 to 523 K. The range of sodium concentrations over which the ID phase is stable was also determined. The relative partial molar thermodynamic quantities of sodium, , , and in ID alumina as a function of sodium concentration were obtained from cell e.m.f. data.     

Plasma graft polymerization of acrylamide onto crosslinked HTPB based PU membrane for pervaporation

Pervaporation of water-ethanol mixtures through plasma graft polymerization of acrylamide onto crosslinked hydroxyl terminated poly-butadiene (HTPB) based PU membranes, plasma graft polymerization of acrylamide onto crosslinked PU membrane (AAm-p-CPU), were investigated. The grafting was dependent on the discharge power and pretreatment period. The effects of crosslinking, plasma treatment conditions, feed compositions, and feed temperature on the performance of these membranes were studied. The physical properties of crosslinked membrane were better than those of the uncrosslinked membrane. In addition, compared with crosslinked PU membranes (CPU), the plasma modified crosslinked PU membranes effectively improve the pervaporation separation performances.     

Catalytic removal of SO2, NO and HCl from incineration flue gas over activated carbon-supported metal oxides

Activated carbon-supported copper, iron, or vanadium oxide catalysts were exposed to incineration flue gas to investigate the simultaneous catalytic oxidation of sulfur dioxide/hydrogen chloride and selective catalytic reduction of nitrogen oxide by carbon monoxide. The results show that AC-supported catalysts exhibit higher activities for SO₂ and HCl oxidation than traditional γ-Al₂O₃-supported catalysts and the iron and vanadium catalysts act as catalysts instead of sorbents, and can decompose sulfate with evolution of SO₃ and then regenerate for more SO₂ adsorption to take place. The AC-supported catalysts also display a high activity for NO reduction with CO generated from a flue gas incineration process and the presence of SO₂ in the incineration flue gas can significantly promote catalytic activity. Using CO as the reducing agent for NO reduction is more effective than using NH₃, because NH₃ may be partially oxidized in the presence of excess O₂ (12 vol%. in the incineration flue gas used) to form N₂, which can decrease the overall extent of NO reduction.     

Ultrasonic Spray Pyrolysis for Synthesis of Spherical Zirconia Particles

This paper presents new findings on ultrasonic spray pyrolysis of zirconium hydroxyl acetate precursor drops whose sizes were precisely measured using laser light diffraction technique. Precursor concentration plays a predominant role in determination of product particle size. At 0.01 wt% precursor concentration, conventional spray pyrolysis at 750°C using precursor drops 5–8 μm in diameter, generated by an ultrasonic nebulizer at 2.66 MHz, yielded uniform spherical yttria-stabilized zirconia (YSZ) particles 73 nm in diameter measured by scanning electron microscopy. The YSZ particle diameters were much smaller than those predicted by the one-particle-per-drop mechanism. Under similar reaction conditions, the high-throughput ultrasound-modulated two-fluid (UMTF) spray pyrolysis of larger precursor drops (28-μm peak diameter) also yielded spherical dense particles; they were significantly smaller in size than those produced by the low-throughput conventional ultrasonic spray pyrolysis of smaller drops (6.8-μm peak diameter).     

Growth of CeO2 Films on Sapphire and MgO by rf Magnetron Sputtering

pitaxial CeO₂ films on (1102) sapphire and (100) MgO were grown by rf magnetron sputtering. Substrate temperature, total pressure, and oxygen-to-argon mole ratio were varied to explore the optimal deposition condition. The X-ray diffraction spectra indicate that the degree of crystallinity of the deposited CeO₂ films depends on the oxygen- to-argon mole ratio and the substrate temperature. Atomic force microscopy images of the films on sapphire and MgO showed that substrate temperature and total pressure affect surface roughness. The best film surface is smooth with a 0.89 nm root-mean-square roughness. The quality of the films on MgO showed a strong dependence on substrate pretreatments. Epitaxial CeO₂ films could be grown on pre- annealed or pre-etched MgO if substrate temperatures reached higher than 790^deg;C. Additionally, the effect of ion bombardment at low total pressures on the crystallinity of the films was examined by growing the films outside the plasma region. Experimental results indicate that the ion bombardment does not prevent the films from preferred orientation.