Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

Cyclic oxidation response of multiphase niobium-based alloys

Cyclic oxidation tests were performed on multiphase Nb-based alloys containing silicide, Laves, and Nb solid solution phases. In particular, the oxidation resistance of six alloys with various compositions (Nb, Ti, Hf, Cr, Ge, and Si) and microstructures was characterized by thermal cycling from ambient temperature to a peak temperature that ranges from 900 °C to 1400 °C. Weight change data were obtained and the corresponding spalled oxides were collected and identified by X-ray diffraction. The results indicated that Nb-based alloys formed a mixture of CrNbO₄, Nb₂O₅, and Nb₂O₅ · TiO₂, with possibly small amounts of SiO₂ or GeO₂. The oxidation resistance was improved when CrNbO₄ formed instead of Nb₂O₅ and Nb₂O₅ · TiO₂. These results were used to assess the influence of microstructure and composition on the oxidation resistance of multiphase Nb-based alloys.     

Ice-slurry production using direct contact heat transfer

An ice slurry generation system was developed using direct contact heat transfer between water and the coolant, Fluroinert FC-84. The location of the coolant nozzle is an important design consideration to avoid clogging due to freezing of water. An ice fraction of up to about 40 percent was obtained with the nozzle located at the bottom of the ice slurry tank and the jet directed upwards into the water. Two simplified model were developed to extract the heat transfer coefficient between the coolant drops and the water. The first model requires as input the average drop diameter and the residence time while the second model uses the measured drop diameter distribution. The estimated heat transfer coefficients are much smaller than those computed using single-sphere correlations.     

Control of calcium hexaluminate grain morphology in in-situ toughened ceramic composites

The influence of processing conditions on the morphology of calcium hexaluminate (CA₆) grains in Al₂O₃: 30 vol% CaO·6Al₂O₃ (CA₆) ceramic composites was investigated. Specimens were prepared by in-situ reaction sintering using precursor powders of alumina, and either calcium carbonate or calcium oxide. In some samples, 1 vol% anorthite glass was added as a sintering aid. X-ray diffraction was used to study the phase development in the as-calcined and sintered states. The resultant microstructures were characterized using both scanning electron microscopy (SEM), and imaging secondary ion mass spectrometry (SIMS). It was found that the CA₆ grains developed a platelike morphology when CaCO₃ was used as the starting calcium-rich powder. In contrast, samples prepared using CaO resulted in equiaxed CA₆ grains. This result was observed to be independent of the anorthite glass addition. The findings are rationalized in terms of distinct CA₆ reaction mechanisms, resulting from differences in the reactivity of the powders during the early stages of calcining.Cement Nomenclature C CaO - A Al₂O₃     

Gordon-Haus timing jitter reduction in dispersion-managed solitoncommunications

An analytic theory is presented which demonstrates that the noise induced Gordon-Haus timing jitter in arbitrary dispersion-managed transmission systems is reduced by the power-enhancement factor required to support a dispersion-managed solitons provided the path-average soliton period is much greater than the dispersion-map period. The analysis further predicts the behaviour of the amplitude, width, and quadratic chirp fluctuations due to the amplified spontaneous emission (ASE) noise     

An eight‐node hybrid‐stress solid‐shell element for geometric non‐linear analysis of elastic shells

This paper presents eight‐node solid‐shell elements for geometric non‐linear analysis of elastic shells. To subdue shear, trapezoidal and thickness locking, the assumed natural strain method and an ad hoc modified generalized laminate stiffness matrix are employed. A selectively reduced integrated element is formulated with its membrane and bending shear strain components taken to be constant and equal to the ones evaluated at the element centroid. With the generalized stresses arising from the modified generalized laminate stiffness matrix assumed to be independent from the ones obtained from the displacement, an extended Hellinger–Reissner functional can be derived. By choosing the assumed generalized stresses similar to the assumed stresses of a previous solid element, a hybrid‐stress solid‐shell element is formulated. Commonly employed geometric non‐linear homogeneous and laminated shell problems are attempted and our results are close to those of other state‐of‐the‐art elements. Moreover, the hybrid‐stress element converges more readily than the selectively reduced integrated element in all benchmark problems. Copyright © 2002 John Wiley & Sons, Ltd.     

Analysis of adaptive routing schemes in multirate loss networks

As technology evolves, it is now feasible to implement sophisticated adaptive routing schemes on networks which support different kinds of services with heterogeneous bandwidth characteristics. Adaptive routing can increase the network throughput by routing calls to less congested paths. It can also be used to bypass transmission facility failures. In this paper, we analyze and compare two adaptive routing schemes. The first is called theMaximum mean time to blocking (MTB) routing which is based on themean time to blocking measure of a link. This measure captures the traffic rates, bandwidth characteristic and link capacity information and reflects more accurately the congestion status of different paths. The second is theM ² routing, which is a modification of the least loaded routing (LLR). Aggregation of link status information can significantly reduce signalling traffic. We show in this paper that with properly designed aggregation, the aggregatedM ² and MTB routings can have performance that approach that of the non-aggregated schemes. The use of complete sharing and restricted access policies together with trunk reservation control in multirate loss networks are also studied.