Guar gum methyl ethers. Part I. Synthesis and macromolecular characterization

Guar gum (GG) has been partially methyl-etherified under heterogeneous reaction conditions. The resulting products, (methyl ether guar: MG) with different degrees of substitution, have been characterized by means of viscosity, ¹H NMR, and FTIR measurements. The introduction of methoxyl groups along the polysaccharidic chains reduces the hydrogen bonding sites on the guar backbone reducing primarely the extent of hydrogen bonding between guar macromolecules, hence their aggregation tendency. A comparative analysis of Mark–Houwink–Sakurada parameters and of the characteristic ratio (C_∞) of GG and MG samples in aqueous solution has been carried out using the Burchard–Stockmayer–Fixman method for flexible and semiflexible chains. The MG chains exhibit more flexibility than those of native guar gum which is traceable to a disruption of intrachain hydrogen bonds.     

Increase of trans-resveratrol in typical Sicilian wine using β-Glucosidase from various sources

β-Glucosidase (EC 3.2.1.21) (β-G) from different sources were tested to increase the trans-resveratrol in some Sicilian wines by hydrolysing resveratrol glucoside. β-G from Aspergillus niger mould was tested as a crude and purified enzyme, and compared with the same enzyme from Saccharomyces cerevisiae yeast. Specific purification served to eliminate collateral enzyme activities so that β-G could be used simply and economically. Aspergillus niger β-G produced trans-resveratrol increases of up to 75%, with no change in physico-chemical properties and bouquet, and an increase in health and nutritional properties. S. cerevisiae β-G raised free-terpenol levels, but impaired wine colour due to anthocyanase activity.     

Analytical approach for thermal and electrical design of multilayerstructure integrated devices

An analytical method for the electrothermal design of multilayer structure integrated devices is presented. It can be easily applied to a large variety of devices and is independent of the specific physical properties of the layers, also accounting for the temperature dependence of the thermal conductivity     

Thermodynamic properties of amorphous silicon via tight binding simulations

An atomic-scale structure of amorphous silicon, generated by reverse Monte Carlo, has been used as a starting configuration for finite temperature molecular dynamics simulations performed by an orthogonal tight binding Hamiltonian. Structural, dynamic, elastic and electronic structure properties have been investigated in the range of temperatures up to and above the melting transition. The amorphous silicon structure undergoes a melting transition at a temperature sensibly smaller than that of the crystalline structure. Above this temperature, the structure has the same properties of an under-cooled liquid and it has a metallic behavior.     

Present status of the theory of electron beam instabilities in storage rings

The coherent beam instabilities in circular accelerators are explained in terms of simple concepts of feedback devices. The notion of coupling impedance is introduced and interpreted by means of engineering circuit analysis. The condition of stability for the coherent motion is given in terms of the coupling impedance and accelerator and beam parameters.     

Methodology for development of live load models for refined analysis of short and medium-span highway bridges

Abstract

The accuracy of bridge system safety evaluations and reliability assessments obtained through refined structural and finite element analyses depends not only on the accuracy of the structural model itself but also on the proper modelling of the maximum traffic loads. While current code-specified live load models were calibrated to properly reflect the safety levels of bridge structures analysed using the simplified methods adopted in bridge design and evaluation manuals, these load models may not lead to accurate results when implemented during refined structural analysis procedures. This paper describes a method to calibrate appropriate live load models that can be used for advanced analyses of bridges. The calibration procedure is demonstrated using actual traffic data collected at a representative weigh-in-motion station in New York State. The proposed calibration methodology is applicable for developing live load models for different bridge service periods, bridge types and design/assessment codes or standards. Live load models obtained using the proposed calibration procedure are readily implementable for deterministic refined analyses of highway bridges to produce similar results to those of complex traffic load simulations. Examples are presented that describe how results of such calibrated live load models would be used in engineering practice.     

Signalling chains with probe and adjust learning

Many models explain the evolution of signalling in repeated stage games on social networks, differently in this study each signalling game evolves a communication strategy to transmit information across the network. Specifically, I formalise signalling chain games as a generalisation of Lewis' signalling games, where a number of players are placed on a chain network and play a signalling game in which they have to propagate information across the network. I show that probe and adjust learning allows the system to develop communication conventions, but it may temporarily perturb the system out of conventions. Through simulations, I evaluate how long the system takes to evolve a signalling convention and the amount of time it stays in it. This discussion presents a mechanism in which simple players can evolve signalling across a social network without necessarily understanding the entire system.     

Italian multicentre study on microbial environmental contamination in dental clinics: a pilot study

The dental practice is associated with a high risk of infections, both for patients and healthcare operators, and the environment may play an important role in the transmission of infectious diseases. A microbiological environmental investigation was carried out in six dental clinics as a pilot study for a larger multicentre study that will be performed by the Italian SItI (Society of Hygiene, Preventive Medicine and Public Health) working group "Hygiene in Dentistry". Microbial contamination of water, air and surfaces was assessed in each clinic during the five working days of the week, before and during treatments. Air and surfaces were also examined at the end of the daily activity. A wide variation was found in microbial environmental contamination, both within the participating clinics and relative to the different sampling times. Microbial water contamination in Dental Unit Water Systems (DUWS) reached values of up to 26 × 10⁴ cfu/mL (colony forming units per millilitre). P. aeruginosa was found in 33% of the sampled DUWS and Legionella spp. in 50%. A significant decrease in the Total Viable Count (TVC) was recorded during the activity. Microbial air contamination showed the highest levels during dental treatments and tended to decrease at the end of the working activity (p < 0.05). Microbial buildup on surfaces increased significantly during the working hours. As these findings point out, research on microbial environmental contamination and the related risk factors in dental clinics should be expanded and should also be based on larger collections of data, in order to provide the essential knowledge aimed at targeted preventive interventions.