共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。     

Accurate higher-order analytical approximate solutions to nonconservative nonlinear oscillators and application to van der Pol damped oscillators

In general, this paper deals with general nonlinear oscillations of a nonconservative and single degree-of-freedom system with odd nonlinearity and, in particular, it presents accurate higher-order analytical approximate solutions to van der Pol damped nonlinear oscillators having odd nonlinearity and the Rayleigh equation. By combining the linearization of the governing equation with harmonic balancing and the method of averaging, we establish accurate analytical approximate solutions for the general weakly damped nonlinear systems. Unlike the classical harmonic balance method, simple linear algebraic equations instead of nonlinear algebraic equations are obtained upon linearization prior to harmonic balancing. The combination of these two methods results in very accurate transient response of the periodic solution. In addition and for the first time, this paper also presents a method for deducing fourth-, fifth- and higher-order linearized governing equations from the lower-order equations without the requirement of formulating the problem from the first principle. Three examples including the van der Pol damped nonlinear oscillator are presented to illustrate the excellent agreement with approximate solution using the exact frequency.     

Friction and wear of Inconel 690 and Inconel 600 for steam generator tube in room temperature water

In the steam generators of nuclear power plants, the flow of cooling water can cause the tubes to vibrate, resulting in fretting wear damage due to contacts between these tubes and their supports. The tubes are made of Inconel 690 and Inconel 600 and the supports are made of STS 304. In this paper, fretting wear tests in water were performed using the materials Inconel 690 and Inconel 600 in contact with STS 304. Fretting tests using a cross-cylinder type set up were conducted under various vibrating amplitudes and applied normal loads in order to measure friction forces and wear volumes. Also, conventional sliding tests using a pin-on-disk type set up were carried out to compare these test results.In the fretting tests, friction force was found to be strongly dependent on normal load and vibrating amplitude. Coefficients of friction decreased with an increase in the normal load and a decrease in the vibrating amplitude applied. Also, the wear of Inconel 600 and Inconel 690 was predicted using a work rate model. Depending on the normal load and vibrating amplitude applied, distinctively different wear mechanisms and often drastically different wear rates occurred. It was found that the fretting wear coefficients for Inconel 600 and Inconel 690 were 9.3×10⁻¹⁵ and 16.2×10⁻¹⁵ Pa⁻¹, respectively. This study shows that Inconel 690 can result in lesser friction forces and exhibits less wear resistance than Inconel 600 in room temperature water.     

Frames of Reference in Mobile Augmented Reality Displays.

In 3 experiments, the authors investigated spatial updating in augmented reality environments. Participants learned locations of virtual objects on the physical floor. They were turned to appropriate facing directions while blindfolded before making pointing judgments (e.g., "Imagine you are facing X. Point to Y"). Experiments manipulated the angular difference between the learning heading and the imagined heading and between the actual heading and the imagined heading. The effect of actual-imagined on pointing latency was observed for naive users but not for users with brief training or instructions concerning the fact that objects can move with body movements. The results indicated that naive users used an environment-stabilized reference frame to access information arrays, but with experience and instruction the nature of the representation changed from an environment stabilized to a body stabilized reference frame. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A positive‐working photosensitive polyimide based on thermal cross‐linking and acidolytic cleavage

A novel positive‐working photosensitive polyimide (PSPI) based on a poly(hydroxyimide) (PHI), a crosslinking agent having vinyl ether groups, and a photoacid generator (PAG) was prepared. The PHI as a base resin of the three‐component PSPI was synthesized from 4,4′‐oxydiphthalic anhydride and 2,2′‐bis(3‐amino‐4‐hydroxyphenyl)hexafluoropropane through ring‐opening polymerization and subsequent thermal cyclization. 2,2′‐bis(4‐(2‐(vinyloxy)ethoxy)phenyl)propane (BPA‐DEVE) was used as a vinylether compound and diphenyliodonium 5‐hydroxynaphthalene‐1‐sulfonate was used as a PAG. The phenolic hydroxyl groups of the PHI and the vinyl ether groups of BPA‐DEVE are thermally crosslinked with acetal structures during prebake step, and the crosslinked PHI becomes completely insoluble in an aqueous basic solution. Upon exposure to UV light (365 nm) and subsequent postexposure bake (PEB), a strong acid generated from the PAG cleaves the crosslinked structures, and the exposed area is effectively solubilized in the alkaline developer. The dissolution behavior of the PSPI containing each 11.5 wt % of BPA‐DEVE and of the PAG was studied after UV exposure (365 nm) and PEB. It was found that the difference in dissolution rates between exposed and unexposed areas was enough to get high resolution. A fine positive pattern with a resolution of 5 μm in a 3.7‐μm‐thick film was obtained from the three‐component PSPI. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Tribological behavior of PTFE nanocomposite films reinforced with carbon nanoparticles

Carbon-based nanoparticles synthesized by heat treatment of nanodiamond in the temperature range of 1000–1900 °C were added to PTFE film to investigate the structural effect of the carbon particles on the tribological properties of PTFE composite film. Carbon-based nanoparticles were prepared by milling with micron sized beads in chemically treated water before their addition to PTFE film. The wear and frictional properties of PTFE nanocomposite film were measured by the ball on plate type wear test. The wear resistance of PTFE film was found to be enhanced by the addition of 2 wt% of carbon nanoparticles. The wear coefficient of PTFE film was decreased from 16.2 to 3.5 × 10⁻⁶ mm³/N m by the addition of carbon-based nanoparticles heat-treated at 1000 °C. Increasing the heating temperature of the nanodiamonds caused the extent of aggregation and particle size to increase. The wear resistance of PTFE nanocomposite film was enhanced by the addition of nanodiamonds heat-treated at 1000 °C, but decreased when the heat treatment temperature of carbon nanoparticles was further increased. Tribological behavior of PTFE nanocomposite films depending on the types of carbon nanoparticles were explained based on the structural, physical and chemical modification of carbon nanoparticles.     

Effects of chemical and plasma surface treatments on the O2-annealed Ni/Au contact to p-Gan

The effects of boiling Aqua Regia (AQ), N₂/Cl₂ plasma followed by AQ and O₂ plasma followed by AQ surface treatments prior to Ni/Au (20 nm/20 nm) metallization to p-GaN:Mg (∼ 3 × 10¹⁷ cm^− 3) have been investigated. N₂/Cl₂ plasma was employed in a bid to lower the Ga/N and O/Ga ratios of the GaN surface to improve the contact properties to p-GaN, while O₂ plasma was employed as an alternative to incorporate O into the Ni/Au system. Results show that a low Ga/N ratio does not necessarily correspond to a better contact. The positive effect of O₂ over N₂ anneal is observed only for the AQ-treated sample, although the mechanisms responsible for its positive effect: NiO formation and Ni/Au layer-reversal were observed for all O₂-annealed contacts. We conclude that the effect of O₂ anneal on the Ni/Au contact is dependant on the p-GaN surface prior to metallization.     

Design of electrically small ground planes for HF ground wave transmission

Electrically small spiral ground planes for a monopole and an electrically small antenna have been designed for HF ground wave transmission. Prototype ground planes have been built and tested. For the monopole, the transmission loss of the designed ground plane is 6 dB better than that of the same size ground radials. For the electrically small antenna, the transmission loss of the designed ground plane is 7 dB better than that of the same size solid ground plane at the antenna's operating frequency.