Determination of dissolved natural thorium and uranium in Horonobe and Mizunami Underground Research Laboratory groundwater and its thermodynamic analysis

At two underground research laboratories situated at Horonobe and Mizunami, Japan, trace amounts of natural thorium and uranium dissolved in deep groundwater were investigated with the help of chemical pre-concentration method. The groundwater was sampled from underground boreholes under the geochemical condition of no atmospheric exposure, and the colloid contribution was checked by in situ two size-fractionated ultrafiltration systems. A rough decrease by half in the concentration after in situ filtration suggested the presence of natural colloids and suspended matter that were carriers of a portion of the elements. The Th and U concentrations in groundwater after 10 kDa filtration was evaluated as dissolved species, and was identified thermodynamically using existing hydrogeological and geochemical data, such as the mineral components in the groundwater at a given pH, ionic strength, concentration of co-existing ions, redox potential, and a hypothetical solubility-limiting solid phase. The crystalline solid phase of tetravalent thorium and uranium dioxides made the solubility very low compared with that of the amorphous phase.     

A study on the characteristics of glass fibre reinforced thermoplastics by transfer moulding

Lately, the use of fibre reinforced thermoplastics (FRTP) has increased due to its increased mouldability compared to thermosetting FRP material.

FRTP includes stampable sheet, short and long fibre reinforced thermoplastic pellets, continuous fibre reinforced thermoplastics sheets, etc. The long fibre reinforced thermoplastic (LFRTP) pellet has better mechanical properties than short fibre reinforced pellets and better mouldability than stampable sheet. At present, injection moulding method is mainly used for moulding LFRTP pellets because of its high productivity.

However, the long fibre of LFRTP pellets, whose length is the same as pellet length, is degraded during processing if conventional injection moulding machines are used, and as a result, the mechanical properties are not improved as expected in many cases. Therefore, a new moulding process is required to make good use of LFRTP pellets.

For this study, a transfer moulding apparatus was designed and built to minimize fibre degradation of the moulded parts.

Firstly, the LFRTP pellets with fibre lengths of 3, 6, 9, 12.7 and 17 mm were prepared in order to clarify the difference of mechanical properties due to fibre length. The fibre ratio was 30% in weight for all cases and the same polypropylene was used. They were moulded to the shape of the test specimens. Tensile, bending and Izod impact strengths were measured by using these test specimens. Secondly, LFRTP pellets were moulded to the shape of test specimens by the transfer moulding apparatus and conventional injection moulding machine, and then mechanical properties were measured. At the same time, short fibre pellets were moulded to the smae shape of test specimens by the injection moulding machine, and mechanical properties were compared with those of LFRTP pellets.

With the long glass fibre reinforced polypropylene, good results of fibre preservation and mechanical properties were obtained by the transfer moulding apparatus which was built for this study. The impact strength was increased remarkably as the fibre length increased, and consequently the preservation of fibre length in the moulded parts was especially effective in improving the impact strength.     

The characteristics of the external‐electrode mercury fluorescent lamp for backlighting liquid‐crystal‐television displays

Abstract— A reliable external‐electrode mercury fluorescent lamp (EEFL) has been developed for backlighting a liquid‐crystal‐television (LC‐TV) display. This involved the investigation of the EEFL characteristics and the improvement in the construction of the EEFL and drive waveforms, in the frequency range of 50–200 kHz, that affects the EEFL characteristics. The results showed that a sinusoidal waveform is suitable for driving the EEFL, and EEFL's voltage decreases when the frequency of the drive waveform is increased.     

Application of non-linear k–ω model to a turbulent flow inside a sharp U-bend

Simulation of the complex flow inside a sharp U-bend needs both refined turbulence models and higher order numerical discretization schemes. In the present study, a non-linear low-Reynolds number (low-Re) k–ω model including the cubic terms was employed to predict the turbulent flow through a square cross-sectioned U-bend with a sharp curvature, R _C/D = 0.65. In the turbulence model employed for the present study, the cubic terms are incorporated to represent the effect of extra strain-rates such as streamline curvature and three-dimensionality on both turbulence normal and shear stresses. In order to accurately predict such complex flowfields, a higher-order bounded interpolation scheme (Song et al., 1999) has been used to discretize all the transport equations. The calculated results by using both the non-linear k–ω model and the linear low-Reynolds number k–ɛ model (Launder and Sharma, 1974) have been compared with experimental data. It is shown that the present model produces satisfactory predictions of the flow development inside the sharp U-bend and well captures the characteristics of the turbulence anisotropy within the duct core region and wall sub-layer.     

A 0.18-μm 256-Mb DDR-SDRAM with low-cost post-mold tuning methodfor DLL replica

A 200-MHz double-data-rate synchronous-DRAM (DDR-SDRAM) was developed. The chip contains a delay-locked loop (DLL) which performs over a wide range of operating conditions. Post-mold-tuning allows precise replica programming. A 200-MHz intra-chip data bus is suitable for DDR operation     

Temperature measurements of polymer melts in the heating barrel during injection molding. Part 2: Three-dimensional temperature distribution in the reservoir

A new method has been developed to measure the three-dimensional temperature distribution of polymer melts in the reservoir of the heating barrel in the dynamic state. The procedure involves the use of a small-sheathed thermocouple in the nozzle of the machine. The tip of the thermocouple can be varied in depth from the surface to the center of the nozzle. The polymer melt of a shot is found to have a three-dimensional temperature distribution dependent on the geometry of the screw and the order of shot. These results reflect clearly the thermal histories of the polymer melt in the channel of the screw during plastication and conveyance, and indicate part of the dynamics of injection molding. Further, these measurements contribute to optimization of the design for the screw and the process conditions.     

Improvement of the Nelder-Mead method using Direct Inversion in Iterative Subspace

Optimization and Engineering - The Nelder-Mead (NM) method is a popular derivative-free optimization algorithm owing to its fast convergence and robustness. However, it is known that the method...     

Consideration of Femtosecond Radiation Generation on NewSUBARU Storage Ring

We studied on realization of short pulse gamma ray and X-ray simultaneously induced by a femtosecond laser on NewSUBARU storage ring. Based on the fact that the transverse dimensions of electron beam are much shorter than the longitudinal one, the laser light is arranged to collide the electron beam at a right angle to generate femtosecond pulse gamma ray, furthermore, the modulated part of the electron bunch gives rise to short pulse X-ray by synchrotron radiation from a downstream bending magnet. The temporal characteristic of the radiation is analyzed in this paper, as well as the performances are estimated.