Control of calcium hexaluminate grain morphology in in-situ toughened ceramic composites

The influence of processing conditions on the morphology of calcium hexaluminate (CA₆) grains in Al₂O₃: 30 vol% CaO·6Al₂O₃ (CA₆) ceramic composites was investigated. Specimens were prepared by in-situ reaction sintering using precursor powders of alumina, and either calcium carbonate or calcium oxide. In some samples, 1 vol% anorthite glass was added as a sintering aid. X-ray diffraction was used to study the phase development in the as-calcined and sintered states. The resultant microstructures were characterized using both scanning electron microscopy (SEM), and imaging secondary ion mass spectrometry (SIMS). It was found that the CA₆ grains developed a platelike morphology when CaCO₃ was used as the starting calcium-rich powder. In contrast, samples prepared using CaO resulted in equiaxed CA₆ grains. This result was observed to be independent of the anorthite glass addition. The findings are rationalized in terms of distinct CA₆ reaction mechanisms, resulting from differences in the reactivity of the powders during the early stages of calcining.Cement Nomenclature C CaO - A Al₂O₃     

AC measurements of the minimum longitudinal resistance of a QHEsample from 10 Hz to 10 kHz

AC measurements of the longitudinal resistance, R_xx, of a quantum Hall effect (QHE) sample have been made in a frequency range from 10 Hz to 10 kHz. The results show no frequency effect on the minimum value of R_xx corresponding to the quantum numbers i=2 and i=4, within the measurement resolution of 0.5 mΩ. Therefore, the influence of frequency on the value of the quantized Hall resistance, R_H, should not exceed a few parts in 10⁹ . Some unwanted effects detected during the development of the resistance bridge have been pointed out     

Coriolis effects in the dynamics of a rotating elastic structure

Summary Small oscillations of a rotating elasticum with a mass at the free end are investigated with Poincaré-Lindstedt series. It is shown that the mass moves on a figure-eight shaped curve in a direction determined by the sign of the angular velocity and hence that the Coriolis force influences the motion.     

Process optimization and related material properties of silicon films produced by laser-induced chemical vapour deposition from silane

Laser-induced chemical vapour deposition of silicon films on SiO₂/Si (1 0 0) and Si (1 0 0) substrates was studied using ArF laser irradiation of silane/argon gas mixture in parallel to the substrate. The optimal deposition conditions were specified by examination of film morphology at a wide range of irradiation and process parameters. At optimal conditions, specular films were obtained with no powder formation. The effect of deposition parameters, such as laser energy and repetition rate, on the deposition rate and the related film quality, was investigated.     

Melt-extracted oxide ceramic fibres — the fundamentals

A melt-extraction technique, using a sharpened molybdenum wheel, has been used to produce fine oxide ceramic fibres. Wetting of the molybdenum wheel by molten ceramic is a key parameter in the melt-extraction process. Two types of fibre are generally obtained, depending on the extraction speed. At very low wheel speed, fine and uniform fibres of high quality are produced. However, when the wheel speed exceeds a critical velocity, Rayleigh waves are formed on the free surface of the fibres. Moreover, the average fibre thickness first increases with the wheel velocity, then passes through a maximum, decreasing at high velocity. This thickness variation is discussed in terms of both surface tension and viscosity of the liquid ceramics.     

Effect of type of processing on the microstructural features and mechanical properties of Al-Cu/SiC metal matrix composites

In this study, an aluminum based metallic matrix (Al-2wt.% Cu) was reinforced with SiC particulates using a conventional casting technique and a new disintegrated melt deposition technique. Microstructural characterization studies conducted on the samples taken from disintegrated melt deposition technique revealed a more uniform distribution of SiC particulates and good interfacial integrity between SiC particulates and metallic matrix when compared to the conventionally cast composite samples. Results of ambient temperature mechanical tests demonstrate an increase in 0.2% YS and ultimate tensile strength of samples taken from disintegrated melt deposition technique when compared with the unreinforced and conventionally cast composite samples. The results of microstructural characterization and mechanical testing were finally rationalized in terms of the nature of processing technique employed to reinforce Al-2wt.% Cu metallic matrix with SiC particulates.     

Using internal fibre geometry to improve the performance of pin-loaded holes in composite materials

The anisotropic nature of fibre reinforced composites leads to large stress concentrations around pin-loaded holes through standard weave cloths. Proper understanding of how this anisotropic nature affects the load distribution around holes can be utilised to reduce these concentrations if sufficient thought is given to the internal fibre geometry near to the hole. Such local reinforcements need not be highly complex and can be readily produced without excessive effort, producing significant improvements in performance.