High-resolution photonics-based interference suppression filter with wide passband

A new topology for a photonic signal processor, which overcomes the basic recursive frequency response problem that limits the passband range, is presented. The structure is based on a new multiple-wavelength offset-cavity structure that is cascaded with a series of unbalanced delay line structures. This not only can synthesize a very narrow notch response with good shape factor but also permits a multifold extension of the free spectral range (FSR) and passband width. Results on the interference mitigation filter demonstrate a stopband of 1% of center frequency and a fourfold increase in the FSR and passband width, while also having a very small shape factor, in excellent agreement with predictions.     

Wavelength-tunable 40-GHz picosecond harmonically mode-locked fiber laser source

We demonstrate a novel 40-GHz mode-locked fiber laser that utilizes a single active device to provide both gain and mode-locking. The laser produces pulses as short as 2.2 ps, is tunable over a 27-nm band centered at 1553 nm, and exhibits long-term stability without cavity-length feedback control. The pulse train at 1556 nm was used in a 40-Gb/s transmission experiment over 45 km with a low 0.4-dB power penalty.     

Solutions to a combined problem of excessive hydrogen sulfide in biogas and struvite scaling.

The Woodman Point Wastewater Treatment Plant (WWTP) in Western Australia has experienced two separate problems causing avoidable maintenance costs: the build-up of massive struvite (MgNH4PO4. 6H2O) scaling downstream of the anaerobic digester and the formation of hydrogen sulfide (H2S) levels in the digester gas to levels that compromised gas engine operation and caused high operating costs on the gas scrubber. As both problems hang together with a chemical imbalance in the anaerobic digester, we decided to investigate whether both problems could be (feasibly and economically) addressed by a common solution (such as dosing of iron solutions to precipitate both sulfide and phosphate), or by using separate approaches. Laboratory results showed that, the hydrogen sulfide emission in digesters could be effectively and economically controlled by the addition of iron dosing. Slightly higher than the theoretical value of 1.5 mol of FeCl3 was required to precipitate 1 mol of dissolved sulfide inside the digester. Due to the high concentration of PO4(3-) in the digested sludge liquor, significantly higher iron is required for struvite precipitation. Iron dosing did not appear an economic solution for struvite control via iron phosphate formation. By taking advantage of the natural tendency of struvite formation in the digester liquid, it is possible to reduce the risk of struvite precipitation in and around the sludge-dewatering centrifuge by increasing the pH to precipitate struvite out before passing through the centrifuge. However, as the Mg2+/PO4(3-) molar ratio in digested sludge was low, by increasing the pH alone (using NaOH) the precipitation of PO4(3-) was limited by the amount of cations (Ca2+ and Mg2+) available in the sludge. Although this would reduce struvite precipitation in the centrifuge, it could not significantly reduce PO4(3-) recycling back to the plant. For long-term operation, maximum PO4(3-) reduction should be the ultimate aim to minimise PO4(3-) accumulation in the plant. Magnesium hydroxide liquid (MHL) was found to be the most cost-effective chemical to achieve this goal. It enhanced struvite precipitation from both, digested sludge and centrate to the point where more than 95% PO4(3-) reduction in the digested sludge was achieved.     

Reliability investigation of 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel

The authors have investigated the reliability performance of G-band (183 GHz) monolithic microwave integrated circuit (MMIC) amplifiers fabricated using 0.07-/spl mu/m T-gate InGaAs-InAlAs-InP HEMTs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel on 3-in wafers. Life test was performed at two temperatures (T/sub 1/ = 200 /spl deg/C and T/sub 2/ = 215 /spl deg/C), and the amplifiers were stressed at V/sub ds/ of 1 V and I/sub ds/ of 250 mA/mm in a N/sub 2/ ambient. The activation energy is as high as 1.7 eV, achieving a projected median-time-to-failure (MTTF) /spl ap/ 2 /spl times/ 10/sup 6/ h at a junction temperature of 125 /spl deg/C. MTTF was determined by 2-temperature constant current stress using /spl Delta/G/sub mp/ = -20% as the failure criteria. The difference of reliability performance between 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel and 0.1-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with In/sub 0.6/Ga/sub 0.4/As channel is also discussed. The achieved high-reliability result demonstrates a robust 0.07-/spl mu/m pseudomorphic InGaAs-InAlAs-InP HEMT MMICs production technology for G-band applications.     

Hot carrier analysis in low-temperature poly-Si thin-film transistors using pico-second time-resolved emission microscope

We have analyzed degradation of N-channel thin-film-transistor (TFT) under dynamic stress using a pico-second time-resolved emission microscope. We have successfully detected emission at pulse fall edge for the first time. Emission intensity increased with the decrease of pulse fall time. As the degradation depended on the pulse fall time, this dependence clearly illustrates that hot electrons are the dominant cause of the degradation under dynamic stress. Based on these dependences, we proposed a model considering electron traps in the poly-Si.     

Impact of lead-free soldering processes on the performance of signal relay contacts

Various legislations, rules and regulations in Europe [Restrictions of the use of certain hazardous substances in electrical and electronic equipment (ROHS)] and Japan (Recycling Law for Home Electric Appliances) have either targeted restrictions or a full ban on the use of lead, to be enforced from 2001, 2005, and 2006 onwards. Next to these regulations, marketing arguments are becoming more and more important for so called "GREEN" products. Up to now, mainly tin-lead alloys have been used in electronics. The process temperatures usually applied have been in the range of 230/spl deg/C. All currently discussed lead-free alternatives for professional electronics need process temperatures which are at least 30/spl deg/C higher. In addition, the process duration is significantly longer. The combination of higher process temperatures and longer duration together results in a significant thermal stress on the precision mechanics of the relay. In order to guarantee proper functioning of the relay after the solder process with maximum process temperatures of 255/spl deg/C, the dimensional changes of the plastic parts must be less than a few micrometers in order to guarantee stable contact forces. The outgassing of the used insulating and sealing materials must be minimal in order not to pollute or contaminate the contacts. With the lead-free version of the IM relay, an identical performance and the same reliability during electrical and climatic endurance tests can be expected, even though relays were processed with typical lead-free soldering processes with temperatures up to 255/spl deg/C.     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

A base-band NDS electrode configuration for HACT devices

Heterostructure Acoustic Charge Transport (HACT) devices have been fabricated with a new nondestructive sense (NDS) electrode structure that provides for the recovery of base-band signals without the use of an integrating capacitor. This electrode structure provides an output signal comprising an RF carrier at the SAW frequency, amplitude modulated by the sampled input signal which has been delayed by a period proportional to the output electrodes distance from the input diode. The output of the NDS electrode structure is subsequently demodulated to provide the base-band signal     

On the Possibility of Observing Third Sound on 3He

This paper focuses on the hydrodynamics of third sound on a superfluid ³ He film. We solve the hydrodynamical equations in the limit of thick films with weak interaction with the substrate. The surface tension at the free interface is shown to have a large effect on the third sound velocity and on the attenuation for frequencies larger than 1Hz. In the case of a diffusely scattering substrate a ripplon-like dispersion relation is found for this frequency range.