Green and self-lubricating polyoxymethylene composites filled with low-density polyethylene and rice husk flour

Polyoxymethylene (POM) composites filled with low-density polyethylene (LDPE) and rice husk flour (RHF) were prepared by injection molding. The POM/5 wt % LDPE/7.5 wt % RHF composite exhibited the lowest wear rate, whereas the coefficient of friction remained low, and the POM/5 wt % LDPE/5 wt % RHF composite had the best mechanical properties. X-ray diffraction analysis was carried out, and the worn surfaces were examined with scanning electron microscopy. The results showed that the addition of the filler reduced the crystallinity degree of the POM composites. The main wear mechanism for unfilled POM was adhesion, whereas for the POM composites, wear seemed to occur mainly by fatigue and abrasion. It was experimentally confirmed that the POM composite filled with LDPE and RHF, which is well-performing, low-cost, and environmentally friendly, could be a potential material for tribological applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

A Parallel Deadlock Detection Algorithm with O(1) Overall Run-time Complexity

This article proposes a novel parallel, hardware-oriented deadlock detection algorithm for multiprocessor system-on-chips. The proposed algorithm takes full advantage of hardware parallelism in computation and maintains information needed by deadlock detection through classifying all resource allocation events and performing class specific operations, which together make the overall run-time complexity of the new method O(1). We implement the proposed algorithm in Verilog HDL and demonstrate in the simulation that each algorithm invocation takes at most four clock cycles in hardware.     

The oxidation of two ternary Ni-Cu-10 at.% Al alloys in 1 atm of pure O2 at 800-900 °C

The oxidation of the ternary alloys Ni-45Cu-10Al and Ni-30Cu-10Al has been studied at 800-900 °C under 1 atm O₂. The presence of 10 at.% Al reduces significantly the oxidation rate of the corresponding Cu-Ni alloys during the initial oxidation stages, even before the establishment of a complete Al₂O₃ layer. The weight of individual sample of the two ternary Ni-Cu-10Al alloys at 800 °C increases more rapidly than at 900 °C during the initial oxidation stage. As oxidation proceeds, the weight gain at 800 °C slows down to a degree that the total weight gain after 24 h oxidation at 800 °C is less than that at 900 °C. Due to a faster formation of the Al₂O₃ layer, which suppresses earlier the further oxidation of Cu and Ni, the external region of the scales grown on Ni-45Cu-10Al contain much less Cu and Ni oxides than those grown on Ni-30Cu-10Al. The transition from the internal oxidation to the selective external oxidation of the most reactive component Al in Ni-Cu-Al alloys is favored by higher values of the Al content, of temperature and of the Cu/Ni ratio.     

基于互联网实现多种信息传输技术

随着信息技术的迅速发展,使用互联网实现楼宇内电话、电视、电脑、安防和环境监控、计量数据等信息的合路传输,是实现智能家居和数字楼宇的一种主要发展趋势。最终目的,实现对物和过程的智能化感知。文章首先介绍信息合路编码、中央控管电路,然后介绍网络接口电路原理和系统体系构架。重点介绍多种多样的信息传输技术。它对现代楼宇信息化、智能化建设有很好的参考作用。     

A fonnalism for generating multiparametric encoding gradients in NMR tomography

A general mathematical formalism for generating multiparametric NMR image encoding gradients is introduced. The new schematic approach enables one to construct any desired encoding gradient which may be used in an imaging sequence. Basic gradient waveforms which can be used as building blocks of the desired encoding gradients are presented. A matrix operator for obtaining the encoding gradient for any kind of phase encoding is derived. Specific examples illustrating how to obtain "pure" spatial, velocity, or acceleration encoding gradients for moving spins are presented.     

CHARAC TERIZATION OF TiAl POWDER PRODUCED BY MECHANICAL ALLOYING

The microstructure,alloying reaction and sintering behavior of the powder produced by Mechanical Al-loying(MA)for 8 h from 64 wt.-% Ti powder and 36 wt.-% Al powder were studied by scanning electronmicroscopy,optical microscopy,X-ray diffractometry,differential scanning calorimetry(DSC)and dilatometry.The mechanically alloyed powder partictes are Ti-Al composite particles.Thus,titanium aluminides can formeasily in the powder through diffusion during heat treatment.It is shown that the sintering behavior of this pow-der,different from the behaviors of TiAl alloy powder and mixed powder of 64 wt.-% Ti powder and 36 wt.-%Al powder,changes from expansion at temperatures below 1000℃ to shrinkage at temperatures above 1000℃.Homogeneously alloyed TiAl material with a density over 96% of the theoretical density can be produced fromthe mechanically alloyed powder by compaction-sintering.     

我国化肥催化剂工业现状

全国48家化肥催化剂制造厂总能力为57Kt/a,产量近30kt/a,设备利用率不到50%。平均万吨氨耗催化剂10.36t,高于国外5.60t水平。现生产31个品种203个型号的催化剂中有103种经部级鉴定,但经常使用的约50种。目前化肥催化剂工业水平与国外相比还存在四方面差距。     

Collaborative representation with reduced residual for face recognition

Collaboration representation-based classification (CRC) was proposed as an alternative approach to the sparse representation method with similar efficiency. The CRC is essentially a competition scheme for the training samples to compete with each other in representing the test sample, and the training class with the minimum representation residual from the test sample wins the competition in the classification. However, the representation error is usually calculated based on the Euclidean distance between a test sample and the weighted sum of all the same-class samples. This paper exploits alternative methods of calculating the representation error in the CRC methods to reduce the representation residual in a more optimal way, so that the sample classes compete with each other in a closer range to represent the test sample. A large number of face recognition experiments on three face image databases show that the CRC methods with optimized presentation residual achieve better performance than the original CRC, and the maximum improvement in classification accuracy is up to 12 %.     

直纺长丝工艺中聚酯熔体端羧基值控制的工业研究

本文从工业生产的实践出发对杜邦聚酯技术直接纺工艺中端羧基控制进行了研究。通过对熔体端羧基值对无油长丝端羧基、粘度及纺丝加工影响的分析 ,阐明了聚酯端羧基控制范围 ;通过摸索三个反应釜工艺条件对端羧基值的影响 ,找出了端羧基工业控制的有效途径 ,为同类技术装置生产提供了依据