石化行业自动化控制仪表常见故障分析及其处理

介绍化工生产过程中仪表故障及其处理措施。     

莱钢冷轧轧机弯辊控制系统分析

对莱钢冷轧六辊单机架的弯辊系统进行研究与分析,介绍板形控制系统的原理和使用效果。     

基于模糊树逆方法的高超飞行器变质心控制

本文针对高超飞行器变质心姿态动力学模型所具有的高度非线性、多变量、强耦合特性,通过合理的简化,得到了一个耦合的非线性动力学系统;根据简化模型的特点,将该模型分为俯仰偏航通道模型和滚动通道模型,通道间耦合视为扰动.应用模糊树模型逼近俯仰偏航通道的逆模型,实现了俯仰偏航通道解耦线性化,对各线性子系统设计闭环控制器,实现了飞行器俯仰偏航通道姿态角的跟踪;应用预测变结构方法保证了滚动通道的快速稳定并且无抖振现象.最后,将该方法应用于高超飞行器姿态系统控制的仿真研究,表明了本文方法的有效性和可行性.     

A low power and small area all digital delay-locked loop based on ring oscillator architecture

A 133-500 MHz,5.2 mW @500 MHz,0.021 mm2 all digital delay-locked loop(ADDLL)is presented.The power and area reduction of the proposed ADDLL are achieved by implementing a high frequency ring oscillator(ROSC)to count the reference clocks such that the one-clock cycle delay chain and the phase detector in a conventional Master block are no longer needed.The proposed ADDLL has better immunity to PVT(process,voltage,and temperature)than most conventional DLLs,which do not update the control word signals after the locking process,since the control signals for slave delay line are updated in every 256 reference cycles.Fabricated in 0.13 um CMOS process,the measured RMS jitter is 10.83 ps at 500 MHz while the RMS jitter of the input signal is 9.97 ps.     

Multi-channel SAR imaging based on distributed compressive sensing

The rapid development of compressive sensing(CS)shows that it is possible to recover a sparse signal from very limited measurements.Synthetic aperture radar(SAR)imaging based on CS can reconstruct the target scene with a reduced number of collected samples by solving an optimization problem.For multi-channel SAR imaging based on CS,each channel requires sufficient samples for separate imaging and the total number of samples could still be large.We propose an imaging algorithm based on distributed compressive sensing(DCS)that reconstructs scenes jointly under multiple channels.Multi-channel SAR imaging based on DCS not only exploits the sparsity of the target scene,but also exploits the correlation among channels.It requires significantly fewer samples than multi-channel SAR imaging based on CS.If multiple channels offer different sampling rates,DCS joint processing can reconstruct target scenes with a much more flexible allocation of the number of measurements offered by each channel than that used in separate CS processing.     

热连轧过程自动化控制系统的应用

介绍日照钢铁1580mm热轧带钢过程控制系统的应用,以及系统配置、网络结构、中间件和应用软件功能。     

西门子PLC在合金钢棒材连轧机上的应用

介绍基于西门子S7-400PLC的控制系统,通过Ethernet、Profibus-DP、MPI网完成系统数据的采集、交换与监控,满足合金钢棒材轧制线高动态品质、高调速精度的要求。     

DCS安装调试规范

介绍DCS系统的安装、调试,阐述系统的接地规范、干扰在过程控制中的影响及预防、系统调试的具体方法和步骤。