Thermal simulation for geometric optimization of metallizedpolypropylene film capacitors

In this paper, the authors use an analytical model to calculate the losses in the metallized polypropylene film capacitors. The model is validated experimentally for capacitors having the same capacitance but different geometry. For each group of capacitors, a temperature distribution in the roll is assumed with the aim of optimizing its thermal performance. It appears that the heating of a long capacitor is higher than that of an equivalent flat capacitor subjected to the same electric stresses     

A New Algorithm for the Elimination of Common Subexpressions in Hardware Implementation of Digital Filters by Using Genetic Programming

A new algorithm based on Genetic Programming (GP) for the problem of optimization of Multiple constant Multiplication (MCM) by Common Subexpression Elimination(CSE) is developed. This method is used for hardware optimization for DSP systems. A solution based on Genetic Programming is shown in this paper. The performance of the technique is demonstrated in one- and multi-dimensional digital filters with constant coefficients.     

Impact of temperature cycle profile on fatigue life of solder joints

In this paper the influence of the temperature cycle time history profile on the fatigue life of ball grid array (BGA) solder joints is studied. Temperature time history in a Pentium processor laptop computer was measured for a three-month period by means of thermocouples placed inside the computer. In addition, Pentium BGA packages were subjected to industry standard temperature cycles and also to in-situ measured temperature cycle profiles. Inelastic strain accumulation in each solder joint during thermal cycling was measured by high sensitivity Moire interferometry technique. Results indicate that fatigue life of the solder joint is not independent of the temperature cycle profile used. Industry standard temperature cycle profile leads to conservative fatigue life observations by underestimating the actual number of cycles to failure.     

Preliminary<Emphasis Type="Italic">in vitro</Emphasis> and<Emphasis Type="Italic">in vivo</Emphasis> characterizations of a sol-gel derived bioactive glass-ceramic system

This study investigates quantitatively and qualitatively the sol-gel derived bioactive glass-ceramic system (BGS)—apatite-wollastonite (AW) type granules in the size range of 0.5–1 mm, as an effective graft material for bone augmentation and restoration. Scanning electron micrographs (SEM) of the sintered granules revealed the rough material surface with micropores in the range 10–30 μm. X-ray diffraction (XRD) pattern of the granules revealed the presence of crystalline phases of the hydroxyapatite and wollastonite, and the functional groups of the silicate and phosphates were identified by Fourier transform infrared spectroscopy (FT-IR). Thein vitro cell culture studies with L929 mouse fibroblast cell line showed very few cells adhered on the BGS disc after 24 h. This could be due to the highly reactive surface of the disc concomitant with the crystallization but not due to the cytotoxicity of the material, since the cellular viability (MTT assay) with the material was 80‰ Cytotoxicity and cytocompatibility studies proved that the material was non-toxic and biocompatible. After 12 weeks of implantation of the BGS granules in the tibia bone of New Zealand white rabbits, the granules were found to be well osteointegrated, as observed in the radiographs. Angiogram with barium sulphate and Indian ink after 12 weeks showed the presence of microcapillaries in the vicinity of the implant site implicating high vascularity. Gross observation of the implant site did not show any inflammation or necrosis. SEM of the implanted site after 24 weeks revealed good osteointegration of the material with the newly formed bone and host bone. New bone was also observed within the material, which was degrading. Histological evaluation of the bone healing with the BGS granules in the tibial defect at all time intervals was without inflammation or fibrous tissue encapsulation. After 2 weeks the new bone was observed as a trabeculae network around the granules, and by 6 weeks the defect was completely closed with immature woven bone. By 12 weeks mature woven bone was observed, and new immature woven bone was seen within the cracks of the granules. After 24 weeks the defect was completely healed with lamellar bone and the size of the granules decreased. Histomorphometrically the area percentage of new bone formed was 67.77% after 12 weeks and 63.37% after 24 weeks. Less bone formation after 24 weeks was due to an increased implant surface area contributed by the material degradation and active bone remodeling. The osteostimulative and osteoconductive potential of the BGS granules was established by tetracycline labelling of the mineralizing areas by 2 and 6 weeks. This sol-gel derived BGS granules proved to be bioactive and resorbable which in turn encouraged active bone formation.     

Mechanical and microstructure studies on the modification of CA film by blending with PS

DriedMusa paradiciaca (banana) stem and veins of the leaves, which were hitherto discarded as a waste, were collected and used as starting material for the preparation of cellulose and cellulose acetate. This cellulose acetate was mixed with polystyrene to form blend of cellulose acetate-polystyrene in order to provide enhanced stability and extended utility to the end products. The films of these composites or their individual partners were made separately and studied for their mechanical properties, chemical modification and morphological changes. We report here that banana stem is good source of cellulose and that cellulose completely undergoes modification upon esterification.     

A study on hydrogen storage by use of cryoadsorbents

This paper reports investigations on the techniques and economics of hydrogen storage by means of cryoadsorption. Also a comparison with alternative storage methods is included. The hydrogen storage capacity of several adsorbents in the temperature range 65–150 K has been investigated experimentally. Based on these data, economics and operating conditions for minimum total costs of the system are calculated. Utilization-factor and capacity-factor parameters are shown to be decisive for outlining the favourable ranges of application for competitive hydrogen storage methods.     

Finite element hourglassing control

A new hourglassing control technique for quadrilateral and hexahedral elements used in dynamic finite element codes is presented. Based on expansion of the strees in a Taylor series and retention of additional terms beyond the usual constant stress term, this technique has the advantage that actual rather than artificial material properties are used. Simplifications that render this technique competitive with artificial viscosity and stiffness procedures in terms of additional storage and computation requirements are described.     

Novel bipolar differential input/output current-controlled current source

A new bipolar differential input/output current-controlled current source (CCCS) is described. The basic cell consists of a translinear array of six transistors with two bipolar inputs, and is suited for the input stage of a differential current-mode operational amplifier.