Associative properties of perfluorooctyl end‐functionalized polystyrene–poly(ethylene oxide) diblock copolymers

The synthesis of 2,2,3,3‐tetrahydro‐perfluoroundecanoyl end‐functionalized polystyrene–poly(ethylene oxide) block (PS‐block‐PEO‐R_F) copolymers and their matching PS‐block‐PEO diblock copolymers was carried out by sequential anionic polymerization. Viscometry and ¹⁹F NMR studies show that the PS‐block‐PEO copolymers, in contrast to their matching PS‐block‐PEO‐R_F copolymers, exhibit a micellar rather than the associative behavior seen for the latter. However, the presence of an excess of fluorinated acid, used for end‐functionalization, produces a reduction of the associative behavior above the overlap concentration, with the fluorinated acid acting like a surfactant. A competition may also occur between PS—and R_F—mediated micellization. Copyright © 2004 Society of Chemical Industry     

Methacryloxyethyl phosphate‐grafted expanded polytetrafluoroethylene membranes for biomedical applications

Expanded polytetrafluoroethylene (ePTFE) membranes were modified by graft copolymerization with methacryloxyethyl phosphate (MOEP) in methanol and 2‐butanone (methyl ethyl ketone (MEK)) at ambient temperature using gamma irradiation. The effect of dose rate (0.46 and 4.6 kGy h^?1), monomer concentration (1–40 %) and solvent were studied and the modified membranes were characterized by weight increase, X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XPS was used to determine the % degree of surface coverage using the C? F (ePTFE membrane) and the C? C (MOEP graft copolymer) peaks. Grafting yield, as well as surface coverage, were found to increase with increasing monomer concentration and were significantly higher for samples grafted in MEK than in methanol solution. SEM images showed distinctly different surface morphologies for the membranes grafted in methanol (smooth) and MEK (globular), hence indicating phase separation of the homopolymer in MEK. We propose that in our system, the non‐solvent properties of MEK for the homopolymer play a more important role than solvent chain transfer reactions in determining grafting outcomes. Copyright © 2005 Society of Chemical Industry     

Trenched‐Sinker LDMOSFET (TS‐LDMOS) Structure for 2 GHz Power Amplifiers

This paper proposes a new LDMOSFET structure with a trenched sinker for high‐power RF amplifiers. Using a low‐temperature, deep‐trench technology, we succeeded in drastically shrinking the sinker area to one‐third the size of the conventional diffusion‐type structure. The RF performance of the proposed device with a channel width of 5 mm showed a small signal gain of 16.5 dB and a maximum peak power of 32 dBm with a power‐added efficiency of 25% at 2 GHz. Furthermore, the trench sinker, which was applied to the guard ring to suppress coupling between inductors, showed an excellent blocking performance below ?40 dB at a frequency of up to 20 GHz. These results confirm that the proposed trenched sinker should be an effective technology both as a compact sinker for RF power devices and as a guard ring against coupling.     

Positively Thermo‐Sensitive Monodisperse Core–Shell Microspheres

In this paper, we report on a novel family of monodisperse thermo‐sensitive core–shell hydrogel microspheres that is featured with high monodispersity and positively thermo‐responsive volume phase transition characteristics with tunable swelling kinetics, i.e., the particle swelling is induced by an increase rather than a decrease in temperature. The microspheres were fabricated in a three‐step process. In the first step, monodisperse poly(acrylamide‐co‐styrene) seeds were prepared by emulsifier‐free emulsion polymerization. In the second step, poly(acrylamide) or poly[acrylamide‐co‐(butyl methacrylate)] shells were fabricated on the microsphere seeds by free radical polymerization. In the third step, the core–shell microspheres with poly‐ (acrylamide)/poly(acrylic acid) based interpenetrating polymer network (IPN) shells were finished by a method of sequential IPN synthesis. The proposed monodisperse core–shell microspheres provide a new mode of the phase transition behavior for thermo‐sensitive “smart” or “intelligent” monodisperse micro‐actuators that is highly attractive for targeting drug delivery systems, chemical separations, sensors, and so on.     

High‐Performance,Monolithic Polyaniline Electrochemical Actuators

New polyaniline (PANI) asymmetric membranes were fabricated using a phase‐inversion technique with hexane as the coagulation bath. These membranes exhibit a dense structure with macrovoids distributed asymmetrically throughout the cross‐section. A stress–strain study demonstrated that the Young's modulus (1.421 GPa) and strain at break (7.6 %) of the new PANI asymmetric membranes prepared from hexane are approximately 12 and 4 times higher, respectively, than the values reported previously for the PANI integrally skinned asymmetric membranes (ISAMs) (123 MPa Young's modulus and 1.8 % strain at break). Furthermore, monolithic electrochemical actuators based on a single PANI asymmetric membrane were constructed, and a bending movement of up to 20 Hz was experimentally recorded in a hydrochloric acid aqueous solution. A lifetime of over 329 500 cycles was determined for these actuators at a ± 2° angular displacement (5 Hz). The lifetime is limited by a bending fatigue that creates a transversal crack on the PANI membrane at the air–water interface. Control over the actuator movement is also manifested by the linear dependences of the bending angle on the charge and of the angular velocity on the current. These relationships are independent of both the kind of applied electric signal and the frequency used.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Use of Explosives on The Moon

The utilization of explosives for excavation on the lunar surface is under serious consideration as a part of the design for construction of temporary and permanent bases. An excavation research program has shown that small‐scale explosives blasting in a lunar‐soil simulant will greatly reduce the digging forces required for scoop and dragline excavators. Some crater‐blasting parameters were determined for the lunar soil simulant at one Earth gravity and at 10 Earth gravities using a centrifuge. The size of the craters produced at 10 Earth gs matched those formed at one earth g by scaling according to the weight of the explosive. These data can be applied to explosive‐excavation problems such as habitat construction, burial of nuclear power sources, and the rapid construction of shelters remote from the main base to shield against solar‐flare activity.     

Production and properties of micro‐porous glas bubble zinc and aluminium composites

Micro‐porous syntactic foams were produced by means of integration of glass bubbles into aluminium and zinc matrices. Preforms of glass bubbles were pressure infiltrated with the alloys AlSi9Cu9 ans ZnAl4Cu using squeeze casting. The preforms were sintered thermically without the use of bonding agents. Using the combination of different sintering steps syntactic foams with locally different densities could be produced. The mechanical properties of the foams were tested indicating a high compression strength of the foams and a very good compression energy absorption. Furthermore, corrosion behaviour and behaviour at higher temperatures were investigated.     

From information to probability: An axiomatic approach—Inference is information processing

We define the very rich language of composed conditionals on a three‐valued logic and use this language as the communication tool between man and machine. Communication takes place for three reasons: knowledge acquisition, query, and response. Learning, thinking, and answering questions are of a pure information theoretical nature. The pivot of this knowledge processing concept is the amount of information (bit) we receive if a conditional becomes true. We follow an axiomatic approach to information theory rather than the classical probabilistic approach of Shannon; information comes first, and then comes probability. In the light of this philosophy, query and response experience new interpretations. Both, acquisition and response are realized by maximizing entropy and minimizing relative entropy, respectively. The iterative solution of these mathematical optimization problems gives new insights into the adaptation of prior knowledge to new information. Our expert system shell SPIRIT supports this kind of knowledge processing, which will be established by suitable examples. © 2003 Wiley Periodicals, Inc.