Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

Advanced disturbance observer design for mechanical positioning systems

Disturbance-observer (DOB)-based controller design is one of the most popular methods in the field of motion control. In this paper, the generalized disturbance compensation framework, named the robust internal-loop compensator (RIC) is introduced and an advanced design method of a DOB is proposed based on the RIC. The mixed sensitivity optimization problem, which is the main issue of DOB design, is also solved through the parametrization of the DOB in the RIC framework. Differently from conventional methods, the Q-filter is separated from the mixed sensitivity optimization problem and a systematic design law for the DOB is proposed. This guarantees the robustness and optimality of the DOB and enables the design for unstable plants.     

NSA-500-1型氩弧焊机VD9不同接法对引弧和稳弧的影响

从一起NSA－500－1型氩弧焊机故障，分析其高压脉冲旁路二极管VD9不同接法对引弧、稳弧及设备安全的影响。     

氟塑料—石墨板式换热器在高温强腐蚀换热工况中的应用

通过氟塑料－石墨板式换热器在化纤生产中高温强腐蚀换热工况中的实际应用，并与常规换热器的使用情况的对比分析，阐述了这种新型换热设备的特点。     

邻—(4—乙基苯甲酰基)苯甲酸的研究

本文阐述了通过Friedel-Crafts反应合成邻-(4-乙基苯甲酰基)苯甲酸的方法.研究了影响产物质量的因素,提出了适宜的工艺条件.     

Trends and variations in neonatal length of in-hospital stay in Canada

The objectives of this study were to evaluate the possible mechanisms involved in prolongation of bleeding time in pre-eclamptic patients receiving a magnesium sulfate infusion to prevent convulsions. Eighteen pre-eclamptic patients near term or at term (4 cases 33 to 35 weeks; the remainder > 36 weeks) were studied. Fifteen of them received magnesium sulfate infusion; 3 did not and served as controls. Bleeding time (modified Ivy method with Surgicutt), platelet count, platelet aggregation pattern, as well as serum arachidonic acid metabolites [thromboxane B2 (TxB2) and 6-Keto-prostaglandin F1 alpha (6-Keto-PGF1 alpha)] werde done on admission to the labor floor (before magnesium infusion) and repeated at discontinuation of the infusion, 12-24 hours postpartum; the controls received the second test 24 hours postpartum. Thirteen of 15 patients receiving magnesium sulfate had an increase in bleeding time from an average of 6 minutes 31 seconds to 11 minutes 56 seconds, an 82% rise (p < 0.004). In 2 there was a decrease. Among the 3 controls the averages were 6 minutes 38 seconds and 6 minutes 3 seconds. The total magnesium given ranged from 52.5 to 145 grams. Platelet counts averaged 251,000/mm3 (range 145,000-519,000). Platelet aggregation pattern done in 11 patients and was normal and unchanged after magnesium in 10 of the patients with increased bleeding time and one control. TxB2 and 6-Keto-PGF1 alpha levels did not change significantly either after magnesium administration (688 and 135 pgm/ml, to 654 and 117) or in controls (695 and 230 pgm/ml, to 445 and 225). Likewise, the ratio of these 2 substances did not change in either group (6.3 to 6.6, and 4.2 to 2.2). There was no correlation between duration of infusion or total magnesium given and directions of small changes observed. This study confirms a prior preliminary observation that magnesium sulfate infusion, as currently used to prevent eclamptic convulsions, induces a significant prolongation of bleeding time. This effect is mediated neither by changes in platelets count or aggregation pattern, nor by changing the level or ratios of serum arachidonic acid metabolites (TxB2 and 6-Keto-PGF1 alpha). Further studies are needed to clarify the mechanism of this clinically important observation of increased bleeding following magnesium sulfate infusion.     

Characterization method of thermomechanical parameters for microelectronic materials

Reliability of thermomechanical simulations is critically linked to the accuracy of the mechanical properties that govern the behaviour of structure, like Young's modulus (E) and coefficient of thermal expansion (CTE). For many cases, the values found in literatures are dealing with bulk properties without detailed information on temperature effects. To address such issues, it is necessary to measure the materials parameters as a function of temperature. The measurement of CTE is usually accomplished by evaluating the thermal deflections of a subjected material layer deposited on a substrate, providing that E is known at a specific temperature of experiment. A bilayer method, based on theory of elasticity, is proposed to determine both E and CTE for a given temperature with a good resolution. This paper presents the theoretical analysis, the design and process of the microsystem test structures, and the main calculation results.     

End-User Computing in a CASE Environment

Computer-aided software engineering (CASE) tools are currently being used by IS professionals rather than by users. No matter how effective these tools may be, however, they will not be able to assist in the reduction of application backlogs without supporting user-driven applications. This article examines characteristics of a CASE environment from the various perspectives of decision support, identifies the advantages and limitations of end-user computing in this environment, and suggests how IS managers can realize the potentials of CASE for user applications.     

基于CDMA智能网平台的增值业务--"位置服务"

本主要介绍基于CDMA智能网平台的一种增值业务——“位置服务”，阐述这个业务的网络结构、涉及到的技术问题和解决方案，并将这个整体思路投入到开发业务中去。