Constrained Drying of Aqueous Yttria-Stabilized Zirconia Slurry on a Substrate. I: Drying Mechanism

Aqueous yttria-stabilized zirconia slurry was cast on a substrate to form wet coatings. Both weight loss and thickness reduction were measured, during the drying process. Lateral drying was observed by in situ monitoring of the coating surface. The drying kinetics were classified as an initial constant rate period (CRP), followed by a falling rate period (FRP). Thickness reduction occurred in the CRP stage, and was uneven across the coating because of lateral flow. As tensile stresses developed within the coating because of the constrained volume shrinkage, crack formation and propagation occurred in the FRP stage and affected the drying rate.     

基于DTC的井下架线式电机车变频调速装置设计与应用

分析了井下架线式电机车运行现状及存在的维护量大、维护成本高、故障率高等问题.设计了一种基于DTC的电机车电机变频调速装置,现场应用情况表明其具有起动力矩大、维护量小、故障率低、节约成本的优点.指出了应用DTC变频调速技术改造传统的矿用架线式电机车直流传动系统的必要性及应用前景.     

ZL2.8/194型回热式气体制冷机故障分析与处理

对ZL2．8／194型回热式气体制冷机构造进行简要的叙述，分析了四个缸压力不平衡的故障原因，介绍了常见典型故障的处理办法，并提出维修时几点注意事项。     

硫含量对钴钼型耐硫脱氧剂的脱氧活性影响

研究了工艺气中硫含量对钴钼型耐硫脱氧剂脱氧活性的影响。通过常压微反 -色谱装置测定脱氧剂的本征脱氧活性 ,加压原粒度反应器测定脱氧剂的表观脱氧活性 ,结合实际经验确定了耐硫脱氧剂所需的最低硫含量。还讨论了温度、压力、空速对耐硫脱氧剂脱氧活性的影响。结果表明 ,耐硫脱氧剂完全能满足耐硫变换工艺的要求 ,而且有耐硫变换的作用 ,并对耐硫变换催化剂起到保护作用     

合成镁白云石砂的研制与应用

选用优质轻烧白云石、轻烧菱镁石为原料,经干法消化、高温煅烧,制得杂质含量2.66％、体密>3.28g/cm~3的合成镁白云石砂。用合成镁白云石砂制得CaO MgO>97％,总杂质含量2.11％的高纯合成镁白云石砖,在太原钢铁公司AOD炉第一次试用,最高炉令达36炉次。     

节能型铝合金连续熔化－去气炉

介绍一种用于铝合金的连续熔化－去气的节能装置。着重讨论了此装置的结构和操作要点以及影响铝合金质量的因素。文中对比了此装置与传统阶段式熔化系统操作上的异同点。分析了连续熔化炉的经济效益。研究表明毛坯耗电量下降８５％，并可减少合金元素加入量以及坩埚和加热元件的消耗。铸件质量合格。     

基于超声波的围岩松动圈实时监测系统设计

实时地掌握围岩松动圈的范围对矿藏的安全生产具有重要的意义。利用超声波探测的灵活性和准确性,本文提出了一种基于超声波的围岩松动圈监测系统设计方法。此方案利用超声波在岩体中的传播速度与岩体的受力状态和裂隙程度的关系来实时地监测围岩松动圈的情况,具有方便、灵活、易于操作等特点。     

A simple and cost-effective method for fabrication of integrated electronic-microfluidic devices using a laser-patterned PDMS layer

We report a simple and cost-effective method for fabricating integrated electronic-microfluidic devices with multilayer configurations. A CO₂ laser plotter was employed to directly write patterns on a transferred polydimethylsiloxane (PDMS) layer, which served as both a bonding and a working layer. The integration of electronics in microfluidic devices was achieved by an alignment bonding of top and bottom electrode-patterned substrates fabricated with conventional lithography, sputtering and lift-off techniques. Processes of the developed fabrication method were illustrated. Major issues associated with this method as PDMS surface treatment and characterization, thickness-control of the transferred PDMS layer, and laser parameters optimization were discussed, along with the examination and testing of bonding with two representative materials (glass and silicon). The capability of this method was further demonstrated by fabricating a microfluidic chip with sputter-coated electrodes on the top and bottom substrates. The device functioning as a microparticle focusing and trapping chip was experimentally verified. It is confirmed that the proposed method has many advantages, including simple and fast fabrication process, low cost, easy integration of electronics, strong bonding strength, chemical and biological compatibility, etc.     

基于Cortex-M3的多功能楼宇控制系统网关节点设计

针对目前大多公司的楼宇日常办公耗电无法做到智能节能控制,提出了一种基于多功能网关节点的集中控制解决方案。设计中提出利用基于Cortex-M3的LPC1766作为网关节点,并且集成DHT11温湿度传感器,光线传感器和继电器控制电路等。通过RS485和终端节点通讯并且通过以太网与上位机通讯.最终实现远程楼宇节能控制的三层体系解决方案。