弯曲受力时中空管以及混凝土填充纤维复合管的有限元模型:部分填充优化和杆设计方法

非线性有限元模型的拓展与验证在相关的论文(Son J,Fam A.中空管以及混凝土填充纤维复合管的有限元模型:第一部分——抗弯模型拓展与验证)中已被用于研究部分填充混凝土纤维增强复合材料线杆的抗弯性能。为提高抗弯强度和稳定性,建议采用部分填充厚壁管来降低造价。对不同直径与厚度比以及不同分层结构的悬臂单杆进行混凝土部分填充长度优化。研究发现,当下列任意一种情况出现时,优化长度会减少:当直径与厚度比变小时;当纤维角度相对于弯曲管纵向轴夹角增加时;当弯曲管中纵向纤维减少时;当采用侧向分布荷载代替端部集中荷载时。建立了计算中空管和混凝土填充FRP管承载力矩的简单表达式,基于同时发生在中空管和混凝土填充管处的破坏,结合简单的设计方法体系来优化混凝土填充管的长度。同时提出了计算锥形线杆的程序。     

Stomata‐Inspired Photomechanical Ion Nanochannels Modified by Azobenzene Composites

A low‐powered and highly selective photomechanical sensor system mimicking stomata in the epidermis of leaves harvested from nature is demonstrated. This device uses a light‐responsive composite consisting of 4‐amino‐1,1′‐azobenzene‐3,4′‐disulfonic acid monosodium salt (AZO) and poly(diallyldimethylammonium chloride) (PDDA) coated on a membrane with tens of nanometer‐size pores. The ionic current change through the pore channels as a function of pore size variation is then measured. The tran–cis isomerism of AZO–PDDA during light irradiation and the operation mechanism of photomechanical ion channel sensor are discussed and analyzed using UV–vis spectroscopy and atomic force microscopy analysis. It presents the discriminative current levels to the different light wavelengths. The response time of the photoreceptor is about 0.2 s and it consumes very low operating power (≈15 nW) at 0.1 V bias. In addition, it is found that the change of the pore diameter during the light irradiation is due to the photomechanical effect, which is capable of distinguishing light intensity and wavelength.     

Temperature Control of a Regasification System for LNG-fuelled Marine Engines Using Nonlinear Control Techniques

International Journal of Control, Automation and Systems - This paper presents two nonlinear PID (NPID) controllers which control the glycol temperature of a regasification system for LNG-fuelled...     

Resistive switching characteristics and conducting nanobits of polycrystalline NiO thin films

Thin films of NiO were deposited on Pt/Ta/glass sub-strates using a radio frequency (RF) sputtering method. The NiO thin films showed polycrystalline nature, indicating preferentially (111)-oriented structure. The resistive random access memory (RRAM) capacitor of a Pt/NiO/Pt structure exhibited unipolar switching characteristics and bistable resistivities for 200 repeated switching cycles. Furthermore, RRAM nanobits array was formed on the NiO thin films by applying a bias. The RRAM nanobits had a diameter of approximately 8 nm and were observed via a conducting atomic force microscope (CAFM). The density of the RRAM nanobits array was estimated to be approximately 0.64 Tbit/cm².     

Conductive adhesive with transient liquid‐phase sintering technology for high‐power device applications

A highly reliable conductive adhesive obtained by transient liquid‐phase sintering (TLPS) technologies is studied for use in high‐power device packaging. TLPS involves the low‐temperature reaction of a low‐melting metal or alloy with a high‐melting metal or alloy to form a reacted metal matrix. For a TLPS material (consisting of Ag‐coated Cu, a Sn96.5‐Ag3.0‐Cu0.5 solder, and a volatile fluxing resin) used herein, the melting temperature of the metal matrix exceeds the bonding temperature. After bonding of the TLPS material, a unique melting peak of TLPS is observed at 356 °C, consistent with the transient behavior of Ag₃Sn + Cu₆Sn₅ → liquid + Cu₃Sn reported by the National Institute of Standards and Technology. The TLPS material shows superior thermal conductivity as compared with other commercially available Ag pastes under the same specimen preparation conditions. In conclusion, the TLPS material can be a promising candidate for a highly reliable conductive adhesive in power device packaging because remelting of the SAC305 solder, which is widely used in conventional power modules, is not observed.     

Combined Application of Antibrowning,Heat Treatment and Modified‐Atmosphere Packaging to Extend the Shelf Life of Fresh‐Cut Lotus Root

This work aimed to determine the effects of different concentrations of antibrowning treatments (that is, distilled water [DW], 1% ascorbic acid [AA], 0.5% chamomile [CM], and 1% AA + 0.5% CM) and heat‐treatment (55 °C for 45 s) combined with packaging under 4 different modified‐atmosphere gas compositions (that is, air, vacuum, 100% CO₂, 50% CO₂/50% N₂) on the quality and microbiological characteristics of fresh‐cut lotus root. The quality characteristics (that is, color, weight loss, texture, pH, polyphenoloxidase activity, and total phenolic content) of the AA + CM‐dipped sample in 100% CO₂ packaging were maintained significantly better than those of the other samples (P < 0.05). The microbiological counts observed in the DW‐dipped sample during storage were higher than those of the AA, CM, and AA + CM samples, and heat‐treatment retarded the microbiological deterioration of fresh‐cut lotus root. Therefore, the results revealed that dipping in an antibrowning treatment (AA + CM), and 100% CO₂ MAP with heat treatment effectively extend the shelf life of fresh‐cut lotus root to 21 d at 5 °C.     

Acute aortic outflow obstruction by diminution of bulboventricular foramen size after volume unloading in univentricular physiology

A young child with [S, L, L] segmental anatomy, double-inlet left ventricle, transposition of the great arteries, rudimentary right ventricle, and mildly restrictive bulboventricular foramen is reported, in whom intraoperative temporary snaring of the modified Blalock-Taussig shunt resulted in instantaneous and dramatic volume contraction of the left ventricle, decrease in bulboventricular foramen size, and increase of the gradient across the latter from 10 mm Hg preoperatively to 50 mm Hg. A modified Damus-Stansel-Kaye procedure using autogenous aortic tissue resulted in unobstructed aortic outflow; in addition, a bidirectional cavopulmonary shunt was performed. The importance of early relief of actual or potential aortic outflow obstruction in hearts with restrictive bulboventricular foramen is emphasized.     

Hydrogen production in fluidized bed by chemical-looping cycle

To investigate the feasibility of a chemical-looping hydrogen generation system, we investigated the reduction and water splitting reaction characteristics for three mediators and two reducing gas in a bubbling fluidized bed reactor (0.02 m I.D.). For three oxygen carrier particles (NiO/bentonite, Fe₂O₃/bentonite, (NiO:Fe₂O₃)/bentonite), hydrogen was used as a reduction gas and water was used as an oxidation gas. For (NiO: Fe₂O₃)/bentonite particle, carbon monoxide, which is the main component in the syngas from coal or heavy residue, was used as a reducing gas to check reactivity for the carbon containing fuels and carbon deposition characteristics. Based on the reactivity tests, (NiO: Fe₂O₃)/bentonite particle was selected as the best mediator for the chemical-looping hydrogen generation system to achieve stable continuous operation. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Application of solid phase-microextraction (SPME) and electronic nose techniques to differentiate volatiles of sesame oils prepared with diverse roasting conditions

Headspace volatiles of sesame oil (SO) from sesame seeds roasted at 9 different conditions were analyzed by a combination of solid phase microextraction (SPME)-gas chromatography/mass spectrometry (GC/MS), electronic nose/metal oxide sensors (MOS), and electronic nose/MS. As roasting temperature increased from 213 to 247 °C, total headspace volatiles and pyrazines increased significantly (P < 0.05). Pyrazines were major volatiles in SO and furans, thiazoles, aldehydes, and alcohols were also detected. Roasting temperature was more discrimination factor than roasting time for the volatiles in SO through the principal component analysis (PCA) of SPME-GC/MS, electronic nose/MOS, and electronic nose/MS. Electronic nose/MS showed that ion fragment 52, 76, 53, and 51 amu played important roles in discriminating volatiles in SO from roasted sesame seeds, which are the major ion fragments from pyrazines, furans, and furfurals. SO roasted at 213, 230, and 247 °C were clearly differentiated from each other on the base of volatile distribution by SPME-GC/MS, electronic nose/MOS, and electronic nose/MS analyses. Practical Application: The results of this study are ready to apply for the discriminating samples using a combinational analysis of volatiles. Not only vegetable oils prepared from roasting process but also any food sample possessing volatiles could be targets for the SPME-GC/MS and electronic nose assays. Contents and types of pyrazines in sesame seed oil could be used as markers to track down the degree of roasting and oxidation during oil preparation.