Programmable SiGe BiCMOS low-pass filter for a multicarrier WCDMA base-station receiver

SiGe BiCMOS low-pass filter for a multicarrier WCDMA base-station receiver is described in this paper. The 4th-order Chebyshev filter with a 0.1-dB passband ripple is designed to drive a high-resolution A/D converter. The −3-dB frequency of the implemented filter can be programmed to four different bandwidths: 2.5, 5, 7.5, and 10 MHz depending on the number of received WCDMA channels. The filter achieves +9.7-dBV in-band IIP3, +20-dBV out-of-band IIP3, and 8.5-nV/√Hz input-referred noise density with 10-MHz bandwidth. The circuit uses a 2.5 V supply and has been fabricated in a 0.25-μm SiGe BiCMOS process.     

Evaluation and unification of some methods for estimating reflectance spectra from RGB images

The problem of estimating spectral reflectances from the responses of a digital camera has received considerable attention recently. This problem can be cast as a regularized regression problem or as a statistical inversion problem. We discuss some previously suggested estimation methods based on critically undersampled RGB measurements and describe some relations between them. We concentrate mainly on those models that are using a priori information in the form of high-resolution measurements. We use the "kernel machine" framework in our evaluations and concentrate on the use of multiple illuminations and on the investigation of the performance of global and locally adapted estimation methods. We also introduce a nonlinear transformation of reflectance values to ensure that the estimated reflection spectra fulfill physically motivated boundary conditions. The reported experimental results are derived from measured and simulated camera responses from the Munsell Matte, NCS, and Pantone data sets.     

Microchip sonic spray ionization

The first microchip version of sonic spray ionization (SSI) as an atmospheric pressure ionization source for mass spectrometry (MS) is presented. The microchip used for SSI has recently been developed in our laboratory, and it has been used before as an atmospheric pressure chemical ionization (APCI) and atmospheric pressure photoionization (APPI) source. Now the ionization is achieved simply by applying high (sonic) speed nebulizer gas, without heat, corona discharge, or high voltage. The microchip SSI was applied to the analysis of tetra-N-butylammonium, verapamil, testosterone, angiotensin I, and ibuprofen. The limits of detection were in the range of 15 nM to 4 microM. The technique was found to be highly dependent on the position of the chip toward the mass spectrometer inlet, and on the gas and the sample solution flow rates. The microchip SSI provided dynamic linearity following a pattern similar to that used with electrospray, good quantitative repeatability (RSD=16%), and long-term signal stability.     

Microchip for combining gas chromatography or capillary liquid chromatography with atmospheric pressure photoionization-mass spectrometry

We present a microfabricated nebulizer chip for combining atmospheric pressure photoionization-mass spectrometry (APPI-MS) with gas chromatography (GC) or capillary liquid chromatography (capLC). The chip consists of a silicon plate and a glass plate or two glass plates. The chip includes a sample inlet channel, auxiliary gas and dopant inlet, vaporizer channel, nozzle, and platinum heater. The sample eluted from the capLC or GC is mixed with auxiliary gas and dopant (toluene) in the heated vaporizer. The chip forms a confined jet of the sample vapor, which is photoionized as it exits the chip. The analytical performance of GC- and capLC-microchip APPI-MS was evaluated with some polycyclic aromatic hydrocarbons, amphetamines, and steroids. The GC-muAPPI-MS method provides high sensitivity down to 0.8 fmol, repeatability (RSD = 7.5-14%), and linearity (r = 0.9952-0.9987). The capLC-muAPPI-MS method shows high sensitivity down to 1 fmol, good repeatability (RSD = 3.6-8.1%), and linearity (r = 0.9989-0.9992).     

High-level parameterizable area estimation modeling for ASIC designs

Architectural design space exploration and early area budgeting for ASIC and IP block development require accurate high level gate count estimation methods without requiring the hardware being fully specified. The proposed method uses hierarchical and parameterizable models requiring minimal amount of information about the implementation technology to meet this goal. The modeling process flow is to: (1) create a block diagram of the design, (2) create a model for each block, and (3) sum up estimates of all sub-blocks by supplying the correct parameters to each sub-model. We discuss the model creation for a few parameterized library blocks as well as three communication blocks and a processor core from real IC projects ranging from 22 to 250 kgates. The average relative estimation error of the proposed method for the library blocks is 3.2% and for the real world examples 4.0%. The best application of this method is early in the design phase when different implementation architectures are compared.     

An Experimental Study on the Concentration and Shape of Dents Caused by Spherical Metallic Particles in EHL Contacts©

An experimental study of metallic contaminant effects on surface indentation in EHL contacts is presented. Particles are initially spherical and are composed of M50 high-carbon steel powder. Their diameter ranges from 32 to 40 μm. An original lubrication system with a controlled level of contamination was built. The contaminant distribution and concentration are measured on-line by an automatic particle counter. Tests are conducted on a two-disk machine with different operating conditions. Particles may travel through the EHL contact only one time, the lubricant flow being used only once. The oil is a synthetic one qualified under the MIL-L-23699 specification. An optical profilometer is used to describe the indent topography and a CCD video camera to count the number of dents.

The test bench is described and the experimental procedure is presented. Specific tests were performed to quality the contamination bench. The combined effects of particles concentration and test duration on dent distribution were studied. Some results on the shape and concentration of indents versus operating conditions are presented. It is shown that over the range of test conditions considered, the number of indents on the raceways can be estimated from the particle concentration in the oil bulk. This leads to the conclusion that the particle entry ratio is close to one, i.e., the concentration of particles inside the EHL contact is close to those in the bulk.     

Post-growth annealing of type-II GaSb/GaAs quantum dots grown with different V/III ratios

We report the influence of V/III beam-equivalent-pressure ratios and post-growth annealing on the photoluminescence of GaSb quantum dots grown on GaAs(1 0 0) by molecular beam epitaxy. Increasing the V/III beam-equivalent-pressure ratio from 3 to 5 and then to 7 results in decreased photoluminescence intensity and redshifts the photoluminescence wavelength. The post-growth annealing blueshifts the quantum dot photoluminescence emission and decreases the full-width-at-half-maximum of the photoluminescence peak when annealing temperature is increased above 800 °C. The blueshift behavior is found to be independent on the V/III ratios indicating a similar atomic interdiffusion mechanism for all investigated samples regardless of the quantum dot properties. The photoluminescence intensities of the three samples experience an increase after moderate annealing. Whereas the intensity of the sample with the highest V/III ratio further increases, the intensity of the sample with lower V/III ratios decreases again upon higher annealing steps above 900 °C. Furthermore, temperature- and power dependent photoluminescence measurements are performed on as-grown and 870 °C annealed samples with V/III ratios of 3 and 7 in order to study the reduced quantum dot confinement in more detail.     

Design of non-paraxial array illuminators by step-transition perturbation approach

Abstract

We introduce an efficient Fourier-domain formulation of an approximate method to model non-paraxial diffractive elements. The method is based on evaluation of local field perturbations caused by abrupt surface-profile transitions. It facilitates fast parametric optimization of binary and four-level diffractive array illuminators in the non-paraxial domain of diffractive optics. Comparison with rigorous electromagnetic theory of gratings shows that optimization with the perturbation method gives accurate results if the smallest feature size in the surface profile is larger than one wavelength. Some binary designs are demonstrated using electron beam lithography.     

Desorption and ionization mechanisms in desorption atmospheric pressure photoionization

The factors influencing desorption and ionization in newly developed desorption atmospheric pressure photoionization-mass spectrometry (DAPPI-MS) were studied. Redirecting the DAPPI spray was observed to further improve the versatility of the technique: for dilute samples, parallel spray with increased analyte signal was found to be the best suited, while for more concentrated samples, the orthogonal spray with less risk for contamination is recommended. The suitability of various spray solvents and sampling surface materials was tested for a variety of analytes with different polarities and molecular weights. As in atmospheric pressure photoionization, the analytes formed [M + H](+), [M - H](-), M(+*), M(-*), [M - H + O](-), or [M - 2H + 2O](-) ions depending on the analyte, spray solvent, and ionization mode. In positive ion mode, anisole and toluene as spray solvents promoted the formation of M(+*) ions and were therefore best suited for the analysis of nonpolar compounds (anthracene, benzo[a]pyrene, and tetracyclone). Acetone and hexane were optimal spray solvents for polar compounds (MDMA, testosterone, and verapamil) since they produced intensive [M + H](+) ion peaks of the analytes. In negative ion mode, the type of spray solvent affected the signal intensity, but not the ion composition. M(-*) ions were formed from 1,4-dinitrobenzene, and [M - H + O](-) and [M - 2H + 2O](-) ions from 1,4-naphthoquinone, whereas acidic compounds (naphthoic acid and paracetamol) formed [M - H](-) ions. The tested sampling surfaces included various materials with different thermal conductivities. The materials with low thermal conductivity, i.e., polymers like poly(methyl methacrylate) and poly(tetrafluoroethylene) (Teflon) were found to be the best, since they enable localized heating of the sampling surface, which was found to be essential for efficient analyte desorption. Nevertheless, the sampling surface material did not affect the ionization mechanisms.     

System- and circuit-level optimization of PLL designs for DVB-T/H receivers

This article proposes a framework for the optimization of voltage-controlled oscillator (VCO) designs in frequency synthesizers for digital video broadcasting ?C terrestrial/handheld (DVB-T/H) receivers. Linear time-invariant phase-domain model of a charge-pump phase-locked loop (PLL) is devised and includes both flicker (1/f) and thermal noise contributions from the loop oscillators. By modeling the entire receiver, it is shown that there are combinations of flicker and thermal noise contributions that result in a constant sum of inter-carrier interference (ICI) and adjacent channel interference, and constant symbol error rate as well. Consequently, optimization of the VCO phase noise spectrum is defined while maintaining the standard-specified symbol-error rate. Link-level performance evaluation is carried out to validate the stipulated trade-off. The effect of ICI mitigation schemes is discussed. Circuit-level VCO design approaches utilizing the derived trade-off are finally presented. The proposed optimization procedure is generic and is also applicable to other systems based on Orthogonal Frequency-Division Multiplexing.