Evaluation and unification of some methods for estimating reflectance spectra from RGB images

The problem of estimating spectral reflectances from the responses of a digital camera has received considerable attention recently. This problem can be cast as a regularized regression problem or as a statistical inversion problem. We discuss some previously suggested estimation methods based on critically undersampled RGB measurements and describe some relations between them. We concentrate mainly on those models that are using a priori information in the form of high-resolution measurements. We use the "kernel machine" framework in our evaluations and concentrate on the use of multiple illuminations and on the investigation of the performance of global and locally adapted estimation methods. We also introduce a nonlinear transformation of reflectance values to ensure that the estimated reflection spectra fulfill physically motivated boundary conditions. The reported experimental results are derived from measured and simulated camera responses from the Munsell Matte, NCS, and Pantone data sets.     

Microchip sonic spray ionization

The first microchip version of sonic spray ionization (SSI) as an atmospheric pressure ionization source for mass spectrometry (MS) is presented. The microchip used for SSI has recently been developed in our laboratory, and it has been used before as an atmospheric pressure chemical ionization (APCI) and atmospheric pressure photoionization (APPI) source. Now the ionization is achieved simply by applying high (sonic) speed nebulizer gas, without heat, corona discharge, or high voltage. The microchip SSI was applied to the analysis of tetra-N-butylammonium, verapamil, testosterone, angiotensin I, and ibuprofen. The limits of detection were in the range of 15 nM to 4 microM. The technique was found to be highly dependent on the position of the chip toward the mass spectrometer inlet, and on the gas and the sample solution flow rates. The microchip SSI provided dynamic linearity following a pattern similar to that used with electrospray, good quantitative repeatability (RSD=16%), and long-term signal stability.     

Microchip for combining gas chromatography or capillary liquid chromatography with atmospheric pressure photoionization-mass spectrometry

We present a microfabricated nebulizer chip for combining atmospheric pressure photoionization-mass spectrometry (APPI-MS) with gas chromatography (GC) or capillary liquid chromatography (capLC). The chip consists of a silicon plate and a glass plate or two glass plates. The chip includes a sample inlet channel, auxiliary gas and dopant inlet, vaporizer channel, nozzle, and platinum heater. The sample eluted from the capLC or GC is mixed with auxiliary gas and dopant (toluene) in the heated vaporizer. The chip forms a confined jet of the sample vapor, which is photoionized as it exits the chip. The analytical performance of GC- and capLC-microchip APPI-MS was evaluated with some polycyclic aromatic hydrocarbons, amphetamines, and steroids. The GC-muAPPI-MS method provides high sensitivity down to 0.8 fmol, repeatability (RSD = 7.5-14%), and linearity (r = 0.9952-0.9987). The capLC-muAPPI-MS method shows high sensitivity down to 1 fmol, good repeatability (RSD = 3.6-8.1%), and linearity (r = 0.9989-0.9992).     

Post-growth annealing of type-II GaSb/GaAs quantum dots grown with different V/III ratios

We report the influence of V/III beam-equivalent-pressure ratios and post-growth annealing on the photoluminescence of GaSb quantum dots grown on GaAs(1 0 0) by molecular beam epitaxy. Increasing the V/III beam-equivalent-pressure ratio from 3 to 5 and then to 7 results in decreased photoluminescence intensity and redshifts the photoluminescence wavelength. The post-growth annealing blueshifts the quantum dot photoluminescence emission and decreases the full-width-at-half-maximum of the photoluminescence peak when annealing temperature is increased above 800 °C. The blueshift behavior is found to be independent on the V/III ratios indicating a similar atomic interdiffusion mechanism for all investigated samples regardless of the quantum dot properties. The photoluminescence intensities of the three samples experience an increase after moderate annealing. Whereas the intensity of the sample with the highest V/III ratio further increases, the intensity of the sample with lower V/III ratios decreases again upon higher annealing steps above 900 °C. Furthermore, temperature- and power dependent photoluminescence measurements are performed on as-grown and 870 °C annealed samples with V/III ratios of 3 and 7 in order to study the reduced quantum dot confinement in more detail.     

Design of non-paraxial array illuminators by step-transition perturbation approach

Abstract

We introduce an efficient Fourier-domain formulation of an approximate method to model non-paraxial diffractive elements. The method is based on evaluation of local field perturbations caused by abrupt surface-profile transitions. It facilitates fast parametric optimization of binary and four-level diffractive array illuminators in the non-paraxial domain of diffractive optics. Comparison with rigorous electromagnetic theory of gratings shows that optimization with the perturbation method gives accurate results if the smallest feature size in the surface profile is larger than one wavelength. Some binary designs are demonstrated using electron beam lithography.     

Desorption and ionization mechanisms in desorption atmospheric pressure photoionization

The factors influencing desorption and ionization in newly developed desorption atmospheric pressure photoionization-mass spectrometry (DAPPI-MS) were studied. Redirecting the DAPPI spray was observed to further improve the versatility of the technique: for dilute samples, parallel spray with increased analyte signal was found to be the best suited, while for more concentrated samples, the orthogonal spray with less risk for contamination is recommended. The suitability of various spray solvents and sampling surface materials was tested for a variety of analytes with different polarities and molecular weights. As in atmospheric pressure photoionization, the analytes formed [M + H](+), [M - H](-), M(+*), M(-*), [M - H + O](-), or [M - 2H + 2O](-) ions depending on the analyte, spray solvent, and ionization mode. In positive ion mode, anisole and toluene as spray solvents promoted the formation of M(+*) ions and were therefore best suited for the analysis of nonpolar compounds (anthracene, benzo[a]pyrene, and tetracyclone). Acetone and hexane were optimal spray solvents for polar compounds (MDMA, testosterone, and verapamil) since they produced intensive [M + H](+) ion peaks of the analytes. In negative ion mode, the type of spray solvent affected the signal intensity, but not the ion composition. M(-*) ions were formed from 1,4-dinitrobenzene, and [M - H + O](-) and [M - 2H + 2O](-) ions from 1,4-naphthoquinone, whereas acidic compounds (naphthoic acid and paracetamol) formed [M - H](-) ions. The tested sampling surfaces included various materials with different thermal conductivities. The materials with low thermal conductivity, i.e., polymers like poly(methyl methacrylate) and poly(tetrafluoroethylene) (Teflon) were found to be the best, since they enable localized heating of the sampling surface, which was found to be essential for efficient analyte desorption. Nevertheless, the sampling surface material did not affect the ionization mechanisms.     

Structural and rheological investigation of interphase in polyethylene/polyamide/nanoclay ternary blends

This study aims at investigating and characterizing the interphase in Polyethylene (PE)/Polyamide (PA) blends with nodular morphology, filled with organically modified Montmorillonite (C30B), using structural and rheological experimental techniques. PE/PA/C30B blends have been prepared by simultaneous mixing at a dispersed phase fraction (PE or PA) of 20% and a clay fraction ranging from 1 to 6%. Structural properties of the interphase have been investigated using XRD combined with TEM micrographs. The presence of numerous interphase defects is evidenced, and the effect of interphase disorder is discussed. Linear viscoelastic properties show the contribution of the interphase in PE matrix ternary blends at all clay fractions, whereas interphase effects are masked by the contribution of dispersed nanoclay particles in PA matrix ternary blends.     

System- and circuit-level optimization of PLL designs for DVB-T/H receivers

This article proposes a framework for the optimization of voltage-controlled oscillator (VCO) designs in frequency synthesizers for digital video broadcasting ?C terrestrial/handheld (DVB-T/H) receivers. Linear time-invariant phase-domain model of a charge-pump phase-locked loop (PLL) is devised and includes both flicker (1/f) and thermal noise contributions from the loop oscillators. By modeling the entire receiver, it is shown that there are combinations of flicker and thermal noise contributions that result in a constant sum of inter-carrier interference (ICI) and adjacent channel interference, and constant symbol error rate as well. Consequently, optimization of the VCO phase noise spectrum is defined while maintaining the standard-specified symbol-error rate. Link-level performance evaluation is carried out to validate the stipulated trade-off. The effect of ICI mitigation schemes is discussed. Circuit-level VCO design approaches utilizing the derived trade-off are finally presented. The proposed optimization procedure is generic and is also applicable to other systems based on Orthogonal Frequency-Division Multiplexing.     

An Investigation on the Reduced Ability of IF-MoS2 Nanoparticles to Reduce Friction and Wear in the Presence of Dispersants

Inorganic fullerene-like molybdenum disulfide (IF-MoS₂) nanoparticles are known to exhibit great friction and wear-reducing abilities in severe boundary lubrication regimes, when added to a base oil alone. Their use in fully formulated lubricants was investigated in this study, and the tribological benefits attributed to the IF-MoS₂ nanoparticles were found to be lost in the presence of dispersants. Various experimental techniques were used on three reference oils (base oil containing only IF-MoS_2, only dispersants and both IF-MoS₂ and dispersants) in order to understand the effect of succinimide-based dispersants on the three phases needed for effective nanoparticle-based lubrication, namely (1) the passing of the nanoparticles through the contact (2) the exfoliation of the IF-MoS₂ inside the contact and (3) the adhesion of the released MoS₂ platelets on the friction surfaces. The dispersants were shown to improve the dispersion of the nanoparticles in the oil by reducing their agglomeration, but prevented the adhesion of a low-friction MoS₂ tribofilm on the steel surfaces. In-situ contact visualization revealed that the well-dispersed nanoparticles passed through the contact and exfoliated nanoparticles were observed after tribological testing. These results imply that nanoparticle dispersion itself does not seem to be an issue concerning nanoparticle effectiveness, even though the reduced agglomerate size and inertia may have affected nanoparticle flow near the contact, as well as entrapment and exfoliation conditions inside the contact. The use of succinimide-based dispersants may, however, have affected the tribochemistry of the contact, by an excessive adsorption on the steel surfaces and/or by encapsulating the released MoS₂ platelets, preventing tribofilm adhesion. A balance was finally found between nanoparticle dispersion and friction reduction, but for very low dispersant concentrations and after a running-in period. The role of succinimide-based dispersants and their effect on nanoparticle lubrication were discussed in the light of these results.