In situ formation of multi scale reinforcing phases to improve performance of Al2O3-SiC C castables

In order to improve the physical properties and slag corrosion resistance of refractory materials for hot metal pretreatment, different contents of composite metal powders (CMP) were introduced into Al2O3-SiC-C refractory castables. The effect of CMP on the microstructure, physical properties and slag corrosion resistance of Al2O3-SiC-C refractory castables were studied. The results show that the multi scale reinforcing phases including flake crystals, rod shaped fibers, filamentous fibers and whiskers are in situ formed in the samples with addition of CMP, which result to the improvement of the cold modulus of rupture and cold crushing strength. When the addition of CMP is 6 wt.%, the high temperature modulus of rupture increases by 231%, the thermal shock resistance increases by 77% after thermal shock by water cooling 5 times and the percentage of the slag resistant area reduces by 37.2%.     

利用铝（100）面隧道孔制备纳米模板及有序阵列材料

高纯铝箔通常通过电化学扩面后用作铝电解电容器的阳极材料。利用铝箔（100）面隧道孔制备纳米模板。这种纳米模板的特点是制作简单、模板面积大，纳米阵列材料形状可控性强。还利用两步电化学侵蚀铝箔的特殊工艺，研制出纵横交错的TiO2纳米有序阵列材料。     

铁素体球墨铸铁与20钢的闪光对焊

试验使用铁素体球墨铸铁和20钢的实心棒料进行了闪光对焊，通过改变次级电压4～8级，通电时间3～5s，观察其焊接接头组织的变化并测定其抗拉强度。结果表明，接头由三个区组成；当通电时间一定时，抗拉强度随次级电压的升高先减小后增大；当次级电压一定时，抗拉强度随通电时间的增加而增大。在次级电压为8级、通电时间为5s时，抗拉强度达最大值，为370．8MPa，是20钢母材的90.4％，是球墨铸铁母材的83.7％。     

靶向抗癌药格列卫与其治疗白血病疗效监测

Gleevec是抑制致癌的融合蛋白BCR-ABL的一种分子靶向治疗药物,BCR-ABL是一种与慢性髓细胞性白血病(CML)有关的酪氨酸激酶抑制剂。用Gleevec选择性地抑制BCR-ABL活性在治疗CML中显示出很好的效果,特别是在CML慢性期,因此,监测疗效非常重要。现就Gleevec的研究进展及如何监测其在CML中的疗效作一简单综述。     

汽轮机叶片用X20Cr13钢的热处理工艺研究

采用正交试验对汽轮机叶片用X20Cr13钢进行了热处理工艺研究，以获得该钢的最佳热处理工艺，并在回火后以不同的速度冷却，以揭示冷却速度对钢的回火脆性的影响。结果，X20Cr13钢的最佳热处理工艺为900℃油淬或风冷，670℃回火，风冷。     

Realization of Tapered Waveguide by Stretching the Rod Waveguide

By stretching the rod waveguide with different velocities in opposite directions, the tapered waveguide can be fabricated. In condition of taking no account of volume expansion caused by heating and under the assumptions of volume conservation,the rod waveguide can be stretched freely in the heated region without being stretched outside of the heated region. A model,which shows the relation of the transition shape and the two factors, that is the ratio of two velocity and the heated region length, is presented for the shape of the taper transition through mathematic deduction. Based on this model, a desired tapered waveguide can be fabricated. The tapered waveguide are widely used for fabricating tapered fiber couplers and sensors. In addition, the conclusion can be used for fabricating fused fiber coupler.     

一种基于bit位的运动补偿方法

本文讨论了等离子体显示屏所特有的在显示运动画面时出现的伪轮廓线现象，对产生的原因进行了分析并给出了软件模拟的结果。在此基础上，提出了一种基于bit位的运动补偿方法来改善运动图像的画面质量，同时根据人眼的视觉特征对补偿方法做了进一步的优化。最后对基于bit位的运动补偿方法进行了比较和验证，结果表明基于bit位的运动补偿方法可以基本消除运动画面的伪轮廓线现象。     

Analysis and Simulation of S-shaped Waveguide in Silicon-on-insulator

The simulation and analysis of S-shaped waveguide bend are presented.Bend radius larger than 30 mm assures less than 0.5 dB radiation loss for a 4-μm-wide silicon-on-insulator waveguide bend with 2-μm etch depth.Intersection angle greater than 20° provides negligible crosstalk (<-30 dB) and very low insertion loss.Any reduction in bend radius and intersection angle is at the cost of the degradation of characteristics of bent waveguide and intersecting waveguide, respectively.     

帧中继交换技术

本文论述了帧中继交换的概念、标准，结构、特点网络式样及在互连网中的应用。     

泥沙起动条件及机理的非线性研究

 分析了单颗粒、均匀沙及非均匀沙的起动现象及其机理，认为泥沙的起动属于突变论研究的范畴。从泥沙起动所遵循起动条件的力学规律出发，导出泥沙起动条件方程。在此基础上，利用尖点突变性质对各种泥沙起动现象及机理进行了描述和说明。