A reliable and manufacturable method to induce a stress of >1 GPa on a P-channel MOSFET in high volume manufacturing

This letter discusses a reliable and manufacturable integration technique to induce greater than 1 GPa of stress into a p-channel MOSFET, which will be required to increase the drive current beyond 1 mA//spl mu/m at the sub-90-nm process generation. Uniaxial compressive stress is introduced into the p-channel by both a selective deposition of SiGe in the source/drain and an engineered 2.5-GPa compressively stressed nitride. The highest to date compressively stressed SiN film is obtained by heavy ion bombardment during the deposition of the film.     

Insulating safety analysis of the hot-line sweeping robot

This paper presents a method of calculating the insulating safety distances for hot-line working robots at high voltage when dielectric is adulterated with conducts. Also, finite element method is adopted to calculate the electric field strength to find whether it is beyond the critical. The above methods have been applied to analyze the insulating safety of the robot for hot-line sweeping post insulators in a 220 KV substation. They have also been testified by experimentations.     

轻便、操作方便自适应控制的MIG焊机——MinarcMig^TM

Kemppi公司的新型MinarcMig^TM自适应逆变器是重量很轻、功能强大、使用方便的焊机。     

油田热采注汽管道在线检测技术现状

稠油热采注汽管道由于长期在高温、高压下运行,极易发生各种损伤,如腐蚀、裂纹、材料退化等,极易造成管道承压能力降低,发生失效事故。如何检测出潜在危险性缺陷,判断注汽管道能否继续使用,是保证注汽管道安全运行的关键问题。探讨了高温压力管道在线检测技术发展现状及其应用范围。     

600MW机组热力系统优化设计探讨

在保证机组运行安全、可靠的前提下，对热力系统进行了优化，合理地减少了备用设备和备用容量，降低系统阻力及工质损失。从而达到了降低能耗和初投资，减少运行成本的目的。     

En/Decoder for Spectral Phase-Coded OCDMA System Based on Amplitude Sampled FBG

A novel en/decoder for spectral phase-coded optical code-division multiple-access system based on amplitude sampled fiber Bragg grating (FBG) is proposed. Both equivalent chirp and equivalent phase shift are achieved by amplitude sampling. Compared with previous en/decoder based on step chirped FBG, it is easier to fabricate. The performance of the proposed en/decoder is verified by both numerical simulation and experimental demonstration.     

Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

Kinetics study of Ti[O(CH2)4OCHCH2]4 initiated ring‐opening polymerization of ε‐caprolactone by differential scanning calorimetry

Chemical shrinkage was used for the in situ measurement of the progressing chemical stabilization reactions and the influence of ozone during the stabilization of polyacrylonitrile. A method for evaluating the activation energy through the sensitivity temperature is presented. The calculated results show that the activation energies were 161.57 kJ/mol in air and 181.23 kJ/mol in ozone-enriched air. Therefore, the chemical reactions were postponed during stabilization in ozone-enriched air. Ozone seemed to act in three ways: first, ozone promoted the formation of the serious skin–core structure. Second, ozone accelerated the chemical reactions and shortened the stabilization time at lower heating rates. Third, ozone postponed the chemical reactions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Synthesis,characterization, and redox and electrochromic behaviors of poly(3-n-octyloxythiophene)

Poly(3-n-octyloxythiophene), a conjugated polymer, which possessed solubility in common organic solvents, was synthesized by electrochemical polymerization in the presence of lithium perchlorate as the supporting electrolyte and sodium dodecyl sulfate as the surfactant in an aqueous medium. Characterizations of the intermediate, monomer, and polymer were performed by NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet–visible spectroscopy, and gel permeation chromatography. The process of electrochemical polymerization and the electrochemical redox behaviors were investigated by cyclic voltammetry and the potentiostatic method. A poly(3-n-octyloxythiophene) film that was deposited on a platinum electrode was found to exhibit electrochromic behaviors, and it switched electrochemically between blue–green oxidized and dark red reduced states. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

双柱塞砂浆泵中工作机构的设计和仿真研究

本文介绍了双柱塞砂浆泵的工作原理，根据机构替代原理建立起双柱塞砂浆泵工作机构的运动分析模型，然后在MatLab环境下，详细介绍了工作凸轮曲线的设计程序，利用计算机设计程序可以方便地分析工作缸活塞以及工作凸轮机构的位移、速度、加速度，利用SIMULINK仿真工具箱进行运动学仿真，为工作机构设计提供相应的理论分析依据。