H型丝光沸石催化剂催化甲苯与叔丁醇的烷基化反应

针对合成对叔丁基甲苯传统工艺中存在的缺点,采用环境友好、可重复利用的H型丝光沸石催化剂(以下简称催化剂)进行了甲苯与叔丁醇的烷基化反应,并用X射线衍射和氨程序升温脱附等方法对不同焙烧温度下得到的催化剂的物相结构和酸性质进行了表征,研究了各种反应条件对催化剂的催化性能的影响。实验结果发现,在适宜的操作条件下,即催化剂的焙烧温度823K、反应温度180℃、反应时间3h、初始压力1.0MPa、原料与催化剂的质量比为8、叔丁醇与甲苯的摩尔比为4、溶剂环己烷与甲苯的摩尔比为5时,甲苯转化率达42.73%,叔丁基甲苯的选择性为96.30%,对叔丁基甲苯的选择性为80.37%。     

3G网络中的IPv6 DNS服务器配置

说明了3G网络中IPv6递归DNS服务器地址配置的三种方法：路由器通告（RA）方案，DHCPv6方案，递归域名系统（DNS）服务器的公认任播地址方案，详细地说明了三种解决方案的操作特点。本文为3G中选择合适的方法进行主机DNS配置提供了指导。     

dU/dt引发的MOSFET误导通分析

分析了MOSFET误导通产生的原因,分别从原理和理论推导两个方面作了分析,主要考虑了开关管中寄生参数对开关特性的影响。通过求解误导通发生的条件,得到哪些参数会导致误触发,最后给出了仿真。文中还提出如何避免MOSFET误导通产生,以及改进方法,对减少实际应用中MOSFET破坏性损坏有一定意义。     

Automatic image hanging protocol for chest radiographs in PACS.

Chest radiography is one of the most widely used techniques in diagnostic imaging. It comprises at least one-third of all diagnostic radiographic procedures in hospitals. However, in the picture archive and communication system, images are often stored with the projection and orientation unknown or mislabeled, which causes inefficiency for radiologists' interpretation. To address this problem, an automatic hanging protocol for chest radiographs is presented. The method targets the most effective region in a chest radiograph, and extracts a set of size-, rotation-, and translation-invariant features from it. Then, a well-trained classifier is used to recognize the projection. The orientation of the radiograph is later identified by locating the neck, heart, and abdomen positions in the radiographs. Initial experiments are performed on the radiographs collected from daily routine chest exams in hospitals and show promising results. Using the presented protocol, 98.2% of all cases could be hung correctly on projection view (without protocol, 62%), and 96.1% had correct orientation (without protocol, 75%). A workflow study on the protocol also demonstrates a significant improvement in efficiency for image display.     

On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

钻井井喷失控井喷流出口速度预测方法研究

失控井喷流出口速度、喷口内压力、喷层产量都是井喷失控处理方案设计、作业施工中重要的基础数据。由于井喷失控井井口环境条件复杂，井喷失控后无法在井口安装测量仪表及在高速喷流中放入参照物，不能直接获取以上数据。文章利用地质、钻井过程获得的地层物性参数和气体动力学方程，探讨井喷失控井天然气喷流在不同井筒流动尺寸及组合的喷流速度预测模型，可应用薄剪切模型或RNG修正的k-ε模型定量描述速度场、温度场、浓度场颁。为井喷失控井处理方案设计、施工作业提供基础数据。     

Routing Correlated Data with Fusion Cost in Wireless Sensor Networks

In this paper, we propose a routing algorithm called minimum fusion Steiner tree (MFST) for energy efficient data gathering with aggregation (fusion) in wireless sensor networks. Different from existing schemes, MFST not only optimizes over the data transmission cost, but also incorporates the cost for data fusion, which can be significant for emerging sensor networks with vectorial data and/or security requirements. By employing a randomized algorithm that allows fusion points to be chosen according to the nodes' data amounts, MFST achieves an approximation ratio of 5/4log(k + 1), where k denotes the number of source nodes, to the optimal solution for extremely general system setups, provided that fusion cost and data aggregation are nondecreasing against the total input data. Consequently, in contrast to algorithms that only excel in full or nonaggregation scenarios without considering fusion cost, MFST can thrive in a wide range of applications     

WC/Cu复合材料制备及其高温性能

用机械合金化法结合冷变形，制备了WC／Cu复合材料，研究了冷变形后复合材料的组织特征和高温退火时韵性能变化。结果表明：烧结后的材料经冷变形，组织呈显著纤维状，WC颗粒弥散分布，密度明显提高，达到理论密度的99．2％；复合材料经600～900℃高温退火，强度和硬度略有下降，塑性则有大幅提高；900℃退火时未发生明显的再结晶，界面结合良好；所制备的WC／Cu复合材料有优良的综合性能。     

复合固体超强酸SO42-/Fe2O3-γ-Al2O3催化合成丁酸丁酯

采用沉淀硫酸化法制备了复合固体超强酸催化剂SO2-4/Fe2O3-γ-Al2O3,确定了其最佳制备工艺条件:硫酸浸渍浓度为0.6 mol/L,浸渍时间4 h;焙烧温度550℃,焙烧时间3 h.并采用该催化剂合成丁酸丁酯,考察了物料配比、催化剂用量和反应时间对酯化反应的影响,确定了丁酸丁酯的最佳合成条件:丁醇与丁酸摩尔比为1.4:1,催化剂用量0.9%(以反应物质量计),回流条件下反应3.0 h,在此最佳合成条件下,酯化率可达95.6%.     

阀控式密封铅酸蓄电池的寿命及失效分析

介绍了各种影响阀控式密封铅酸蓄电池寿命及容量的因素,分析了其失效的原因,并相应的对电池的维护提出了一些建议。