SEQUENTIAL LOOP CLOSING IDENTIFICATION OF MULTIVARIABLE PROCESSES USING THE BIASED RELAY FEEDBACK METHOD

Each controller in multiloop control systems for multivariable processes can be tuned sequentially with the ultimate information for the paired input and output while former loops have been closed, and hence, single-input single-output autotuning methods can be applied. In this sequential autotuning for multiloop control systems, several iterations are usually required for better control performances. Especially when pairings are undesirable, the autotuning sequences should be repeated with correct pairings, which result in long field experiments. Here, to avoid this drawback, a simple method to identify process models while loops are being sequentially tuned is proposed. The identified models can be used to correct pairings of multiloop control systems and to improve tuning performances without several field iterations. In addition, they can be used to obtain model-based control systems such as decoupling control systems.     

Effect of solution properties on nanofibrous structure of electrospun poly(lactic‐co‐glycolic acid)

Electrospinning of poly(lactic‐co‐glycolic acid) (PLGA) in chloroform or 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) was investigated, focusing on its solution parameters, to develop nonwoven biodegradable nanofibrous structures for tissue engineering. PLGA nanofibers were obtained by electrospinning of 15 wt % PLGA solution and the resulting average fiber diameters were varied with the range of 270–760 nm, depending on solution property. When small amounts of benzyl triethylammonium chloride (BTEAC) was added to the PLGA/chloroform solution, the average diameter was decreased from 760 to 450 nm and the fibers were densely amounted in a straight shape. In addition, the average fiber diameter (270 nm) of nanofibers electrospun from polar HFIP solvent was much smaller than that (760 nm) of nanofibers electrospun from nonpolar chloroform solvent. Therefore, it could be concluded that conductivity or dielectric constant of the PLGA solution was a major parameter affecting the morphology and diameter of the electrospun PLGA fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1214–1221, 2006     

Microstructure and morphology of amine-cured epoxy coatings before and after outdoor exposures—An AFM study

Atomic force microscopy (AFM) has been used to study the morphology and microstructure of an amine-cured epoxy before and after outdoor exposure. Measurements were made from samples prepared in an essentially CO₂-free, H₂O-free glove box and from samples prepared in ambient conditions. For those prepared in a CO₂-free glove box, AFM imaging was conducted on (1) an unexposed air/coating surface, (2) an unexposed coating bulk, (3) an unexposed coating/substrate interface, and (4) a field exposed air/coating surface. For samples prepared in ambient conditions, only the unexposed air/coating surface was investigated. The same regions of the exposed samples were scanned periodically by the AFM to monitor changes in the surface morphology of the coating as UV exposure progressed. Small angle neutron scattering and Fourier transform infrared spectroscopy (FTIR) studies were performed to verify the microstructure and to follow chemical changes during outdoor exposure, respectively. The results have shown that amine blushing, which occurs only under ambient conditions, had a significant effect on the surface morphology and microstructure of the epoxy. The surface morphology of the samples prepared under CO₂-free, dry conditions was generally smooth and homogeneous. However, the interface and the bulk samples clearly revealed a two-phase structure consisting of bright nodular domains and dark interstitial regions, indicating an inhomogeneous microstructure. Such heterogeneous structure of the bulk was in good agreement with results obtained by small angle neutron scattering of unexposed samples and by AFM phase imaging of the degraded sample surface. The relationship between submicrometer physical changes and molecular chemical degradation is discussed. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004, in Chicago, IL.     

Kinetics of volume expansion during infusion of Ringer’s solution based on two volume model

In this work mathematical models were developed to represent the kinetics of volume changes of fluid spaces associated with infusion of Ringer’s solution. During infusion of Ringer’s solution, the human body is assumed to be characterized by the two-fluid space model which has second volume space in addition to the first volume so that fluid exchanges between these two spaces are possible. Various infusion types were tested to accommodate different medical situations. Volunteers were given Ringer’s solution and the changes in blood hemoglobin were detected. From the comparison with experimental data, the two-fluid space model was found to represent adequately the kinetics of human volume expansion during infusion of Ringer’s solution.     

Effects of Purified Persimmon Tannin and Tannic Acid on Survival and Reproduction of Bean Bug, Riptortus clavatus

We evaluated the effects of tannic acid and purified perrsimmon tannin on survival and reproduction of bean bugs, Riptortus clavatus.Feeding behavior of R. clavatus was also examined on sweet (cv. Fuyu) and astringent (cv. Chongdosi) persimmon fruits. Soluble tannin in sweet persimmon fruits decreased from 3% in early June to 0.5% in late September, but it increased from 2 to 8% during the same period in astringent persimmon fruits. More bugs visited sweet than astringent persimmon. Numbers of piercing/sucking spots were higher on sweet than on astringent persimmon. When fed 1 and 3% solutions of persimmon tannin, adult bugs ingested only 64.1 and 9.5% of the amount of water ingested by those offered the control (distilled water). Amounts of persimmon tannin ingested by the adult bugs were 6.5 and 2.8 times higher at 1 and 3% tannin solutions compared to a 0.1% solution. Persimmon tannin exerted negative effects on survival and reproduction of R. clavatus at higher concentrations (1 and 3% solutions). Feeding of R. clavatus adults decreased with increasing tannin concentrations. When results from both sexes were pooled, 50% mortality was achieved at 11 and 4 days after treatment with the 1 and 3% tannin solutions, respectively. Reproduction decreased with 1% tannin, and no eggs were produced with 3% tannin solution. Tannic acid was similar in its effects on R. clavatus. All nymphs died 14, 12, and 7 days after feeding on 0.1, 1, and 3% tannic acid, respectively. Adults were less sensitive than nymphs, and their survival was not affected by 0.1% tannic acid. However. 1 and 3% tannic acid solutions were fatal. Survivorship decreased to 50% at 11 and 6 days after supplying tannin solutions of 1 and 3% concentrations. Higher concentrations (1 and 3%) resulted in reduced reproduction, as was seen with persimmon tannin. Our data may explain why R. clavatus does not invade sweet persimmon orchards until late July, when concentrations of soluble tannin are low enough to allow them to feed.     

Surface crosslinking of high‐density polyethylene beads in a modified plasma reactor

High‐density polyethylene (HDPE) beads were successfully surface‐crosslinked in a modified plasma reactor. The modified plasma reactor treats large amounts of beads, which are uniformly surface‐crosslinked. In this study, effects of the gas pressure, radio‐frequency (RF) power, and the treatment time on the degree of surface crosslinking were systematically investigated. Degree of surface crosslinking was measured by solvent extraction method (boiling xylene method, BXM). The gel content of plasma‐treated HDPE increases from 0.0 to 1.05% within 10 min at 100 mTorr, 200 W. FTIR and DSC analyses show that the crosslinked layer after plasma treatment is limited only at HDPE surface without changing the bulk thermal property of HDPE. Through the analysis of FTIR, it was confirmed that main peaks corresponding to CH₂ bands were decreased and two peaks corresponding to CF₂ and CF₃ were observed after plasma surface modification. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2921–2929, 2002; DOI 10.1002/app.10295     

Thermal behavior and the determination of the polymer-polymer interaction parameter of polycarbonate and a thermotropic liquid crystalline polymer blends

Summary The surface modification of low-density polyethylene(PE) by liquid phase photograft polymerization with acrylic acid(AA), acrylamide(AM) and glycidyl methacrylate(GMA) was described. The grafting of AA and AM was proved and characterized by electron spectroscopy for chemical analysis(ESCA). It was found that fully hydrophilic surface can be obtained in very short irradiation time. With ESCA and attenuated total reflection infrared spectroscopy(ATR-IR), it can be confirmed that bifunctional monomer GMA was grafted onto the PE film surface. Through further reaction with GMA grafted film, heparin and protamine were immobilized onto the grafted film surface.     

Surface hydrolysis of filaments based on poly(trimethylene terephthalate) spun at high spinning speeds

The surface alkaline hydrolysis of fibers made from poly(trimethylene terephthalate) (PTT) was studied after extruding the polymer at high spinning speeds from 2000 to 6000 m/min and heat setting in the range of temperatures from 100 to 180°C. Fiber weight loss increased with an increasing heat‐setting temperature but it was also dependent on the spinning speed. Some of the partially hydrolyzed fibers had a well‐developed, hydrophilic surface, and pore size in the range of 0.69 to 1.20 μm. The optimum reaction and morphological conditions for increasing porosity in PTT fibers depends on spinning speed and heat‐setting temperature. A temperature of 180°C is the upper limit for heat‐setting PTT filaments but seems to be the most effective for making porous fibers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1724–1730, 2004     

Time-slide window join over data streams

The join is an important operator in processing data streams. To produce outputs continuously over unbounded data streams, sliding windows are generally used to limit the scope of the join at a certain time. In the existing join algorithms, only a simple type of windows have been considered, which are updated whenever a new data item arrives on any input stream. On the other hand, a more common type of windows have not been addressed yet, whose intervals are updated periodically, i.e., slid by a predefined time interval. In this paper, we consider the time-slide windows in joining multiple data streams. The algorithm for the time-slide window join can vary according to (i) how frequently the join is evaluated and (ii) which structure is used for windowing. Regarding this, possible algorithms are discussed, and experimental results that compare their performances are provided in this paper.     

Statistical properties of interparticle/void distance for amorphous plastics toughening

Statistical properties of interparticle/void distance (ID) for various particle/void and dispersion types are studied in relation with toughening of plastics using computer‐generated three‐dimensional models. Particle/void size groups adopted were either of constant diameter or of log‐normal distribution. Particles/voids were dispersed at uniform‐random or flocculated with multiple clusters. It was found that IDs are (a) of approximately Gaussian distribution for particles/voids of either a constant diameter or a log‐normal distribution, when they are dispersed at uniform‐random, but (b) not of Gaussian distribution for particle/void sizes of bimodal log‐normal distribution, nor for flocculated log‐normal distribution of particles/voids dispersed with multiple clusters. It was also found that the degree of ID uniformity for a single group of log‐normally sized particles/voids is not sensitive to standard deviation of particle/void size. Mixing effect on ID properties using two groups of log‐normally distributed particles/voids with similar mean particle/void diameters was simulated. It was found that, when a significant amount (36 vol %) of particles/voids of a small mean and standard deviation of ID was mixed with a group of particles/voids of a large mean and standard deviation of ID, mean and standard deviation of ID for the mixture were not substantially lower than those of the group of particles/voids of the large mean and standard deviation of ID. It was also found that the degree of ID uniformity for the mixture of the two groups was lower than those of individual groups, indicating that the mixing has deleterious effect on toughening. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4256–4262, 2006