多带抗噪声语音识别算法研究

根据Flether等人的研究,基于感知独立性假设的子带识别方法被用于抗噪声鲁棒语音识别。本文拓展子带方法,采用基于噪声污染假定的多带框架来减少噪声影响。论文不仅从理论上分析了噪声污染假定多带框架在识别性能上的潜在优势,而且提出了多带环境下的鲁棒语音识别算法。研究表明：多带框架不仅回避了独立感知假设要求,而且与子带方法相比,多带方法能更好的减少噪声影响,提高系统识别性能。     

Operational aspects of adsorption air‐conditioner used in diesel locomotive

A locomotive cabin adsorption air‐conditioner has been equipped in #DF4B‐2369 locomotive; and has been successfully run for 2 years. It is powered by waste heat from the exhaust of the diesel engine. The influence on heat transfer is described by the equivalent heat transfer coefficient or thermal resistance of components inside the adsorber. The variation of adsorption capacity is expressed by a non‐equilibrium adsorption function. The dynamic heat transfer process of adsorption air‐conditioning system is treated with the lumped parameter method. Some typical running experimental results are present. The diesel engine rotating speed and locomotive speed influenced on the refrigeration system are discussed. The maximum mean refrigeration power is regarded as an objective function. Based on experiments and theoretical analysis, the running characteristics of the air‐conditioning system are optimized. Some techniques of performance improvement are suggested as well. Copyright © 2006 John Wiley & Sons, Ltd.     

MPTA型原油脱金属剂的工业应用

在对高金属含量原油进行初步评价的基础上，利用SH—Ⅰ型电脱盐试验仪对自主开发的MPTA型原油脱金属剂进行了原油脱金属的实验室研究。结果表明，当MPTA型脱金属剂加入量为250μg／g时，钙的脱除率可达97．4％，并且对其它金属元素，如镍、铁、钠、锰、铝和钒也有明显的脱除效果。该剂在山东恒源石油化工股份有限公司重交沥青车间500kt／a的电脱盐装置上进行原油脱金属工业试验的结果表明，经过二级电脱盐处理后，钙的脱除率达到99．1％，钠的脱除率为94．6％，铁的脱除率为82．9％，并可在一定程度上降低原油中镍和铜的含量。使用MPTA型原油脱金属剂显著降低了一、二级电脱盐装置的电场电流，有利于炼油厂的节能降耗。     

教育要有针对性管理要有强制性

分析高职学生思想状态的多层次性,提出以正面的思想教育和启发引导为主,同时加强规章制度的制约性,以提高教育管理工作的效果.     

Catalytic aminolysis of epoxide by alumina prepared from amine-protected Al precursor

The catalytic activities of alumina prepared from an Al alkoxide-amine adduct monomer for the reaction of cyclopentene oxide with piperidine was determined after various pretreatments, including calcination and exposure to moisture. They were compared with the activity of alumina prepared by the conventional hydrolysis method. It was found that the as-prepared sample from the alkoxide-amine monomer preparation was five times more active than a conventional preparation, suggesting that it has a higher density of surface Lewis acid sites. However, its activity was much more severely suppressed by exposure to moisture.     

A decision support system for interactive decision making - Part II: analysis and output interpretation

For pt.I see ibid., p.42-55 (2003). The development of a comprehensive decision support system, GMCR II, for the systematic study of real-world interactive decision problems is presented. The companion paper (Part I), discusses how GMCR II elicits, stores, and manages conflict models; here (Part II), the focus is on GMCR IIs analysis and output interpretation subsystems. Specifically, this paper describes the powerful and efficient analysis engine contained in GMCR II, its informative output presentation and interpretation facilities, and a number of follow-up analyses. Furthermore, an illustrative case study is used to demonstrate how GMCR II can be conveniently applied in practice.     

Techniques for high-frequency integrated test and measurement

This paper describes techniques for the on-chip measurement of high-frequency and/or high-bandwidth electrical phenomena in ultra large-scale integration environments. The techniques rely on the integration of multiple compact and robust electronic test devices, or cores, at various locations within an integrated circuit. The cores consist primarily of signal generators that approximate the output of a sigma-delta modulator using finite repetitious bit patterns and a small set of highly robust analog components. They are capable of digitizing on-chip signals at gigahertz rates even using low-cost manufacturing processes. Simple communication between the multiple cores enables the migration of many "board-level" type measurements down to the chip level.     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

On the effect of spatial variances in historical rainfall time series to CSO performance evaluation.

Historical, high-resolution rain series are the backbone of modern combined sewer overflow (CSO) structure design. These rain series are the input to the computational estimation of the performance of the measures with respect to CSO pollution abatement. However, those historical precipitation measurements are available at only a few locations. Frequently rain series have to be used from gauging stations at a significant distance. In order to judge and to compensate for this influence an estimate between rain characteristics and combined sewer outflow (CSO) performance indicators would be useful. In this paper such correlations have been sought for a collection of 37 rain series covering large areas of Europe. It was found that the mean annual rain volume can explain most of the variances for the performance indicators Number of overflows and CSO volume. For explaining the spatial differences in the efficiency of the CSO structure another rain characteristic, i.e. the maximum event with a return period of one year, is to be used.     

EBSP study of the annealing behavior of aluminum deformed by equal channel angular processing

Commercial purity aluminum (99.5%) was fabricated by equal channel angular pressing (ECAP) up to total accumulated strains of approx. 10. The annealing behavior of material deformed to total strains of approx. 1 and 10 was investigated, using heat treatments of 2 h at various temperatures from 100 to 500 °C. The microstructure of the annealed materials was characterized using the electron back-scatter pattern technique. A number of parameters were determined including the distribution and average values of both the boundary spacings and misorientations. For samples deformed to a total strain of 1, annealing resulted in discontinuous recrystallization. For samples deformed to a total strain of 10, annealing resulted in microstructures exhibiting characteristics of both uniform coarsening and, in a number of places, of discontinuous recrystallization. An attempt was made, based on the boundary spacing distributions, to separate these two components. The grain size after annealing was still however small, being just 6.4 μm after 2 h at 300 °C.