基于嵌入式Linux的远程数据采集系统

以嵌入式微控制器为核心,将传感器网络收集来的数据通过无线电发射机发送到远程接收机,从而实现远程数据采集.系统的优势是充分利用了短波无线链路资源,适合于工作在无人区等场合.以ARM7为控制器,功耗小,性能稳定,维护方便;通信方式采用串口通信,连接线少,实现相对简单.系统设计主要应用嵌入式μCLinux系统设计、无线电发射、调制解调器等方面的知识,文中给出了调制解调器拨号协议、系统原理和软件流程等.     

宏蜂窝模型的传播模型校正研究

详细介绍了 宏蜂窝传播模 型校正的基本操作流程 结果分析及注意事项 对工程 ,人员了解和开展模型校正工作有一定的指导作用 。     

国内3G网络共享问题之研究

随着国内3G时代的来临，3G网络共享问题越来越受到人们的关注。本文结合国内移动通信的现状，着重分析了3G网络共享的模式及经济效益，论述了3G网络共享的相应策略。     

Analysis and comparison of two-dimensional permanent-magnet arrays for planar motor

This paper investigates three kinds of permanent-magnet arrays used in planar motors with polarity centers distributed in the lattices of a matrix. The magnetic field of every kind of magnet array is analyzed by analytical methods. First, we give a Laplace equation of magnetic scalar potential and a series of boundary conditions. Then, we derive the analytical expressions of magnet field strength and magnet flux density in the air gap of each kind of magnet array by the method of separation of variables. Finally, we compare the three types of magnet arrays on the basis of the analytical solutions.     

Thomas Fincke und die <Emphasis Type="Italic">Geometria rotundi</Emphasis>

Thomas Fincke (January 6^th, 1561–April 24^th, 1656), born in Flensburg (Germany), was one of the very most important and significant scientists in Denmark during the seventeenth century, a mathematician and astrologer and physician in the beginning of modern science, a representative of humanism and an influentual academic organizer. He studied in Strasbourg (since 1577) and Padua (since 1583) and received his M.D. in Basel (1587), he practised as a physician throughout his life (since 1587 or 1590) and became a professor at Copenhagen (1591). But he was best known because of his Geometriae rotundi libri XIIII (1583), a famous book on plane and spherical trigonometry, based not on Euclid but on Petrus Ramus. In this influentual work, in which Fincke introduced the terms tangent and secant and probable first noticed the Law of Tangents and the so-called Newton-Oppel-Mauduit-Simpson-Mollweide-Gauss-formula, he showed himself to be „abreast of the mathematics of his time“.      

Fault-aware Communication Mapping for NoCs with Guaranteed Latency

As feature sizes shrink, transient failures of on-chip network links become a critical problem. At the same time, many applications require guarantees on both message arrival probability and response time. We address the problem of transient link failures by means of temporally and spatially redundant transmission of messages, such that designer-imposed message arrival probabilities are guaranteed. Response time minimisation is achieved by a heuristic that statically assigns multiple copies of each message to network links, intelligently combining temporal and spatial redundancy. Concerns regarding energy consumption are addressed in two ways. First, we reduce the total amount of transmitted messages, and, second, we minimise the application response time such that the resulted time slack can be exploited for energy savings through voltage reduction. The advantages of the proposed approach are guaranteed message arrival probability and guaranteed worst case application response time.     

EPP在便携式数据采集系统中的应用

分析了并口处于EPP(增强型并行端口)模式时和单片机进行数据交换的原理.介绍了有关EPP的基本特性、信号定义、操作模式及其程序设计方法,设计了基于EPP协议的便携式数据采集系统,给出了技术解决方案,讨论了系统的硬件接口电路和软件编程.方案具有可靠性高、速度快、软硬件设计简捷等优点.     

碳纤维复合材料柔性连续抽油杆开发及应用

碳纤维柔性连续抽油杆选用高性能碳纤维 ,以环氧树脂胶液为基体材料 ,添加一定配比的固化剂、促进剂和脱模剂 ,采用拉挤成型工艺制成 ,其开发的关键技术是连续成型、连接接头和安全保险装置。现场应用试验表明 ,TXC— 1、TXC— 2、TXC— 3三种规格的碳纤维柔性连续抽油杆能可靠应用于泵挂深度分别为 12 0 0、 180 0、 30 0 0m的直井和斜井中 ,实测比钢抽油杆节电 ,日产油量提高 。节能增产效果显著。     

Copper-zirconium tungstate composites exhibiting low and negative thermal expansion influenced by reinforcement phase transformations

A fully-dense Cu-75 vol pct ZrW₂O₈ metal matrix composite was fabricated by hot isostatic pressing of Cu-coated ZrW₂O₈ particles. A small amount of the high-pressure γ-ZrW₂O₈ phase was created during the cooldown and depressurization following densification; near complete transformation to γ-ZrW₂O₈ was achieved by subsequent cold isostatic pressing. The thermal expansion behavior of the composite between 25°C and 325°C was altered by the cold isostatic pressing treatment, and also depended on the length of time that had passed between thermal cycles. The measured thermal expansion coefficients within specific temperature ranges varied from −6·10⁻⁶ K⁻¹ to far above the thermal expansion coefficient of the copper matrix. The complex temperature-dependent expansion/contraction behavior could be justified by considering the evolution of phase transformations taking place in the ZrW₂O₈ phase, which were observed by in-situ synchrotron X-ray diffraction measurements.     

Improving Cost Estimates of Construction Projects Using Phased Cost Factors

Central to cost-based competition is the capability to accurately predict the cost of delivering a project. Most literature on cost estimation focuses on specific estimation methods as generic techniques and little attention has been paid to the unique requirements at each project stage. This note attempts to identify the critical factors for effective estimation at various stages of typical construction projects. Drawing from organization control theory and cost estimating literature, this note develops a theoretical framework that identifies the critical factors for effective cost estimation during each project phase of a conventional construction project. The underlying logic is that as a cost estimating effort progresses, both task programmability and output measurability improve. As a result, control effort will shift from input-oriented control to a combination of output and behavior control.