Air Filtration and Radon Decay Product Mitigation

Air cleaning as a means of mitigating the risks arising from exposure to indoor radon progeny has been evaluated in a single-family house in the north eastem US. using an automated, semi-continuous activity-weighted size distribution measurement system. The measurements included radon concentration, condensation nuclei count, and activity-weighted size distribution of radon decay products. Measurements were made in the house with and without an operating air filtration system and with various particle sources common to normal indoor activities operating. Aerosols were generated by running water in a shower, candle burning, cigarette smoking, vacuuming, opening doors, and cooking. Using a room model, the changes in attachment rates, average attachment diameters, and deposition rates of the unattached fraction with and without the air cleaning system were calculated. In the presence of active aerosol sources, the air filtration unit typically reduced the concentration of particles within the hour following the end of particle generation. After candle burning, cigarette smoking, and vacuuming in the bedroom, the reductions of PAEC by air filtration are about 60% with the air filtration system operating in the bedroom. During cooking in the kitchen, the reductions of PAEC in the bedroom with the air filtration system were about 40%. However, for all cases the dose reductions were smaller than the particle and PAEC reductions. For those particles that were generated within the bedroom, there was a 20% to 50% reduction in dose. In the case of cooking where the door was open and particles infiltrated from the rest of the house, the dose reduction was only 5% on average and appears to be insignificant. Thus, the dose reductions were h e r than the reductions in activity concentration, but there were no cases where the estimated dose actually increased.     

Reply to comments on “Error rate performance of theprojection code”

The authors reply to the comments by Koppelaar and Tolhuizen (see ibid. vol.46, no.9, p.573, 1998). They state that the optimum choice of the slopes used to perform the encoding process in a projection code always results in maximizing the minimum Hamming distance so that d=2 ^r     

感光乳剂熔化三要素对熔化供料的影响

本文讨论了温度、搅拌和时间三要素对感光乳剂和工艺过程的影响，指出了上述影响的后果和严格过程控制的重要性，提出克服影响的措施。     

三维Fuzzy数字拓扑及应用(Ⅰ)

本文引入L-,l-连通度的概念,把Rosenfeld等人建立的三维数字拓扑模糊化;并在三维地震处理中找到了它的应用模型.     

Assessment of underground cable ratings based on distributed temperature sensing

Numerous power utilities have installed advanced distributed temperature sensing (DTS) systems to measure the temperature of underground cables. This paper presents a general procedure for real-time assessment of underground cable ratings based on DTS. After the identification and location of hot spots on a cable, the cable installation data, load, and DTS-recorded temperature over a period of time are used to estimate soil thermal parameters and assess cable ratings under normal and overloading conditions. In order to accurately estimate soil thermal parameters, a combined technique of the finite-element method and gradient-based optimization is used. The technique was validated in the laboratory and applied to a rating assessment of a 230-kV/500-MVA cable circuit. The assessed continuous and emergency ratings are helpful in improving the operation of this circuit.     

Reliability Modeling and Analysis of Communication Networks with Dependent Failures

This paper presents a new model to study the reliability of communication networks in which link failures are statistically dependent. The approach tries to identify and model explicitly the events that cause communication link failures. No conditional probabilities are needed, and so two major difficulties inherent to them, namely, an exponential number of conditional probabilities to deal with and a consistency requirement to satisfy, are avoided. For reliability computations, some existing algorithms for finding network reliability can be used with minor modifications and no significant increase in computational complexity.     

X射线聚束透镜原理及其应用

本文阐述了一种新型的Ｘ射线聚束装置─—Ｘ射线透镜的聚束原理。给出了透镜的基本设计方法，并对它应用于Ｘ射线光刻研究领域的前景作了展望。