The high-temperature oxidation of Ni-20%Cr alloys containing various oxide dispersions

The oxidation behavior of Ni-20%Cr alloys containing approximately 3 vol.% Y₂O₃, ThO₂, and A1₂O₃ as dispersed particles has been examined in the temperature range 900 to 1200° C in slowly flowing oxygen at 100 Torr. The results show that the oxidation behavior of the Y₂O₃-, ThO₂-, Al₂O₃-, and Ce0₂-containing alloys is very similar and that some anomalies in the behavior of the ThO₂-containing alloy might be explained by the slower rate of chromium diffusion in this coarse-grained alloy. Two Al₂O₃-containing alloys were studied. One with a relatively coarse dispersoid size behaved in a manner analogous to a dispersion-free Ni-30% Cr alloy at 1100°C. The other alloy contained a dispersion of fine Al₂O₃ particles and behaved exactly like the Y₂O₃-containing alloy at 1000 and 1100°C, but at 1200° C oxidized at a faster rate. It has been shown that the adherent scales on dispersion-containing alloys have a stabilized fine grain size, whereas the nonadherent scales on dispersion-free alloys undergo grain growth.This work has been supported by the Naval Air Systems Command under Contract No. N00019-72-C-0190.     

High-Temperature Oxidation Behavior of ODS–Fe3Al

The high-temperature oxidation behavior of an oxide dispersion-strengthened (ODS) Fe₃Al alloy has been studied during isothermal and cyclic exposures in oxygen and air over the temperature range 1000 to 1300°C. Compared to commercially available ODS–FeCrAl alloys, it exhibited very similar short-term rates of oxidation at 1000 and 1100°C, but at higher temperatures the oxidation rate increased because of increased scale spallation. Over the entire temperature range, the oxide scale formed was -Al₂O₃, with the morphological features typical of reactive-element doping and was similar to those formed on the ODS–FeCrAl alloys. Although initially this scale appeared to be extremely adherent to the Fe₃Al substrate, an undulating metal–oxide interface formed with increasing time and temperature, which led to cracking of the scale in the vicinity of surface undulations accompanied by a loss of small fragments of the full-scale thickness. In some instances, the surface undulations appeared to have resulted from gross outward local extrusion of the alloy substrate. Similar features developd on the FeCrAl alloys, but they were typically much smaller after a given oxidation exposure. The ODS–Fe₃Al alloy has a significantly larger coefficient of thermal expansion (CTE) than typical FeCrAl alloys (approximately 1.5 times at 900°C) and this appears to be the major reason for the greater tendency for scale spallation. The stress generated by the CTE mismatch was apparently sufficient to lead to buckling and limited loss of scale at temperatures up to 1100°C, with an increasing amount of substrate deformation at 1200°C and above. This deformation led to increased scale spallation by producing an out-of-plane stress distribution, resulting in cracking or shearing of the oxide.     

Forging preform design with shape complexity control in simulating backward deformation

This paper presents a preform design method which employs an alternative boundary node release criterion in the finite element simulation of backward deformation of forging processes. The method makes use of the shape complexity factor which provides an effective measure of forging difficulty. The objective is to release die contacting nodes in a sequence which will minimize the geometric complexity throughout the backward deformation simulation. This is done by calculating the effect of releasing each of a select group of boundary element nodes at each finite element solution step. The particular detached node which results in the minimum shape complexity factor will be released for the current step. This process continues for each backward step until the last few nodes remain in contact. This design method is demonstrated through the simulated forging of an integrated blade and rotor turbine disk blank. A preform shape developed by this method is compared with an empirically designed preform. Performance parameters for comparison include die fill, flash volume, effective strain variance, frictional power and die load. Comparing the results of the forward simulations indicates improved performance of the preform design using FEM based backward deformation method over that of the empirical design.     

Automated speech recognition for spreadsheet tasks: Performance effects for experts and novices

The performance of spreadsheet users was compared for two modes of input to the computer, keyboard and automated speech recognition (ASR). Subjects from both an expert group and a novice group were also classified by decision style. Dependent measures were task completion time, accuracy, keystroke count, correction count, and user confidence. Results for a speaker‐dependent, discrete‐word recognizer showed that, for both simple data input and more complex analytical spreadsheet tasks, neither the experts nor the novices performed more effectively using ASR. However, both groups expressed the desirability of having speech input as an option for desktop computing.     

'Tacitus' project: identifying multi-sensory perceptions in creative 3D practice for the development of a haptic computing system for applied artists

This paper outlines the major motivating factors concerning a novel collaborative project between Edinburgh College of Art and Edinburgh Virtual Environment Centre. The Tacitus project will investigate the use of multi-modal virtual environments, specifically, the haptic (touch) modality, with regards to the creative processes employed by designers working within the field of applied arts. The salient areas of research are described, and the methods by which information regarding these areas will be obtained are considered. Initial investigations have revealed a strong need to mimic the traditional applied artists' workspaces, with co-location of visual and haptic cues a priority.     

Reversible inactivation of purified leukocyte integrin CR3 (CD11b/CD18, alpha m beta 2) by removal of divalent cations from a cryptic site

Integrins exhibit reversible changes in their ability to bind ligands and these changes enable transient cell adhesion. We recently showed that leukocyte integrin CR3 (complement receptor type three, CD11b/CD18, alpha m beta 2) may be purified in a form that is either capable or incapable of binding soluble, monomeric ligand and that "inactive" CR3 may be rendered capable of binding ligand by addition of an anti-CR3 mAb known as KIM-127 (Cai and Wright, JBC. 270: 14358, 1995). Here, we demonstrate that active CR3 may be rendered inactive by treatment of immobilized receptor with EDTA. EDTA-treated CR3 failed to bind ligand even in the presence of mM Ca2+ and Mg2+, suggesting that EDTA-treatment caused a change in the receptor that is not readily reversed. EDTA-treated receptor did, however, bind ligand upon addition of KIM-127 plus Mg2+ with an affinity (17.8 +/- 4.5 nM) similar to untreated, active receptor (12.5 +/- 4.7 nM). EDTA-treated CR3 thus exhibits the properties of inactive CR3, in which the ligand binding site is cryptic but subject to exposure by KIM-127. A candidate for the cryptic ligand binding site is the I-domain, a Mg2+-binding region in the alpha chain of CR3. We found that monomeric C3bi binds directly to recombinant I-domain in a Mg(2+)-dependent fashion with an affinity of 300 +/- 113 nM. These results thus suggest that CR3 may be inactivated by removing tightly bound divalent cation from a cryptic site in CR3.     

In Situ Electrical Network Activation and Deactivation in Short Carbon Fiber Composites via 3D Printing

Prior studies on carbon-filler based, conductive polymer composites have mainly investigated how conductive filler morphology and concentration can tailor a material's electrical conductivity and overlooks the effects of filler alignment due to the difficulty to control and quickly quantify the filler alignment. Here, direct ink write 3D printing's unique ability is utilized to control carbon fiber alignment with a single process parameter, velocity ratio, to instantaneously activate or deactivate the electrical network in composites. Maximum electrical conductivity is achieved by randomly aligning carbon fibers that enhances the chance of direct fiber-to-fiber contact and, thus, activating the electrical network. However, aligning the fibers by increasing the velocity ratio disrupts the electrical network by minimizing fiber-to-fiber contact that resulted in a drastic decrease in electrical conductivity by as much as five orders of magnitude in both short and long carbon fiber composites. With this study, this study demonstrates that electrically conductive or insulative composites can be fabricated sequentially with a single ink. This novel ability to instantaneously control the electrical conductivity of carbon fiber reinforced composites allow to directly embed conductive pathways into designs to 3D print multifunctional composites that are capable of localized heating and self-sensing.     

The simple genetic algorithm and the Walsh transform: Part I, Theory

This paper is the first part of a two-part series. It proves a number of direct relationships between the Fourier transform and the simple genetic algorithm. (For a binary representation, the Walsh transform is the Fourier transform). The results are of a theoretical nature and are based on the analysis of mutation and crossover. The Fourier transform of the mixing matrix is shown to be sparse. An explicit formula is given for the spectrum of the differential of the mixing transformation. By using the Fourier representation and the fast Fourier transform, one generation of the infinite population simple genetic algorithm can be computed in time O(cllog2(3)), where c is arity of the alphabet and l is the string length. This is in contrast to the time of O(c3l) for the algorithm as represented in the standard basis. There are two orthogonal decompositions of population space that are invariant under mixing. The sequel to this paper will apply the basic theoretical results obtained here to inverse problems and asymptotic behavior.     

The simple genetic algorithm and the Walsh transform: Part II, The inverse

This paper continues the development, begun in Part I, of the relationship between the simple genetic algorithm and the Walsh transform. The mixing scheme (comprised of crossover and mutation) is essentially "triangularized" when expressed in terms of the Walsh basis. This leads to a formulation of the inverse of the expected next generation operator. The fixed points of the mixing scheme are also determined, and a formula is obtained giving the fixed point corresponding to any starting population. Geiringer's theorem follows from these results in the special case corresponding to zero mutation.     

The invisible profession

The job of a manager continues to be one of achieving outcomes through other people. However, in the current work environment, managers are finding that while their scope of responsibility is expanding, the traditional power base used to excourage high performance is shrinking. There are limited rewards a manager can use to gain commitment from their staff. Even if some of those rewards are available, many of the new employees do not see them as motivators. Employees come to the workplace with a different set of expectations. There seems to be a mismatch between the traditional management approach to getting the best from the worker and what the worker wants from their manager. In as much as the workplace and the worker are changing so too must manager's approach to "getting the job done."