基于西门子楼宇自控系统的中央空调计费系统

介绍了基于西门子楼宇自控系统的空调计费系统的软硬件设计和具体实现.该系统的特点是借助西门子S600系统强大的数据处理和控制能力,采用时间记录和能量测量相结合的方法进行计费,具有实时监测和定时输出报表功能.该系统计量准确、计费合理、安全可靠、性价比高,满足了现代物业管理的需要.     

宏蜂窝模型的传播模型校正研究

详细介绍了 宏蜂窝传播模 型校正的基本操作流程 结果分析及注意事项 对工程 ,人员了解和开展模型校正工作有一定的指导作用 。     

国内3G网络共享问题之研究

随着国内3G时代的来临，3G网络共享问题越来越受到人们的关注。本文结合国内移动通信的现状，着重分析了3G网络共享的模式及经济效益，论述了3G网络共享的相应策略。     

Analysis and comparison of two-dimensional permanent-magnet arrays for planar motor

This paper investigates three kinds of permanent-magnet arrays used in planar motors with polarity centers distributed in the lattices of a matrix. The magnetic field of every kind of magnet array is analyzed by analytical methods. First, we give a Laplace equation of magnetic scalar potential and a series of boundary conditions. Then, we derive the analytical expressions of magnet field strength and magnet flux density in the air gap of each kind of magnet array by the method of separation of variables. Finally, we compare the three types of magnet arrays on the basis of the analytical solutions.     

EPP在便携式数据采集系统中的应用

分析了并口处于EPP(增强型并行端口)模式时和单片机进行数据交换的原理.介绍了有关EPP的基本特性、信号定义、操作模式及其程序设计方法,设计了基于EPP协议的便携式数据采集系统,给出了技术解决方案,讨论了系统的硬件接口电路和软件编程.方案具有可靠性高、速度快、软硬件设计简捷等优点.     

碳纤维复合材料柔性连续抽油杆开发及应用

碳纤维柔性连续抽油杆选用高性能碳纤维 ,以环氧树脂胶液为基体材料 ,添加一定配比的固化剂、促进剂和脱模剂 ,采用拉挤成型工艺制成 ,其开发的关键技术是连续成型、连接接头和安全保险装置。现场应用试验表明 ,TXC— 1、TXC— 2、TXC— 3三种规格的碳纤维柔性连续抽油杆能可靠应用于泵挂深度分别为 12 0 0、 180 0、 30 0 0m的直井和斜井中 ,实测比钢抽油杆节电 ,日产油量提高 。节能增产效果显著。     

芳烃抽提装置技术改造

由于中国石化锦西石化分公司600kt／a连续重整装置的建设，芳烃抽提装置的原料由原来的脱戊烷油变为Ce组分。为此，对抽余油水洗塔和芳烃分离部分的苯塔塔盘，以及苯塔塔顶和塔底抽出部分进行了改造，更换部分机泵和增加变频泵，并将常规仪表改为DCS控制。改造后装置实现一次开车成功，生产出合格产品。抽余油中总芳烃含量小于0．1％，苯回收率达到99%以上。     

Monodispersed thermoresponsive hydrogel microspheres with a volume phase transition driven by hydrogen bonding

We report the synthesis and characterization of monodispersed thermoresponsive hydrogel microspheres with a volume phase transition driven by hydrogen bonding. The prepared microspheres, composed of poly(acrylamide-co-styrene) (poly(AAM-co-St)) cores and poly(acrylamide)/poly(acrylic acid) (PAAM/PAAC) based interpenetrating polymer network (IPN) shells, were featured with high monodispersity and positively thermoresponsive volume phase transition characteristics with tunable swelling kinetics, i.e. the particle swelling was induced by an increase rather than a decrease in temperature. The monodisperse poly(AAM-co-St) seeds were prepared by emulsifier-free emulsion polymerization, the PAAM or poly(acrylamide-co-butyl methacrylate) (poly(AAM-co-BMA)) shells were fabricated on the seeds by free radical polymerization, and the core-shell microspheres with PAAM/PAAC based IPN shells were finished by a method of sequential IPN synthesis. The microsphere size increased with increasing both AAM and BMA dosages. The increase of hydrophilic monomer AAM dosage resulted in a better monodispersity, but the increase of hydrophobic monomer BMA dosage led to a worse monodispersity. With increasing the crosslinker methylenebisacrylamide (MBA) dosage, the mean diameter of the microspheres decreased and the monodispersity became better. An equimolar composition of AAC and AAM in the IPN shells of the microspheres resulted in a more complete shrinkage for the microspheres at temperatures lower than the upper critical solution temperature. Both BMA and MBA additions depressed the swelling ratio of the hydrodynamic diameter of the microspheres.     

Level set and geodesic active contours based measurement of material removal between serial sections

The measurement of the thickness of material removed between serial sections is a crucial step of three-dimension reconstruction. Geodesic active contours is an efficient method for contour detection of objects on an image. The indents on the SiC/Al composite micrographs are segmented by using level set and geodesic active contours. After getting the contours of the indents, we calculate the distance from the uppermost pixel to the lowermost pixel to get the vertical diagonal length, and calculate the distance from the leftmost pixel to the rightmost pixel to get the horizontal diagonal length of each contour. Then the final length of each diagonal is acquired by averaging the vertical diagonal length and the horizontal diagonal length, respectively. The Vickers’ indenter is made by a square pyramidal-shaped diamond with opposite faces at an angle of 136°, so the thickness of material removed between two serial sections and the length difference of the diagonals on the two serial sections has a definite geometrical relation. Thus the thickness of material removed between two serial sections is acquired using the geometrical relation.     

Improving Cost Estimates of Construction Projects Using Phased Cost Factors

Central to cost-based competition is the capability to accurately predict the cost of delivering a project. Most literature on cost estimation focuses on specific estimation methods as generic techniques and little attention has been paid to the unique requirements at each project stage. This note attempts to identify the critical factors for effective estimation at various stages of typical construction projects. Drawing from organization control theory and cost estimating literature, this note develops a theoretical framework that identifies the critical factors for effective cost estimation during each project phase of a conventional construction project. The underlying logic is that as a cost estimating effort progresses, both task programmability and output measurability improve. As a result, control effort will shift from input-oriented control to a combination of output and behavior control.