Enhanced output power of near-ultraviolet InGaN-GaN LEDs grown on patterned sapphire substrates

Near-ultraviolet nitride-based light-emitting diodes (LEDs) with peak emission wavelengths around 410 nm were fabricated onto c-face patterned sapphire substrates (PSS). It was found that the electroluminescence intensity of the PSS LED shown 63% larger than that of the conventional LED. For a typical lamp-form PSS LED operating at a forward current of 20 mA, the output power and external quantum efficiency were estimated to be 10.4 mW and 14.1%, respectively. The improvement in the light intensity could be attributed to the decrease of threading dislocations and the increase of light extraction efficiency in the horizontal direction using a PSS.     

Chalcogenide Glasses Based on Germanium Disulfide for Second Harmonic Generation

High second‐order susceptibilities are created by thermal poling in bulk germanium disulfide based chalcogenide glasses. Experimental conditions of the poling treatment (temperature, voltage, time) were optimized for each glass composition. The second‐order nonlinear signals were recorded by using the Maker fringes experiment and a second‐order coefficient χ⁽²⁾ up to 8 pm V^–1 was measured in the Ge₂₅Sb₁₀S₆₅ glass. This value is obtained using a simulation based on accurate knowledge of the thickness of the nonlinear layer. Two mechanisms are proposed to explain the creation of a nonlinear layer under the anode: the formation and the migration of charged defects towards the anode may mainly occur in Ge₂₀Ga₅Sb₁₀S₆₅ and Ge₂₅Ga₅S₇₀ glasses, whereas the migration of Na⁺ ions towards the cathode may be responsible for the accumulation of negative charges under the anode in Ge₃₃S₆₇ and Ge₂₅Sb₁₀S₆₅ glasses. Different electronic conductivity behaviors seem to be at the origin of the phenomenon. In parallel, the potential effect of the poling treatment on the structural and electronic properties is studied using Raman spectroscopy and secondary ion mass spectroscopy measurements.     

用甲基异丁基酮萃取分离锆铪的工艺评价

简要评述了用甲基异丁基酮(MIBK)萃取分离锆铪方法的基本原理、分离工艺和条件、萃取设备.指出,MIBK在硫氰酸体系中萃取分离锆铪分离效果好,技术成熟,可进行规模生产.MIBK法的主要缺点是必须用有毒的SCN-作稀释剂,工艺复杂而冗长,操作不易控制,劳动强度大,收率低.MIBK在水中有较大的溶解度,废液不易处理,给工艺操作和环境带来极大困难.     

CB-60/CB-70还原态重整催化剂的应用

介绍了福建炼油化工有限公司重整装置CB -60 /CB -70重整催化剂 (还原态 )分段组合装填的应用情况 ,列出了还原态催化剂和氧化态催化剂开工的不同特点。通过开工初期标定的数据与CB -6/CB -7催化剂的对比 ,说明CB -60 /CB -70催化剂有良好的活性和选择性 ,尤其是选择性、产氢率优于CB -6/CB -7,且使开工步骤得到了简化     

ԥ�������С��¶���ͳ��������

豫西地区中、下二叠统太原组、山西组、上石盒子组及下石盒子组煤成气资源丰富，但成煤环境纵向发育与横向变化较大，规律难于把握。因此，开展煤成气源岩沉积环境研究有利于该区煤成气资源的勘探与开发及合理的利用。通过露头、钻井、地震资料及分析、测试资料的综合研究认为：本区中、下二叠统主要沉积了一套浅海碳酸盐岩，海湾-泻湖、潮坪、沼泽、障壁岛(砂质滩、坝)及三角洲相陆源碎屑岩和煤层。从总的沉积特征来看，下二叠统太原组、山西组基本上发育滨、浅海相碳酸盐岩、陆源碎屑岩和煤的混合沉积。上二叠统上、下石盒子组则以海陆交互相陆源碎屑沉积为主，三角洲及三角洲平原沼泽十分发育；沉积环境具有自下而上，自南东向北西方向由海相逐步过渡为陆相的基本特点。其煤成气源岩沉积环境以早二叠世山西期潮坪、泻湖过渡带之滨岸沼泽环境为最佳，其次为中二叠世下石盒子期三角洲平原沉积之平原沼泽环境。     

Piezoelectric Nanogenerators for Self-Powered Nanodevices

A novel approach converts nanoscale mechanical energy into electric energy for self-powering nanodevices.In our own work, we've used piezoelectric zinc-oxide nanowire (ZnO NW) arrays to demonstrate a novel approach for converting nanoscale mechanical energy into electric energy. Here, we review the fundamental principle behind the nanogenerator, present an approach for improving its performance, and discuss some of the challenges we face in pushing this technology to reach its potential.     

柳钢混铁炉炉衬结构及运行管理的技改实践

针对混铁炉使用过程中出现的各种侵蚀状况，设计采用砖砌十浇注复合炉衬结构，特别对前墙拐角和后墙中段等侵蚀快的关键部位作了有针对性的技术改进；在运行管理上，制定推行全新的工艺操作规程，取得了显著的使用效果。