Cu—Zn—Al合金逆形状记忆组织的电镜观察

用透射电镜观察了Cu-Zn-Al合金中逆形状记忆的贝氏体组织。在外加约束应力作用下,逆记忆量可以提高一个数量级,贝氏体片侧相界面的抛物线轮廓和贝氏体片交叉曲折的现象说明了贝氏体展宽是扩散控制的切变过程。     

40Cr钢渗氮过程中碳原子的迁移

将正火４０Ｃｒ钢样在不同温度下进行不同时间的气体渗氮，对其横断面进行波谱分析，发现渗氮前沿附近自始至终存在着典型的贫碳区，其两侧为富碳区，透射电镜分析结果表明，碳原子的重新分布包括碳化物的回溶、碳的扩散及碳化物长大三个过程。     

Study of modeling and simulation of full digital controlled PMIG／MAG welding system based on Matlab／Simulink

This paper presents an integrated simulation model for full digital controlled PMIG/MAG welding system with Matlab/Simulink, and it consists of power inverter, digital control system and dynamic arc-load model. An integrated simulation study was done for fuU digital PMIG/MAG welding, and a method of connecting dynamic arc-load model to the system with controlled current source was presented, in addition, the simulation results were utilized to study the issues of digital control PMIG/MAG welding in this paper. The experimental results validated the developed simulation model, and this simulation study can be applied in implementation of the full digital PMIG/MAG welding and analysis of system dynamic process.     

Effect of Mn and MnS on corrosion properties of domestic pipeline steels and welds

Base metals of domestic pipeline steels were used to study the effect of Mn on corrosion properties of SSCC( Sulfide Stress Corrosion Cracking), and welds were carried out to study the effect of MnS on corrosion properties of HIC ( Hydrogen Induced Cracking) both in solutions with wet hydrogen sulfide ( H2 S ). They were respectively conducted by referring to the standards of SSCC and HIC. Testing results revealed that with the increase of content Mn, the resistance of SSCC will be decreased, from the point of metallurgic view, and it is Mn element not C element to lead to the testing results of SSCC. Meanwhile, even under the condition without inclusions MnS, HIC in welds still occurred. That is to say, MnS is not necessary for HIC, the presence of local banded structures in which Mn and P are inclined to aggregate cause to the phenomena of HIC.     

多程序点焊控制器的研制

本文主要介绍了多程序点焊控制箱的程序过程以及主控制器及调制器的工作原理，并采用了一种新型的触发电路代替传统的脉冲变压器，具有触发可靠、大功率、高精度、电路简单等特点。     

INFLUENCE OF RESIDUAL STRESS AND SURFACE MORPHOLOGY ON FATIGUE PROPERTIES OF STEEL 60Mn

Influence of residual stress and surface morphology induced by shot-peening on fatigue behav-ior of a medium temperature tempered spring steel 60 Mn has been studied.The compressiveresidual stress induced in the near-surface region may improve fatigue limit from 930 to 1010MPa,and the very high tensile residual stress in the interior may reduce it from 1010 to 940MPa,whereas the severe surface damage may cause a drop-off of it from 1010 down to 800MPa.Fatigue cracks initiated in such position where the equivalent Mises stress,includingresidual stress,exceeded the local strength of the material.The compressive residual stress,induced by shot-peening,may intensify the effect of crack closure,so as to decrease the crackgrowth rate.     

SOME THERMODYNAMIC PROPERTIES IN PROCESS OF THERMAL REDUCTION OF Mg WITH HIGH AI ALLOY

本文以含高Al(Al76％,Si18.9％,Fe5.1％)的Al-Si-Fe合金为还原剂,在不同温度下进行热法还原Mg实验,测定了Mg的蒸气压为lgp_(Mg)=-8853/T+10.58.与用Si-Fe还原剂相比,在相同的p_(Mg)下,还原温度可下降约200℃。 用Bonnier法和本实验所测定的数据计算了Al-Si-Fe合金在不同温度下各组元的活度。结果表明,三元系中各组元活度均有负偏差,尤其Fe的偏差很大。另外,由以上所得的活度数据还计算了还原反应的平衡常数和热焓,分别为: lgK_[Al]=-18.40×10~4/T+117.2,ΔH=3529.5KJ     

PORTEVIN-LE CHATELIER EFFECT IN COMMERCIAL AI-Cu-Mg ALLOY

在一定的温度和应变速率范围内研究了淬火和淬火后经短期人工时效处理的Al-Cu-Mg合金薄板的Portevin-Le Chatelier效应.结果表明,淬火后短期人工时效处理可以推迟产生波纹痕迹.据此,提出了推迟板材产生不均匀变形带的措施.     

SOME EXPERIMENTS ON THE PURIFICATION OF ALUMINUM AND TIN BY THE ZONE-MELTING METHOD

<正> 用作半导体材料的锗和硅,需要高度纯化方能使用,已为众所周知。在研究金属的许多物理性质方面,如结晶凝固的过程,金属的强度、腐蚀及内部原子的扩散,合金的相图等,也常常需要先有纯金属或“纯合金”,方能进一步控制其他条件,系统地研究它们之间相应的规律。