Reply to comments on “Error rate performance of theprojection code”

The authors reply to the comments by Koppelaar and Tolhuizen (see ibid. vol.46, no.9, p.573, 1998). They state that the optimum choice of the slopes used to perform the encoding process in a projection code always results in maximizing the minimum Hamming distance so that d=2 ^r     

Two-level optimal output feedback stabilizer design

The paper addresses the design of two-level power system stabilizers using an optimal reduced order model whose state variables are torque angles and speeds. The reduced order model retains their physical meaning and is used to design a two-level linear feedback controller that takes into account the realities and constraints of electrical power systems. The two-level control strategy is used, and a global control signal is generated from the output variables to minimize the effect of interactions. The effectiveness of this controller is evaluated and a multimachine system is given as an example to illustrate the advantages of the proposed method. Responses of the system with a two-level scheme and an optimal reduced order scheme are included for comparative analysis.     

利用短周期地脉动推断深层地基S波速度

从二维随机波场的相关理论出发，提出了如何从短周期地脉动（频率＞０．５Ｈｚ）时域信号中计算Ｒａｙｌｅｉｇｈ波弥散曲线，进而反演深层地基剪切波（Ｓ波）速度的理论方法和分析技术，并结合实测信号的分析结果，探讨了该方法的可行性和实用性。     

The investigation of 32P wire for catheter-based endovascular irradiation

The dose distribution from a 32P source has been measured and calculated in order to evaluate its application in endovascular irradiation. The source dimension was 27 mm in length and 0.3 mm in diameter and was embedded in the end of a Ni-Ti wire. Dose measurements were performed using radiochromic film in several specially designed tissue equivalent phantoms. Loevinger's point dose kernel was used for the calculation. The approximate dose rate at a radial distance of 1.5 mm from the center of the source was found to be 6.75 cGy/s per GBq (0.25 cGy/s per mCi), which allows the delivery of a therapeutic dose in a short time interval with a satisfactory homogeneity without stepping the source. However, the dose rate falls off almost exponentially along the radial distance. Therefore it may not be suitable for treating large diameter vessel from a centrally located source. The effect of a curved 32P wire source on the radial dose distribution was also investigated. The results showed that for a maximum bend of 180 degrees the dose rate was increased by as much as 20% along the inner radial distance but decreased by as much as 20% along the outer radial distance compared to the dose along a straight wire. However, for curvatures normally encountered in a clinical situation, the dose rate was changed less than 5%.     

变速铣削的试验研究

通过试验考证了变速铣削的减振效果和机床电机电流的波动幅度，试验结果表明，变速铣削同样具有明显的减振效果。机床电机电流虽有波动，但波动幅度不大，不会影响电机的正常使用，变速铣削具有良好的应用前景。     

钢的连铸用保护渣的表征

在钢的连铸过程中,结晶器保护渣的性质强烈地影响着铸造的行为、钢的质量、以及连铸工艺的环境.本研究采用高温显微技术来研究保护渣的熔化行为,采用液滴测试方法来测定保护渣的熔化速率.结果表明:自由碳是控制保护渣熔化行为的主要因素.熔化速率随碳的反应能力的增加而增加,随着碳含量的减少而增加.     

高合金铁基烧结材料在轧钢导位中的应用研究

本文研究了高合金铁基烧结材料在轧钢导位中的应用。实验表明,通过粉末冶金液相烧结技术,可以获得具有优良综合性能的制品,材料密度ρ≥7.5 g/cm3,硬度≥55 HRC,抗弯强度≥1 000 MPa,冲击韧度αk≥3.9 J/cm2,满足了轧钢导位辊的工作要求。材料利用率可达95%以上、降低了制备成本。使用寿命是普通轧辊寿命的3~6倍,适用于线材和小型型材的轧钢生产。